How efficient are our minisplit heat pumps in the winter

[@TheCrimsonFlash]

We have 7 mini splits with two condensers at our house. Installed them 3 years ago. They work fantastic, even when it gets very cold outside. A lot cheaper than our old baseboard heaters, plus we get air conditioning in the summer.

[@kennixox262]

I guess it depends on where one lives: Here in the very hot desert with relatively mild winters, I have a 6 zone Mitsubishi system but it is ducted with one exception of a ceiling cassette in a utility room/home gym. I could not imagine the ugly boxes on the walls.

[@jimmybrad156]

What's your coldest outside temperature in a typical year?

[@kennixox262]

@@jimmybrad156 Where I live, 30.0 F, is the average winter low.

[@CT-vm4gf]

@@kennixox262That’s why we have choice. What one finds ugly, another might find beautiful.

[@TheCrimsonFlash]

@@jimmybrad156 coldest averages around -20 celsius, but usually it's in the -teens.

[@dirtwhisperer658]

Nice job with the data collection and explanation of findings. I installed 3 mini splits in my house in FL and turned off the old central air. Our electric bill went down from $400 month to $150. To say I am happy would be an understatement. I know a lot of HVAC guys don't like mini splits because they are hard to work on. Right now that is not my problem. If worst came to worst I would just install a new one because the electric is already there and the hole thru the wall.

[@Vigo327]

Impressive data collection. Relating the COP across the temperature range to the frequency of defrost cycles is helpful insight!

[@Thesaltymaker]

Great discussion. We installed a hybrid water heater with similar function to the minisplit from a gas water heater. You’ve inspired me to start collecting a bit more data with external sensors. Of course, to proof is usually in the utility bill.

[@crfuzz1144]

I installed a DIY 18K unit over the summer (primarily for AC). I've been quite impressed at the offset it's produced to the oil boiler, especially in the shoulder season. Rough math so far has me saving half my annual fuel oil usage, with a modest increase in electrical usage. Fuel oil is around 5$/gal, and I usually use 6-700gal/winter. It's paying for itself quickly at this rate. Would love to have the granularity of the data you collected though!

[@rockymountainman7]

I would look at insulation first

[@chrisE815]

​@@rockymountainman7 they already installed the unit?

[@chrisE815]

Yeah, your numbers are spot on. In my case, heating cost is about a 1/3rd compared to using my oil fired boiler but that's because my boiler setup is super inefficient. Just going to a cold fired boiler would be a huge cost savings in my case.

[@rockymountainman7]

@@chrisE815 A lot of people who read this have not yet installed anything. My advice to people who think of making a move is to look at the insulation of their building first. Insulation you buy once and you benefit for every year after that. Insulating can cut down your energy use so much that it doesn't make sense anymore to make an expensive switch to something else.

[@vaskoa]

Interesting. I've always wondered what is the efficiency of those things,... I've seen overall numbers anywhere from 2 to 5 times more efficient. Thanks for all you testing Matthias, this is very informative.

[@sashqa0]

Finally got it up and running. The only delays we had was because we realized we needed some extra parts (I’ll list that below) kzbin.infoUgkxihMYiJNXcHdbH-7ihymsLz61l7jVyb5O . So we have a loft where our current hvac just couldn’t seem to keep cool during the summer. We have been using a window unit since we bought this house over 6 years ago (all the houses in this neighborhood were built in the 80’s and majority of the houses built like ours use a window unit). I hate window units because they are just so noisy and the one we had really only cools one side of the loft. I had contemplated upgrading our current HVAC, but with all the rising prices these days, it would take years before saving up enough to do that. With the advice of my father-in-law (used to run an HVAC business), he recommended we get an inverter instead. We thought we bought everything we needed, but there were just a few other parts we didn’t anticipate needing (which is what caused most of our delay). My friend and father-in-law did all the work to get it installed and running and now we have nice cool air circulating nicely throughout the entire loft. It is very quiet and even the outside unit is much quieter than our main HVAC unit. Saved ourselves thousands getting this.

