How to Assembling LM317 Adjustable Voltage Power Supply KIT DIY

[@LawrenceDuffy477]

Awesome video !!!! I like the way you went through the whole thing, great for beginners. Even little things like a screw driver in the gator clips. Never thought to do that. I'm looking for project kits I can buy. Assemble. Flip. A PCB flipper??!!! LOL. This too time consuming I think. $50 and hour labor, parts, mark up. I'd sell some but not many I bet. Not enough amps too. Stocking stuffer, sure. But that's it. Although the finished project sure is beautiful. $15. Assemble sell for $150 -$200. If I could beef it up to 5 amps. Hmmmm

[@ReparatumismoSPAIN]

Me encanta la caja, felicitaciones

[@janearellano278]

Hi how are you I like it your all maker

[@insanbiasa4931]

my master is creative person..like u

[@BrilloG]

muchas gracias ahora podre armar mi fuente

[@azlannakamoto7913]

This is an amazing kit, cant wait to get my hands on this. 🤩

[@nespk]

i think you are top best of all on youtube.SO therefore i request you to make tutorials on arduino hardware and software from basics to advance level in details.

[@sholimz]

you should actually do the low components first before the towering components.

[@JerryEricsson]

I ordered one of these a couple of years ago, they sent me the wrong transformer and it just would not put out any usable voltage from our 110 volts here in the USA. After some time, I came upon an old transformer that was small enough to fit in the case and rewired that in. Now it works. I never use it, but it does work. I should just toss it or something I use old 18650 batteries for all my power needs. I built one set with a meter that gives me 5 to 12 volts, and another that gives me 12 volts up to 24, and my big boy puts out 24 to 36 volts. As much as I use them, charging isn't a real problem, about once every couple of months I rotate the cells and recharge the ones that I have been using, more often with the 5 volt system, of course.

[@syedsardarali2652]

I like most of your videos

[@CrazxyD3xter]

nice video keep it up all the best for next video

[@conrayjones9290]

you should solder the lowest compounds first working your way up to the larger.

[@omarshambi2569]

I didn't knew that

[@DilchandChouhan-db5xi]

Very good

[@mango3586]

VERY INTERESTING VIDEO THANKS.

[@TheCatCalhoun]

When connecting the transformer to the power supply wires, is that also the same metal used for soldering or is it copper?

[@user-cu9dt4we3d]

Best hy Bhai incubator kit ki koi videos bnaen

[@tivinhatui123]

Bộ Kit này ship về Việt Nam và thanh toán bằng thẻ hay cash vậy bạn? Tớ thấy trang bác đang truy cập Banggood với location cờ đỏ sao vàng.

[@yugandharpandhe4627]

I loved it! you're really awesome creative channel!!

[@PunakiviAddikti]

Very nice device, I would definitely buy one. This might not be suitable for kids though, because of the mains transformer. An adult should definitely connect and insulate the mains power cord. And even then you should know about the danger and never plug it in if the wires are exposed.

[@DollarbillDollarbill]

My kit came with the cord attached to transformer on primary side. In my case I had to change the transformer ,diodes, capacitor ratings, and change the lm317 to lm388.My only real complaint with it was the transformer. The other stuff I changed just because I wanted 3 amps at 13 volts.Yes since your working with live voltage I would think you need adult supervision.

[@lexpee]

Thank you for the nice video. Nice kit, this is a old school power supply with a Transformer. capacity 1.25 to 37 Volt out 1.5 amp max. Nice power supply and charger not expensive. For little money you can also buy a digital DC tot DC confuter this in combination with an old adapter, or old notebook power supply. i have a 10 amp DC tot dc confuter working on a 120W 24V notebook supply.

[@kylethomas6599]

Where did you get your snips/cutters at? 2:50? and where can i buy them online? please reply

[@محمدمحمد-ر4ش3ث]

والله هي روعه كبيرة افضل واحد باليوتيوب

[@DoozyBytes]

I modified mine a bit. I put the display on the front, added a heavy duty terminal on top to connect my wires to and also attached two armature wires on top like antennas that I use with alligator clips like a helping hand/power wire

[@plumixtee3496]

EY how did you finger got like that? 12:49 Doorsnap?

