How I built my HOMEMADE Lathe!

[@stanfischer6175]

I have a whole garage full of real machines that I've acquired over 30 years. I admire what your doing greatly! A little suggestion, if you were to make a lathe all over again design the fabricated bed in such a way you could fill it with concrete! This would greatly add to its rigidity and dampening ability. During WW1 Lathes were needed so quickly there was no time for foundry work so beds were tubular/bushing slides and concrete.

[@stringlarson1247]

That's a great idea. Stealing it.

[@1972andrewf]

It would be awesome if you could .make a list of part and sizes that you use.just incase someoneelse would like to build one similar to it

[@SimEon-jt3sr]

Hell yeah. Thanks for the info I thought about making a concrete table thing with plate steel on top, could be a really good work table, maybe some type of plastic or composite between the two so it lasts longer. Also concrete base for a vise stand, or other surface/holding.

[@2500brandon]

Great job looks awesome. If you were blackening those gears u r good but if you were hardening them then need to be red hot before you put in oil

[@Neally]

Thanks! And yeah, it was just to blacken them for rust prevention

[@2500brandon]

Lol I totally realized that your too smart to not know that after watching ur other videos. I jumped the gun. Great content keep it up thanks

[@Neally]

@@2500brandon Thank you, friend, I appreciate it!!

[@dustinweatherby5518]

I think the hand made gears were the most impressive for me, i had no idea gears could be handmade with enough precision to be worth a darn. Awsome job on the entire project, i feel alot more confident in trying to build my own now

[@Neally]

Thank you, I appreciate it! I'll be honest, I as surprised by them too😂

[@stringlarson1247]

A friend sent me a vid. of a guy making gears for a wrist watch on a tiny lathe. Chronova Engineering is the channel.

[@jaisonmahadev1599]

Great build,actually magnificent ,perfectly suited for a tight budget.Hell man it does the job,You got my subscription.

[@Neally]

Wow thank you! I appreciate it!

[@markhedquist9597]

Welp, you got a sub outa me! That's the jankiest lathe I've seen yet, and I love it! I read your response to another comment about "dipping your toes..." and, I totally get it. I have gobs of machines I want to build. Some half started and set aside to start another. Lots of respect from me for bringing this one the distance of actually making chips! Gonna check out the rest of your videos, and hope for more! Keep on chuckin!

[@Neally]

Thank you! Much love

[@thechronicgeneralist]

That works way better than I expected when I saw you welding the heck out of parts that are expected to drive tight tolerances. Shows the value of not overthinking things I guess ;-)

[@Neally]

Thanks!

[@stringlarson1247]

I'll second that.

[@jbaker8871]

Really great work brother. Many ppl don’t want to put 400 hrs and thousands of dollars when it’s used for hobby or small jobs for convenience. Well done!!

[@Neally]

Thanks friend, I appreciate it!

[@ARMYStrongHOOAH17]

Your video editing skills are remarkable

[@Neally]

Thanks! :)

[@backyardmachinist]

After I was first introduced to machining I wanted to build something like this. I eventually got a mini lathe, but it's interesting to image what can be achieved with such humble material. Well done

[@Neally]

Thank you!

[@mrschnider6521]

How come you guys are not building guns? your going to make engines? what a waste of talent.

[@mrschnider6521]

anyways, that was a very impressive build. Somethings you just cant teach, those are the gifts god gives us, why one person can just sit down and build a lathe out of scrap materials and another person wouldn't be able to do it with a gun to their head is beyond my understanding. The point is these people come from all walks of life, when looking for talent disqualifing people based on where they went to school, what city they came from, or what company they worked at doesnt make much sense. Some of your best men will have not even gone to school, others may have a phd, some are from poor families, some from rich, but in the end all brilliant people seem to find their way to the same place. And that is what makes the USA the best country on earth.

[@beautykhusiyadiary5949]

​@@mrschnider6521 ws

[@beautykhusiyadiary5949]

​@@mrschnider6521 ws ws

[@mishman]

Simple and creative plus you welded it with stick. Very inspiring!

[@Neally]

Thank you very much!

[@MrPlumber27]

What do you mean it’s not as good as a store bought lathe ?!! Yours is better than my vevor 8x14” lathe !! Suggestion, if you want smooth finishes and no bumpy bumps it’s incredibly important that you get your x and y axis as rigid as possible with absolutely no movement. That way when you go to turn your part the tool post doesn’t move and your chuck needs to be extremely rigid with zero give. Also bolt your lathe to the table or tack it in place if you have a steel table . If you do this you will be able to make incredibly accurate parts down to the thousandth and below.