[@nunyabusiness5075]

Thank you and good job on including the defrost cycles into your COP. Plenty of people wouldn't include the "bad" parts and instead would just tell themselves how smart they are using a mini split. COP tends to dive below 2 when it gets cold, and between that and the high cost of electricity here ($0.34 per kWh) a mini split is no better than the cost of heating oil.

[@geraldhenrickson7472]

My 8,000 / BTU seer 21 Pioneer split heats my 23 foot travel trailer at 8 degrees no problem. It draws a constant 400 watts to do so. Above freezing, in the 30’s it draws around 240 watts and cycles on and off. My trailer is super insulated with R15 in the walls, R23 in the ceiling. There is nothing like the luxury of good insulation and one of the more efficient mini-splits. Of course a high Seer rating and the time of purchase it a bit difficult due to the initial cost being nearly twice as much. Because my power requirements are so low in both Summer and Winter, I can run all this with solar. Note that when initially started and the Pioneer is running at maximum effort, it can draw as much as 980 watts for a short time. Thanks for the video.

[@anttitiilikainen8543]

In Finland covers or canopys for air pumps outside units are rather typical, those would prevent snow issues. Would assume that depending on model they would somehow impact to air flow also, but guessing they would have minor impact. They also hide the ugly white plastic, which seems to be only option by many producers. Considering to make one with homemade bandsaw?

[@jothain]

All AC guys I've talked have said to never use those covers as if they hinder even bit the airflow, efficiency apparently drops quite much. Don't know if that's true, but guy who installed mine was at school same time and I believe him. Outdoor units are indeed though quite ugly. Outoa kun meinaa, että imee lunta kitusiin. Ei itsellä ainakaan ole moista ongelmaa ollut koskaan.

[@Realism91]

I was thinking you could build one like a custom range hood with a style like shaker or tudor or something, even copper or steel if it looks good with everything else. If it's big enough it shouldn't affect the fan much I would assume, but how big before it looks ugly.

[@everythingexplained]

​@@jothain That is not true that you should avoid using covers! But what one should consider is the area of the intake fins, and that the available area around the unit should be greater than that. The instructions recommends a minimum distance from wall and surrounding obstructions, so your AC guys should pay attention to those instruction. Almost all outdoor units suck air from behind and blows out the front, if you block the top and one side of the unit, the remaining area on the bottom and the other side should be as large as the whole fin section.

[@jothain]

@@everythingexplained that's not true either. Check out Mythbusters. I think it was there proven that those areas are actually really small that need to be in use. Reasoning on ac guys seem to be that airflow needs to be very laminar and even small obstruction would break that.

[@nathanbrown5099]

@@jothain As an HVAC guy myself I agree generally any type of cover will hinder airflow decreasing efficiency way more than it will help with defrosts. If you are going to do something of the sort you never want to cover the sides and you want to leave ample room above the unit for air flow. I believe minimum distance above for a awning type cover is somewhere in the 2-3 feet range.

[@ZrubekFamily]

Build a cover for those outside units to keep the snow away, should help a lot.

[@sfan2767]

Yup, even just covering the top of the intake side would probably do a ton without hurting the airflow enough to matter.

[@dannyjepp985]

I think this would be an interesting experiment. If the fan is moving a lot of volume, a smaller cover wouldn't prevent enough snow from getting pulled through the unit. A larger cover would limit the amount of snow, but could limit air flow and not distribute temperature as quickly, making the unit less energy efficient overall.

[@JeffDM]

I want to build a large "winter" housing with screen mesh intakes to see if I can keep the fins clear of snow.

[@barthanes1]

I don't think you would need any kind of screening. Just a large enough roof over the unit and maybe some slat walls. I think screen might get packed full.

