Superb explanation with well built animation. Thanks to you, I'm able to understand this topic really well in a very simple way. Keep up the good work. 👌😊
@FoolishEngineer2 жыл бұрын
Thank you so much for watching!! Please don't forget to subscribe to our channel
@sadunnakipoglu94716 ай бұрын
أشكرك وأقدر مجهودك ، تحياتي لك من تركيا.
@afzaldavoodi73442 жыл бұрын
Thanks, these kind of videos help a lot , before reading equations. :)
@FoolishEngineer2 жыл бұрын
Glad to hear that!
@Timkaasjager2 жыл бұрын
Thanks for the video. My textbook has swapped Q1 and the diode in series with the tertiary coil. That's how I see it in most cases. Which one is correct?
@manu192a6 ай бұрын
What is the best isolated DC-DC converter topology under 500W output power?
@krzsn5382 Жыл бұрын
gracias por excelente explicación, tus videos son lo mejor...
@peterlustig20483 жыл бұрын
Great video, thanks for explaining it so graphicly.
@FoolishEngineer3 жыл бұрын
Glad you enjoyed it!
@sudhakarkulkarni17304 жыл бұрын
Any specific instruction for designing no of turns of reset windings
@FoolishEngineer4 жыл бұрын
Check out this document nptel.ac.in/content/storage2/courses/108105066/PDF/L-23(DP)(PE)%20((EE)NPTEL).pdf
@guybluebag Жыл бұрын
Hi thanks for the detailed explanation, Can you use this to reverse the polarity of the output (i.e +v in, -v out)?
@spmeena21864 жыл бұрын
Thank you sir for right understand
@FoolishEngineer4 жыл бұрын
Keep watching
@exceed59 Жыл бұрын
Hello, can this converter increase voltage or only reduce it?
@FarhanMansuri-i1y9 ай бұрын
How that discharge winding diod becomes forward biased if it is heaving negative at anode from supply and positive at cathode from discharge winding 😅
@funnyreels76616 ай бұрын
It's dot polarity opposite to the main primary winding.
@LEO221162 жыл бұрын
Who the hell is this guy? Thanks for the amazing videos!
@FoolishEngineer2 жыл бұрын
Thank you so much! Please show support to my video with Super thanks and don't forget to subscribe to our channel
@vikasgupta-hl9sq2 жыл бұрын
Supperrrrrrrr. Thanks lots
@FoolishEngineer2 жыл бұрын
Thank you so much! Please show support to my video with Super thanks and don't forget to subscribe to our channel
@Soliha1232 жыл бұрын
I have a doubt if saturation is possible in forward converter then isn't it possible in flyback converter
@FoolishEngineer2 жыл бұрын
because the transformer primary's magnetic energy is being used in the secondary side of the circuit during operation
@mamadyazdi Жыл бұрын
The direction of third winding must wind opposite of primary winding... check forward topology again ....
@BN-hj1wn2 жыл бұрын
Does the Inductance of NT(inductor) must be equal to the primary side of the transformer ? Please reply 🥺🥺🥺
@FoolishEngineer2 жыл бұрын
Not necessary
@김형준-p8x4 жыл бұрын
Hey i am watching here at Korea Thanks for your video, it help well. But i am still feel difficult about forward so do you have any pdf material of forward converter??
@FoolishEngineer4 жыл бұрын
Hi, you can find the link of the document in the description of video
@tanattphokunakorn99122 жыл бұрын
Can it run with only one diode on output side?
@FoolishEngineer2 жыл бұрын
No
@shoumikdebnath91422 жыл бұрын
thank you very much
@FoolishEngineer2 жыл бұрын
Thank you so much for watching!! Please don't forget to subscribe to our channel
@muhamedjakme3648 Жыл бұрын
Thank you But you got the NT and D3 in the wrong configuration They shuld act as power restoration topology once the MOSFET is off and they will be in reverse bias when the MOSFET is on Please check it again
@RAHULKUMAR-vw7nz4 жыл бұрын
When mosfet is turn on then voltage across D3 is zero , how it possible
@FoolishEngineer3 жыл бұрын
Thank you so much for watching!!
@shashwattripathi58722 жыл бұрын
what is significance of D1? Because even if we did not have D1, current during switch on would have been same. Similarly, even when switch is off, then the current due to induced voltage would not reverse biase the D1. You are explaining it wrong. So why D1? I wish you clear my doubt as well as yours of using D1!
@johnjose-gw5qx4 ай бұрын
yeah it is only needed in switch on position, I also didnt get the significance of D1 there
@manuelfilipe72392 жыл бұрын
The Vídeo and explanations are very good. But the subtitles are hiding the circuito.
@FoolishEngineer2 жыл бұрын
You can rearrange subtitles.
@aniketsawant80003 жыл бұрын
I have a question, our source is DC then why transformer is there??
@FoolishEngineer3 жыл бұрын
source is DC but still the input coming to transformer is not pure DC, it is pulsating.
@md.arifurrahman53383 жыл бұрын
Hello sir, Thank you very much for your highly informative video. I have a question about the wire gauges, do we need to select it according to switching frequency or can we use thicker wire. What about the demagnetizing winding and secondary winding gauge?
@FoolishEngineer3 жыл бұрын
Wire gauge depends on the the current flowing through the inductor, but if you increase the wire size, the skin effect increases, so there is a trade of between these quantities
@md.arifurrahman53383 жыл бұрын
Thanks for the quick response, as we know, in single switch forward, when switch turns off, the polarity of primary winding reverses (That's AC effect) and the reset winding does its job. To get the best ampacity we need to choose primary winding gauge according to switching frequency. This part I'm clear now. What about Secondary winding? In secondary winding, the diode only stops conducting when the current becomes zero and works only one way, there is no AC effect thus no Skin effect (if I'm not wrong). Can we use thicker wire in secondary?
@devarajan22914 жыл бұрын
What voltage source u r talking about? Battery? My doubt is when inductor discharges the energy stored in it, will supplies like tdk lambda really take back energy from this inductor?? or its simply dissipated somewhere out of converter??
@FoolishEngineer3 жыл бұрын
Not battery, a constant DC source. Thank you so much for watching!!
@ShaharBenDavid3 жыл бұрын
Small correction.... D equals the ON time divided by the switching frequency cycle time and not by OFF time.
@FoolishEngineer3 жыл бұрын
Please accept my apologies for the mistake!
@abhijeetkunte82213 жыл бұрын
Simplified👍
@FoolishEngineer3 жыл бұрын
Thank you, please subscribe to my channel for more such videos!
@elamparithiparithi33445 ай бұрын
Please avoid background music
@Dailymailnewz3 жыл бұрын
Transformers does not work with DC current it only works with ac.