[@chrisfreeman5975]

I think you got the right idea. if anything the best way to learn to use a lathe is probably to build one so I think you've got the right plan. I find you to be quite inspiring thank you. Keep up the good work.

[@Neally]

Thanks!

[@DobleWhiteAndStabley]

Dude. Add some caste parts in there. Add a bit of finesse and refinement to your build. Make it look PURDY. Like, I'm pretty sure a caste tailstock would be badass.

[@botak333]

It posible for steel or alumunium?

[@dillonhayes3402]

Here I am trying to turn one of my 5 angle grinders into a small wood lathe and stumble upon this bullshit... I'm more than impressed how bloody well that worked 😂 makes me want to be a bit more ambitious than making a simple wood lathe hahaha but I haven't welded in years so mine would never slide and would probably be banana shaped from too much heat

[@Neally]

I was thinking the same thing, but then I figured a banana shaped lathe is better that no lathe at all😂

[@hareget4541]

A piece of tight budget artwork. I really liked the idea although I am want even on tighest budget. I would like to request you if you could send the drawing for making one.

[@Neally]

Thanks, I appreciate it! Unfortunately I don't have the drawings for it anymore

[@ebrahiemmurphy6506]

Thanks for sharing , you impressed me with your lathe, believe you will make it better. I didn't think it was gonna work all that well , but pleasantly surprised keep up the good work ,new sub as well. I've bought a lathe chuck 2 years ago, with seeing your results , looks promising and will try it too. Try turning with some cheap Chinese lathe tools . Loved how nice the cross slide worked.

[@Neally]

Thank you! I appreciate it :)

[@carolineswelt]

Funny and entertaining! You're so talented, hope to see you once on tv with your own show! Go for it....you're getting better and better! ( don't forget the german # for more fans! 🤭😏Your Aunt from Germany.

[@hhkk6155]

With that kind of craftsmanship - everything is possible 💪

[@Neally]

Cheers! Thank you

[@NicoyHarrison]

Would really love to do this hopefully u see my msg

[@beastman.330]

I was going to make one by using a front wheel drive car hub bearing and a drive shaft which will be connected to a zxr400 engine and gearbox.

[@Neally]

Link me a video of that because that sounds gnarly😂

[@bikerrealengo]

Verry funy when change the chuck for a stone 😅

[@stringlarson1247]

This is f'n great. Please use cutting oil/fluid do I don't cry. :) Re. milling with drill press: I just picked up a '40s era Craftsman benchtop press to make a mill for 'light' work. The thing weighs ~280 lb. The head is a big honking' (tech. term) chunk of cast iron. I love the irony (pun) of needing a lathe to re-size the rod to make the lathe. Nice work using a grinder on that and everything else. +10 for the use of layout fluid!

[@Neally]

Thanks! Greatly appreciated ✌️

[@Mircone1996]

AWESOME man, awesome. i will try myself to replicate your work. Just a tip: the eccentricity of the shaft is due to the grinding @3:44

[@Neally]

Thank you!

[@yeldarb141983]

not gonna lie, I was expecting something man-powered (been looking at treadle mechanisms, hoping to find a useful diy build my complete lack of skills or geometry knowledge could work from for my own project), but this is pretty awesome all the same.

[@Neally]

Thanks!

[@yeldarb141983]

@@Neally Not a problem, just gimme a small credit when you make it man-powered, lmao

[@Neally]

@@yeldarb141983 you got it bro😂

[@fouadmeddah3174]

Ayo this rocks for real , Would you mind if I asked for your blueprints or weather I can like use your ? Thanks for the response , hope it'll be alright with you .

[@Neally]

I don't think I have those files anymore, but they wouldn't help much anyways because the majority of the build was improvised along the way. Thanks! 🤘

[@sj1122334455]

Lap your surfaces together to try and get a little slop out

[@DanSpartanu]

Of all that was seen, the only good things were the drawing and the humor

[@Neally]

I'll take that as a win, I guess lol

[@loicverniers4429]

you lit yourself on fire and your reaction was just omg im on fire haah

[@Neally]

Of course! lol

[@ashpelser3950]

People forget the lessons learned during a project like this. Keep it up. You got my sub.

[@Neally]

Definitely! Thank you!