[@matthewcantrell5289]

@@barthanes1 exactly. It’s a lot easier to shovel around a large cover than trying to clean and de-ice a screen

[@tau9632]

Man you are amazing. I'm off the grid in a tinyhouse, so every Wh counts and I've been dying to know about all these things! Thanks for all the work! On a fun note: it's crazy seeing your numbers of 80-100kWh per day, compared to my 5kWh per day D: :D

[@jarigranroth6873]

Leave enough space around the outside unit when making the shield. If the air flow is bad the efficiency drops

[@VarionJimmy]

Or hear about “cheap electricity” when we in Sweden had around 3 - 6 SEK (0.3 - 0.6 USD) per kWh in December. Contrasts.. 😁

[@BoBandits]

@@VarionJimmy wow. Here in Toronto I pay $0.10-0.14… 7k is like $1

[@cooperised]

100kWh here in the UK right now would be around £34 at the domestic rate. That's probably $40 or so US. 😱

[@aleksanderkac7530]

What do you do to consume 5 kWh per day in a tiny house? You need some more efficient appliances man. I run a regular house with 2 freezers, 1 fridge, washer (no dryer), stove, water pump, water heater, computers, lights, 60 inch tv, ... on not much more, about 6,5 kWh per day. All A class european efficiency score appliances. Freezers consume 90 kWh per year.

[@TOMA21207]

Yeah they are great, I have mini split of that particular manufacturer Midea, I think they are more efficient because they are using inverter motors for the compressor. I'm very pleased with the mini split unit so far, they are up to the job.

[@Hunter271828]

I love this video, I just put a minisplit in my workshop and have been thinking about doing similar tests, but it seemed like too much work. Thanks for doing the work for me :) !

[@JonnyDIY]

And here I just complain when my utilies go up 🤣 I love it, nice job Matthias. Looks like it was a great investment 💕👍

[@Little_B]

I installed a mini spit in our house in December of 2021, I've not seen mine ice up,even after our paltry midwest snow yesterday. I really appreciate seeing the visual evidence that I suspected about its energy efficiency, I feel like between the air conditioning and heating,I've saved a ton over my natural gas,and old air conditioner.

[@TimTurner115]

Thank you sir. That's why we went with mini split throughout the whole house and electric tankless water. But I live in Texas.

[@yossarianmnichols9641]

Very interesting effort on your part to measure the COP. You showed just how difficult it is.

[@daniellemos5364]

If you have extra temperature sensors I’d recommend adding one each to a liquid and vapor tube on the coil. It should help you monitor how efficient the OD coil is performing. As long as that temperature is close to outdoor ambient then your od coil is performing well.

[@nobody8717]

Yeah i'd second that suggestion. plotting the actual inlet/outlet temp of the exchanger would give you direct info on it's efficiency.

[@everythingexplained]

Since this is an inverter unit, measuring the temps on the refrigerant is not that informative. The unit will have pressure and temp sensors giving feedback to the inverter that control the compressor and changes the flow in the system. The one thing I could think of is for detecting unneccesary icing of the evaporator, ie. liquid temp and gas temp are close and way below outdoor temp, but that should the unit detect. To see if the unit is performing well you should measure the power that the unit consume compared to outdoor temp and indoor temp.

[@doozer2726]

Thanks for the thorough and detailed research. I was considering a similar split unit here in the UK - more for the air con. But the real world data about the heating aspect of it is appreciated. I was skeptical they could perform as good as they state.

[@davidwx9285]

These things are super common in Sweden and has been for 20+ years. I use one to keep +8C in my workshop. Works great! Also common is geothermal. My borehole for the house is 250m deep.

[@Manofcube]

What goes in the hole?

[@kenk8215]

@@Manofcube I believe it's usually antifreeze.

[@mrjozza5924]

@@Manofcube U shaped pipes with ethanol. It pumps cold liquid, and brings back heated liquid, so it takes temp from the ground below the house.

[@dimmacommunication]

@@mrjozza5924 Unfortunately we don't have those wells here in lower europe

[@TornadoTromboss]

@@dimmacommunication It's a borehole, we have those (it costs money to bore ofc). Now here on private Land we are only allowed 100m i think. But we do have warmer temperatures overall, so it's fine.

[@forerunnert]

Mini splits are amazing, we're using one since this winter. Some are better at heating than others though, COP 4 or 5 is doable for really optimized ones. Around zero C we're using the same amount of electricity of 3 dishwasher cycles per 24 hours.

[@markae0]

Great video! Yes, I also would add a roof to the outside unit. Join the house wall to the top of the unit to stop the snow from being sucked in. Maybe a few inches on the side. The remaining 75% air flow on each side should be enough.

[@wholeNwon]

Very informative. As you alluded to, in pursuit of efficiency and economic pay-back, one must always consider the complexity of the systems and therefore their reliability. One significant repair could consume all of the fuel savings and more.

[@burns375]

I have a Mr Cool which i believe is a similar unit and another cree. They both do a great job. Your observations match mine exactly. Doesn't do the best in cool humid air, builds up with ice. Once the air drys it does alot better. I keep a wifi temp sensor near the output and have been monitoring as well. Outside humidity can make a huge difference in how quickly the coil reaches max temperature.

[@infiniteinfinity9802]

My MrCool was not heating and I read the manual only to find that the indoor unit thought it was 79F inside. So was able to set it to Follow Me and that makes the remote the thermostat. I put the remote 20’ away and the unit started heating again. Wondering how it will do in cold winters where we can easily have some -10F days.

[@vennic]

Just the fact that this is on your channel I know that this will not be just another "well, it feels more efficient" video

[@andredsouza2320]

I've been watching all of your videos for a while now and only today found out that you are in NB. Hello from Fredericton. Moved here a few months ago and absolutely love it so far!

[@yingchen6236]

Very scientific, very impressive. Thanks for the great video!

[@tomschmidt381]

We installed a minisplit heatpump last year and used it that winter. This year in New Hampshire electricity is extremely expensive so we are only using our cordwood stove. We have an LG red system with two compressors and six indoor units. I didn't notice much in the way of defrost cycles last winter but I was not monitoring it as closely as you are.

[@caseytrudeau]

some great information here thank you for putting this video together! I did want to give you a heads-up that when the units go into defrost, they aren't heated up with an electric element, it's the refrigerant inside the coils that are pumped in reverse. that is why you felt cold air when you turned it to air conditioning mode to dethaw it.

[@6Ginge]

And in defrost, the indoor unit fan is off to stop a cold draught in the room.

[@MCsCreations]

Pretty interesting stuff, Matthias! Great testing! 😊 Stay safe there with your family! 🖖😊

[@elixier33]

I've used air conditioning all my life for both heating and cooling. I'm from the UK Daikin 1800 BTU split x2 stick it on brackets put it on the wall outside works a lot better. A decent AC will run the inside fan very slowly in defrost. I'm happy with both my units even at - 10 Degrees C.

[@stamfordmeetup]

Nice video and a nice brick house too. Better than the wooden shacks south of the border.

[@jasonallen7091]

Fantastic video! Thanks for sharing your data

[@IceDragonUser]

If you want to prevent frost on the back of your unit, try putting some propylene glycol into a spray bottle and spraying a thin layer onto the freezing surface.

[@1987FX16]

Build a little lean to coming off the house to cover the outside unit. It'll help with snow ingest in winter and with direct sunlight in summer. Increased efficiency year-round.

[@RadioHist]

+1 on some sort of cover over the outside unit. My unit is not up against a plain wall... My workshop is on piers with air flow under it (floor joists have insulation between them) So air into the unit is coming from a sheltered area. The little corrugated plastic roof extending out over the unit from the shop wall therefore does not restrict air flow. That roof helps also to keep debris from being sucked into the coils.