[@xylemmelyx]

Extra points for setting yourself on fire, but not making a big deal out of it. I have a pile of shirts with smallish crusty holes in the lower right side.

[@Neally]

It's sad because I really liked that hoodie😂

[@jpharmon7343]

throw an ac capacitor on it that will kick the engine into running. when your ac kicks on outside that initial jolt of sound and hum is the capacitor jumping the motor... definitely just subscribed though!

[@Neally]

Thanks for the tip!

[@ianrs4685]

washing machine rear bearing mount solid as

[@raa6504]

I'm impressed with your skills and I'm in the same position, I wanna get into this but no way i'm going to spend 2k on a lathe. You inspired me to look into building it. The quality of your video is also very good.

[@Neally]

It's an awesome project to get into! Thank you🤘

[@raa6504]

@@Neally please don't give up and keep posting. Your editing, charisma and talent are awesome. This channel will blow up.

[@amusaelalmajad3592]

What pice crap !!! But considering 🤔 than is made from thrash ...I will said is a big step for human kind !!

[@Neally]

Thanks!

[@alphaindustries5775]

Amazing video! I thought you'd need something more precise then a length of stud for moving the carriage but I guess I was wrong! Making a carriage that could be swapped out and put on a drill press to make it into a mill sound like a pretty neat idea, I might have to try it out!

[@Neally]

Thank you! This thing was mostly just a proof of concept, so it's nothing too crazy, but I wanna give it another shot soon and make it better. I'll see if I can incorporate that idea!

[@Γιαννης2]

Ok, i have passion with lathes, but reason for subscribing is the AWESOME SONGS !! that covers your video. I loved that. So, no mute for your channel..

[@Neally]

Sweet! Thanks!

[@Skepsis1358]

This is my kinda youtube

[@Neally]

thanks haha

[@CECS1]

Hey. Fabulous job man. I'm wondering if you are willing to share your design drawing?

[@Neally]

Hey thanks! Sorry but I don't have the files anymore

[@Biokemist-o3k]

A video so awesome I had to subscribe!!

[@Neally]

Thank you, my friend!

[@Biokemist-o3k]

@@Neally Hey brother Are you out here on the East coast like me in Pa maybe???? Oh yea by the way your welds are getting very good. Especially for a stick welder.

[@ProdigiaGames]

Wishy washy bullshit engineering? That's my favorite kind of engineering! 🤣

[@Neally]

It definitely keeps things interesting!😂

[@marvlb]

A lathe is a machine that can turn square metal round and round metal square!

[@Neally]

Would it be fair to say that lathes make the world go round?? Cheers!

[@JamieSpencer-q9n]

I would like to see you make a working/running car crankshaft after you get it built. I would subscribe to you if you could.

[@baddonkey6876]

Alright dude, ya got my attention, im subbed

[@Neally]

Thank you, my friend!🤘

[@jekekefe5923]

I'm subbed too just keep the good jokes up

[@witchyphil]

Ace job man. I'm going to build one but with a solid shaft and pillow block bearings, but with ideas stolen from your build. Thanks in advance for the ideas, but if you've already patented it disregard all I have just written. Well done.

[@Neally]

Go for it! The block bearings are definitely a good idea, but I would keep the hollow shaft because it lets you put longer stock through the shaft while working with the lathe

[@HaasMill]

It is interesting how were made first rotary parts of the first machine tools in the world like spindles or shafts without using a machine tool

[@johnboyboy919]

Ummmmmm this wasn't supposed to work But mans has a lathe 😮

[@Neally]

I was as shocked as you when it actually worked 😂

[@PharaohMoan]

Do yourself a favor…just BUY the lathe. You’ll never get the rigidity you need to cut clean, and the “chatter” it’ll make, especially without a spindle and center, will rattle all kinds of shit loose, ruin your workpiece, knock things out of alignment, possibly crack welds, etc. And I’m not sure what kind of torque you’ll get out of that motor, but center drilling is a hole other story. I’ve been chasing my tail with a hand-me-down MICRO lathe long enough now to understand I need a bigger/rigid lathe to get the results I want for other builds. Even the $600 or so lathe from HF will perform better out of the box than after all the time and effort you’d have to put into this one. Good luck man, and keep building! #justmytwocents

[@Neally]

Yeah I'll get one eventually, this was mostly just a fun experiment!