[@Lizlodude]

It's so satisfying to go "Hmm I wonder how this thing perfor- Ah neat Matthias (or Project Farm) tested it!"

[@johnnygarcia7386]

Great work. Thanks for sharing.

[@nelsondog100]

Very informative, thanks It would be interesting to see some data from a tankless water heater in comparison with the storage tank variety. Food for thought sir 🤔

[@spookje111]

Thanks for the insight Matthias.

[@Soothsayer210]

Nice video. Someone told me if you keep your mini splits outside in an enclosed environment like a box, it saves a lot of energy since it will not be exposed to elements. This could make the number of times it needs to defrost less saving energy. I don't have one myself so it is just something that i heard and thought i will let you know.

[@h82fail]

Cover from elements and shade from sun is good, but restricting the airflow is bad. Roof with no walls would be ideal but most people want to hide them vs draw more attention to them.

[@orangetruckman]

Your channel is super underrated!

[@robertomartin8731]

One of our unit have an auto de icing so it stops heating for a couple of minutes when it detects icing. It is computer controlled and even have prepare mode before heating in the morning. Our other unit is just cheaper one and heats non stop until it ice up. We don't usually use the dumb one because it is the bedroom. The smart one is in the living room even have an app so you can track your 2 years of power usage. Current year is overlaid over last year.

[@SKEPT_OMBAR]

After 7.42 I realised you have reached level 100 Electrical Engineer. I was trying to guess if you were mech or elec, but the instrument comment is 100% elec haha! im mechanical, and loved the content. PS most elec's always take it to the next nerd level and that brings me great joy! I found this video by looking into misting the condenser (in cooling mode obviously) to increase the efficiency, my search is inconclusive and you have all the gadgets to run a test in summer.

[@matthiasrandomstuff2221]

it will help, but I don't think its worthwhile. Increased complexity, increased corrosion, reduced lifetime.

[@SKEPT_OMBAR]

@@matthiasrandomstuff2221 After everything I've looked into, I agree. My water is quite hard and the calcium build up will just kill the efficiency long before corrosion kicks in. However, I ended up setting up a manual misting system to assist on hot days >40 deg C and it made a noticeable difference. I would be super interested to see what results you could get even if you just mist with a garden hose for 30 minutes.

[@nkuete]

I think my minisplit system has resistance coils in the outdoor unit to defrost itself. I didn't realize that some units didn't have this. Love your data gathering and analysis!

[@wobblysauce]

This is the key with reverse cycle systems, it is one valve and little electrical change between heating and cooling but does it in one vs independent units.

[@ssaasszza]

Very good informative video. Recently I switch from excel to python+seaborn+jupyter, and drawing nice chart from data you have is much much better :)

[@glenschumannGlensWorkshop]

Your attention to detail and knowing how to measure are impressive. Have you considered placing a roof over the mini split outside unit to keep the snow off?

[@paulettelambert7965]

They’re made for outside. No need to cover…

[@rtyrtyrtyus]

@@paulettelambert7965 But it would mean less defrosting cycles. That was the whole point in recommending a shelter for it. Plus it would be less likely to rust so soon. Have you seen how those things have rusted before? You see them frequently all rusted up. Hopefully newer models have learned.

[@birdyflying4240]

When you live in a coastal climate it is very important to cover the AC unit, otherwise the casing will be damaged in a few years. Covering it will save you many years of use and money! I live in a coastal region and had a AC go bad in 5 years.

[@johnhammond6248]

ayyy i see that surge protector on your disconnect, my man. Good on you protecting your investment

[@jestempies]

Very useful view, thank you.

[@jspinosa50]

Excellent review thanks

[@bigturk83]

We have had a mild winter this year (im in Freddy too). Im down 800kwh from same time 2022 and 1200kwh from 2021. This week will be a good test of the minisplit! Brr.

[@pgerry9400]

If snow ingestion is an issue , I would build a small shelter over the outside unit that still allowed sufficent air flow.

[@thomask4836]

Matt, This was very interesting. I understand they are more efficient than resistive heating but its hard wrapping my mind around it when they are driving a compressor. Just a suggestion for the summer months eh! I've seen the evaporator units make a mess of the walls when the condensation drain clogs up. Be sure to keep the drains clear! Best Wishes, Tom K.

[@Bbonno]

When trying to understand how these work it helps to think of them as oversize, reversible fridges with fans.

[@-TTimo-]

Explains a lot of things about my own mini-split in winter. I'll have to check if it ices up when we get snow ..

[@eh42]

Your experiements/work with cyclone seperators should come in handy for building a duct for the outside units that settles any snow out before feeding dryer air to the unit.

[@SuburbanDon]

I really dig these videos man. Thanks.

[@mikedennington8856]

Build a cover around it and you will find a huge difference. I did it and noticed right away.

[@jsjs6751]

A roof over the unit usually doesn't hurt the efficiency that much, but building a cover around it probably will.

[@Alexander84129]

This channel should be called “How much you can accomplish when you don’t watch TV”

[@pete3897]

Here some of our outdoor units actually have a resistive heater coil around the outside refrigeration coils to periodically defrost ice blocks without having to reverse the system :) They call sell those models here in the more southern areas (they cost more and the feature isn't needed in more northern areas).

[@wesleyhughes3946]

I have no idea what you're talking about. Post a picture?

[@infiniteinfinity9802]

Please include Fahrenheit in future videos if you can👍 Watching you from US. Just had to check all the numbers while you were speaking. Sounded very cold in Celsius but not as cold in Fahrenheit. Very informative video. Thank you!

[@djrenault]

i received a presentation on samsung VRF systems at work recently, where they showed that they have air pressure differential sensing to determine if the unit is iced up, so that they can potentially run the defrost cycle less frequently. not sure if others do this too, but thought that was cool

[@krenwregget7667]

very interesting as always.

[@RDhali]

I love that you're still rocking the classic Rim fleece, probably some of the best company swag we were given lol

[@matthiasrandomstuff2221]

that was the best of all the swag. Super warm.

[@gordon6029]

Thanks for this video.

[@thewitherslayer9669]

This is great info, thank you! Also, I loved you in Season 3 of Stranger Things.

[@Don-sx5xv]

Great presentation brother, I live here in New Brunswick also, just installed 4 , seeing how I can get the best efficiency, you were very thorough, going to check out more of your vids TY

[@wookievr641]

Im running mini split in the garage/workshop. Runs year round to keep temp up and reduce moisture in the space. Prior install ran dehumidifier that was a power hog in comparison.

[@laynelommen9460]

Great video.

[@nobody8717]

my apartment has a similar unit, we don't use it in the winter due to the building's baseboard radiative boiler heaters, and the lack of consistent airflow. But dang is it efficient.

[@twx8626]

Hahahahaha you are a real electrical technician bare board wires everywhere.)) Thanks for sharing

[@Lagittaja]

Build some form of an enclosure/roof for the outside unit. That's a fairly common thing here in Finland.

[@fergusontea]

We've had warm winters since you moved down here. Thanks! LOL

[@matthiasrandomstuff2221]

2018-2019 was not warm!

[@biggig06]

You're amazing!

[@markb3146]

Here in Australia, we pretty much use them for cooling. trying to sleep at night when it is 26 degreesC and 80% humidity is impossible. Can't live without them in Summer in my part of the world

[@fredwinter2978]

poofter

[@davewilson6859]

I install these for a living .I would recommend putting a little roof over the unit keep snow and ice off.

[@PabloEdvardo]

i like to imagine your wife nodding like she's acknowledging an excited child as you tell her about your graphs

[@jangoofy]

10:48 - would absolute humidity (g/m3 H2O) be more relevant ? It is after all the amount of water that freezes to the coils. +5 C / 80 %RH = 5.5 g/m3 H2O vs. -5 C / 80 %RH = 2.7 g/m3 H2O.