[@PharaohMoan]

Was definitely fun to watch also! DIY is sometimes the bane of my existence, but even if things go bad, it’s still pretty good, right?🤘🤣🪓

[@александр-ж1м8о]

Взял и слепил))))посмотрел с удовольствием))))спасибо!

[@Neally]

Thank you!

[@meocats]

Dude i used to do "that" with just a drill in my bathroom and a file in the other hand in my underpants

[@Neally]

Lmao yeah me too, that's why I built the thing xD

[@bridges5659]

Wow ! That's great man. I hope that you are are going to build a guard around that metal chain. I would treat the metal and spray it with high sheen epoxy pain on the frame and other applicable parts . Compliments from South Africa. 👍

[@Neally]

Thank you my friend!

[@alfaxx2509]

Mucho plano, poca explicación, hay mejores videos.

[@Neally]

I'm still learning, I'll do better next time!

[@stefaninilopes4756]

It looks very interesting ! Where are you from?

[@Neally]

Canada!

[@fouadmeddah2790]

Mann deserve the Ultima-Gizmo-lord title

[@Neally]

Much appreciated, friend!

[@جمالزيادة-س7ر]

xtreem well done

[@MECANICA_NA_GARAGEM]

Hello instead of using bicycle transmission, it uses auto timing belt. tempering pieces is with water, the piece must receive heat until it is between red and bright red. then let it cool for a few seconds to lower the temperature slightly and submerge in water. do the test with a piece of metal, bar, axle... the same material in water and another in oil.... then try to file

[@Neally]

I will be using a belt in the future. I heated the pieces to hot-blue them, not to harden✌

[@sarahbear5578]

Awesome video, crazy creativity ☺️☺️

[@Neally]

Thank you!

[@Pippy626]

Anyone have the actual plans for this?

[@Neally]

Nope, I don't have them anymore

[@fladoodel]

To harden those gears you should have got them red hot and held them there for a minute or two before quenching no hate just saying. I hate how people on KZbin are like if it's not perfect by the books it's garbage so I don't wanna be that guy, looks like this lathe is useable

[@Neally]

They're made from mild steel so they wouldn't harden up much anyways, I only did it to hot blue the steel for rust prevention purposes. And yeah I agree, it's definitely not perfect, but it does accomplish what I needed it to. It'll do until I get around to making a Mk.II version😂

[@datuaria9002]

Here’s your sub bro, keep making content like this. Stick welding and scrap material, Couldn’t relate more🙌🏽

[@Neally]

Appreciate it, boss!! There's more on the way soon!

[@arsenioegoytorogiguinat2826]

what is the purpose of that copper tube wrap in the motor?

[@Neally]

It's a cooling system for the motor, I had overheating issues in the past

[@Soulliom]

I've seen you've been replying to recent comments so I wanted to ask a few questions before I attempted this at home. 1. What is the thickness/height of the steel tubing you used? I have some 1/16-inch thick and 1.25-inch tall tubes, but I'm not sure they will hold up to the task. 2. What tolerances were you able to achieve with your build? +/- .1-inch? 3. Why was the framing as long/spacious as it is? Such as the area where the motor sits? Or how high the chuck lies from the base of the frame. I'm in the process of making a smaller version with many of the design concepts you've used, as they are (scuffed yet) beautifully simple. The only complaints I have are how there aren't any shots at the end of the video with the build fully complete, or a list of the materials you used. Other than that, really awesome video and super inspiring. Thank you.

[@Neally]

1: I don’t remember exactly, but I think it was something like 1 1/2in with 1/8 wall thickness. 2: I never bothered testing for tolerance because of how much variability there was right from the start. It could be as bad as 1/16, close to the chuck, with it worse further out. 3: The extra space was for a tailstock that never ended up getting made. The primary thing I’d do differently if I could go back is to make the rails have angled sides to act like dove tails, same thing on the cross slide. Hope this helped, Neally

[@Soulliom]

@@Neally Hmm, I guess I'll try with my 1/16 inch thick walls and add some extra framing to keep ot rigid. Hopefully that goes well lol. Also, 1/16 inch tolerance really isn't even that bad for a project like this. But it sounds like the concentricity of the chuck is off, which could either be a big or a small issue. When you mentioned dove tails, did you mean angling the framing that the carriage slides on by 45 degrees? What difference do you think that would make? Thanks for the super quick reply man, hope all your future projects go well!