[@NageebTheAverage]

We installed one of these as part of an IT server room hvac and the contractor specifically mentioned us requiring a sub-zero add-on to prevent the unit icing up (winter operation in southern Ontario). Perhaps you might want to speak to your hvac person to get information on that.

[@rkan2]

That is called a resistive heater :D Just makes the COP even worse.

[@NageebTheAverage]

@@rkan2 I never realized that’s all that it was. Yeah I guess that would definitely skew the numbers in the wrong direction. Lol

[@TFlorian]

Very interesting !

[@jean-christophenicaise1614]

I Mathias, thanks for your video ! interesting to know others "country" electric consumption :) here in Belgium at a price a 0.5€ by KWh, it would cost sooooo many ... actually impossible for common peoples to pay there bills ... Some math : 0.5 x 60 X 30 : 900€ by month !

[@rud]

I am experiencing the exact same thing with my 10 year old mitsubishi. Around 0 it needs to defrost much more often, every 1-2 hours. Also it has a heating element in the bottom of the outside unit to prevent water to freeze in the bottom of the unit when defrosting.

[@thethingsbypete7195]

Which sensors do you use for inside temperatures (the graphs @10:22)? They seem to have a very good resolution ...

[@wildwoodtop]

This Dude is a Graft Warrior! 🤟

[@johnhubert339]

If you could build a small roofed area over your outside unit, it would not only keep the snow off, but the cooling effect from the shade might help during the summer, albeit, marginally.

[@hali_moto]

If you get enough ice build up that you need to assist the unit in defrosting, you should ensure all ice is gone otherwise it will start building again in the same areas. In a worst case scenario the ice can shift the coil and damage it. Warm water can be used to melt the last bits of ice.

[@Forbes123]

Great content

[@NZherewecome]

Your unit will have a thermistor on that outdoor coil. The board will look for a reading for defrost to activate. It’s normally a temperature after a time period.

[@douglasthompson2740]

It is always worrisome when the coils freeze because the expansion of ice as it builds up could easily fracture some of the thin coolant lines. I also have reservations about keeping circuit boards in a very wet environment.

[@matthiasrandomstuff2221]

coils ice build up is typically thru sublimination. As such, there is no liquid to solid transition happening on the coils, so I don't think the water expanding when freezing is an issue. Except for perhaps the remaining drops of water after a defrost cycle.

[@KasperPilsted]

Now come summer, see if you can increase the efficiency of the AC by running a misting nozzle over the outdoor unit while it is running :)

[@helmet098]

I got a Mr Kool DIY mini split ad before this video lol

[@stevenspmd]

I got 3 daikin aurora units installed under the federal/provincial program; with the rebates the 3rd one was almost free.

[@Neeboopsh]

your videos are awesome. ultra nerd stuff.

[@menchelke]

If you turn on the Turbo mode, that will force the basepan heater on and warm up the house more quickly or hold a higher temp over night, of course at the cost of more power usage. Mine never ices in AZ.

[@Alwayzsmilin]

If you could tie into the control board, ie. like BACnet integration, you'd be able to get inlet/outlet temps, coil temps, etc.

[@dah1777]

Here in the north of Scotland we find that there ios more variation due to the high relative humidity and the significant number if days that are cold, around freezing but wet. As such the defrost cycle has to run far more often.

[@millsbrian55]

Nice work! Could you place a roof above the outdoor unit to prevent snow being sucked in?

[@matthiasrandomstuff2221]

That would help during snowfall, but not condensation when its just generally humid (which is more often the case than snow falling)

[@bigpicturethinking5620]

I love my mini split.

[@robertbolen4151]

Super helpful

[@rivergate950]

11:00 the 33 seer units have a COP of about 4 when the outside temperatures are around 45F. I'm sure it is less when it's freezing outside,