[@Neally]

The way my rails are set up makes it so that high pressure on the slide will lift the slide off the rail, I counteracted this by putting tension on the lead screw, but that creates its own issues. If you make your rails so that they are angled you are able to tighten the fit of the slide on the rails creating a drastically better fit, look up dovetail lathe ways on google, I guarantee it’ll save you a headache or two😂 Take care and good luck!

[@Soulliom]

Ah I think I'm picking up what you're putting down. Ill definitely keep that in mind. Thank you so much man!!

[@sharmaruggoo7679]

Well done bro. I like the video only mechanical engineer will understand your idea and project

[@Neally]

Thank you very much

[@Mpm-bu4gy]

JESUCRISTO TE AMA

[@nellykarron8086]

An dir geht verloren ein guter Schauspieler ! Gut gemacht !

[@deskmat9874]

How much did this project cost??

[@Neally]

I'm not ever sure anymore, I think it was around $500cad for the metal and hardware, and about 80 hours of work to put it all together. I should have just bought my mini lathe to begin with 😂

[@chkarron]

You are incredible

[@Neally]

Thank you so much!!

[@mockyhachibondo1580]

Great

[@zJericho101z]

This lathe is sketch as F"£k but i love it.

[@Neally]

Yeeah I nearly shit myself the first time I turned it on😂

[@ojobreaker7743]

You need to cover that chain and/or put a emergency stop on that thing. That thing is cool but way too Easy to hurt yourself.. Atleast put some kind of plate/board on your side of the chain to protect yourself and anyone in the shop from getting a finger or more blasted acrossed the room pls

[@mattparker1390]

Holy shit, thought you had 100k subs easily. Great job. Good video!

[@Neally]

Thanks!

[@DMNTek1984]

BTW, конструкции катастрофически не хватает жёсткости. Необходимо выровнять станину и добавить дополнительных рёбер жесткости. Также было бы неплохо использовать трубу без продольного пропила в узле крепления подшипников вала. Также не помешала бы самая простая задняя бабка с самым простым конусом на подшипнике. Это значительно увеличит качество обработки и повысит точность. Лично я бы ещё использовал не цепную передачу, а ременную, т.к. это исключит риски поломок в случае застревания резца в заготовке и снизит количество используемых деталей для передачи, что повысит надёжность и КПД системы. I am too lazy to translate all of this, so pls do it by yourself. It will be more accurate, than my own or online translation. Have a nice day!

[@user-pu2zp2ke2l]

Paradise

[@adrianakuzmikova1697]

how long did it take you to build it?

[@Neally]

About 10 8hr days, give or take

[@rossideas5884]

good job man 👍👍👍🛠

[@Neally]

Thanks 👍

[@flyback_driver]

4:55 man I am crying I can see that wobble from here. Jokes aside very well done man. Hey I wanted to add a few things that might be helpful. If you do turn crankshafts or anything that will require really tight tolerances I would take really shallow cuts until you are certain the maximum runout your machine has. Also, while chain drives are very good at not slipping you actually want the opposite on a lathe. If your belt is tensioned correctly it will only slip if something goes horribly wrong. One thing that can fix some of the runout would be replacing that needle thrust bearing you heating with a new one. Make a jig to install it perfectly square on the shaft and if it's a tight fit either freeze the shaft and then try or have it press fit. Other side of that coin is the chuck was welded on which added some distortion. I really like what you did with that bench grinder motor. Mine always got way too hot and I actually rounded a small radiator from a window ac to pull heat from mine but your method seems much easier. Still very well done man . Last thing I promise you can used a start capacitor with a little more microfarad to give that motor more of a lunch when starting. Please, be careful spinning that be hand it will take your finger like nothing.

[@lewis6747]

The fact that your bearing is purple-blue, means that you have heated it too much, its life will be more limited, Away that, bravo for the job done !

[@Neally]

I'll be rebuilding the spindle in the spring. the bearings were mostly temporary

[@lewis6747]

@@Neally Ok well done !

[@AnnelyKarronArt]

I love your videos, keep it up!

[@Neally]

Thank you!! Will do!

[@chronokoks]

jankiest self-made lathe on youtube. But it took guts to build it. Silver lining :D

[@Neally]

Lmao I'm gonna take that as a compliment😂It does what I need it to do, so for now I'll say good enough

[@Timothy271279]

Good job 👏

[@Neally]

Thank you! Cheers!

[@mughalmirza2349]

Yor are very talent and genious

[@Neally]

Thanks boss!🙏

[@IvanJardine]

Great. Don't pay any attention to untalented detractors. I think you are definitely a genius, no kidding. I knew, as you did, that by using the materials and tools you had on hand that this machine was not going to be incredibly precise or powerful. But, it is incredible; a very handy tool for turning down stock. If you need super precision for a project you can always take your stock to a machine shop. I think you should have taken the pipe to a machine shop and had the ends turned down for a good bearing fit though, it would have made it run truer. Also, don't heat a bearing any warmer than 150 degrees Fahrenheit, that should be lots to slide it on a shaft at room temperature, without damaging the bearing. Again, excellent work!

[@Neally]

That is greatly appreciated, my friend. Thank you and have a great holidays!

[@eric99vigne]

C est bien

[@witchyphil]

Can I suggest a solid shaft and pillow block bearings for a more true turn.

[@DIEmicrosoft]

Dave Gingery has a great series of books on this type of thing. Check it out.

[@aserta]

Two things i'd change to the recipe 1. rigidity 2. rigidity Basically A frame for the spindle bearing supports. Not a box frame. That's not only not rigid, but it's also something that can build resonance. The riser for the tool block, that'd have to be more rigid as well, with a wedge put inside (there's a woodworking channel that built a cheapo vise, and that's how he did his vise jaws. Tube + wedge inside - aka triangle). Finally, the ways of the lathe, i would build them in a triangulated fashion, as close as possible to straight (but i wouldn't put too much effort into it at first) and parallel. I'd also make them such that the "legs" could be buried inside a large concrete block that spans the width and length of the lathe. Once those are in set, to make things parallel, square, even whatever, i'd choose where cuts could be made from the sub frame (the concrete) and before making the cut, i'd weld a nut and a plate and cut between them. That way, if you want to tighten or expand that joint to brings to even, you can use a bolt to push or pull based on its position, before welding the cut back. All welds done in this operation would have to be very quickly chilled, so a wet towel should be in place. This could yield a bigger lathe, on the cheap.

[@Neally]

That's a good idea, I like it! Cheers!

[@saeedmoghadam45]

Hi bro.can u send me shematics and ... this lathe for me please?

[@jahangirkhan8563]

very glad i found your channel. Keep up the great work.

[@Neally]

Thank you!

[@damianmullin]

You are a smart cookie fella and your videos are great watching. Can I ask where you sourced the hollow spindle from...the bicycle???

[@Neally]

Thanks! And it's just a 3/4 x 18 inch schedule 40 water pipe, got it from home depot

[@damianmullin]

@@Neally 😀. Brilliant, I'm probably overthinking everything in my build plans.

[@Neally]

@@damianmullin Overthinking?? I just consider that being thorough😉

[@dikhed1639]

You're wearing gloves so you won't leave finger prints?

[@Neally]

Yep

[@riskakarlita8394]

The cutting result is better than i expected, i though the mechanism, rigidity were suitable for 3D printer only. Good work

[@Neally]

Thanks!

[@CodeAsm]

​ @Neally Thanks for pinning Alex Bucjanan his comment. Me, a 3 year student dropout (to become a Master machinist) was having internal thoughts. I wont share those tho cause after 10 years becoming a programmer, and not touching a lathe anymore... I would love getting into welding and build a lathe myself (or buy... if I have the coin). His book recommendation is on my to get list, welding equipment, and some other tools.

[@Neally]

Oh I had to, his comment was so insightful it would have been a crime not too. I think being able to work on your own terms is incredibly freeing, so definitely go for it, my friend!

[@loganjefford7290]

That was dope man!

[@Neally]

Thank you!

[@chrishayes5755]

dank build 10/10

[@Neally]

Thank you, friend!🤘

[@jellabean]

I wish I had the tools and space to make fun stuff like this.

[@Neally]

Giver a shot if you get the opportunity! Definitely worth it

[@cesurkomando5335]

Güzel iş

[@Neally]

Teşekkürler!

[@dalirose9065]

Wow! After watching you make this all on your own, I’m feeling much more confident that i cannot make my own lathe and i will be going to Harbor Freight as soon as the beer fund is refilled!

[@Neally]

Yep, I think I should have done that from the start 😂

[@TomsonDesign.]

Very good job

[@Neally]

Thank you!

[@gmendes1831]

Nice job!

[@Neally]

Thank you!

[@__DZ]

Great job

[@Neally]

Thank you!