[@pjsivley]

Plumixtee could have been an extra digit when born, happens to 8-10% of the population.

[@justiceblackwolf369]

Plumixtee i didnt even notice lol looks double jointed , my nieces and nephews can do that

[@christianmarin3659]

muy buen regulador amigo buena precentacion me gusta

[@gaz58ka_oregenal]

Оогл7л786щшщ

[@stephanc7192]

What are the other inputs outputs?

[@LampuLedPLTS]

nicely boxes and power suplay

[@mrjn5786]

you make me smile mr creative :) i just wonder can i put switch in ac source? :)

[@briandoesstuff4831]

"how to assemble" is what you mean. "assembling" is as you are doing it, like, "I am assembling this thing here" by the way, you make awesome stuff!

[@1claylori]

Parabéns muito bom seus videos

[@uglitor]

What does the different leds indicate? I have the red one on almost all of the time when I power something

[@eduki]

Does it overheat or needs a fan? What to do if you need 3 Amp and 20V. Maximum? Is there any kit available?

[@frankvanmierlo9818]

Does it matter which blue wire you connect to which hole?

[@trvenugopalan2800]

Thanks.can u pl.tell where I can buy

[@YoutubeparisnewsBlogspotFr]

Thank you very much for this video I will soon receive the ""60knobs bastl instruments""" and I hope that to weld everything goes well because I have never done this before.

[@aguswidi9316]

Can you tell me what is the three blue output on the left? when i tested to use it the buzzer rang. Please tell me

[@Turjak_art]

For what is the red and green led? thank you for sharing

[@jaytee3472]

i would also like to ask that. what is the purpose of those led

[@baders2738]

👍👍 very nice

[@Dawid-jt4wr]

I will buy this i from poland :D

[@bhupendradesai2956]

please reply my previous comment and voltage adjustable is a stabilizer? difference in price between ready made n kit assembling what is price of kit

[@yeshecan7]

hi creative chanel, please try to do and show us how to make a mobile charging by using Capacitor. thanks a lot about your chanel.

[@Drxxx]

nice project..

[@sunrising6488]

wonderful work

[@clark2711]

Can current be adjusted in this kit?

[@spydygaming192]

very cool !! I have one myself which is fed to 220-230. But mine has no light. Adjusts the potentiometer potentiometer has around 10K My source voltage 20 volts out Between the two amps

[@sadi3230]

Very nice to see .

[@Berghiker]

As with any power supply....What is the max current draw of this one?

[@billmclaurin6959]

Can it be run off the UK's 240V supply or does it need a step down transformer for 110V?

[@MahBor]

It runs on 240v

[@luizbarroca7523]

What for are the red and green led ?

[@herculesgaming9708]

Can I use it for my HP 1710 led monitor?

[@nkmjan92]

bro.. what's the name of background song?. plz let me know!!..I love it.. and great video amigo!!

[@ECrackers]

Is the ic is programable or linear?

[@aatishsawardekar104]

I like that this video 👍

[@garittuggle430]

Can you show applications for the bottom 3 terminals? DSO3 DSO4 AND DSO5?

[@DariusRibinskas]

What is your solder?

[@swapnilchristmas1493]

creative channel plz make a video on how to make a 3d printer at home at a very cheaply cost

[@bhupendradesai2956]

it is stabilizer ? what is use of it I am houseman N b.com person but interest in electronic item have you kit of transmitter n receiver n info price of both these

[@gokhangumus259]

VERY THANKS FRENDS.NİCE PLAY..

[@KaliyanElectrical]

Transformer kitna Ampere ka h bro.......?

[@zipcustoms4584]

Does it come with gpu compound for the heatsink

[@hackeritalics]

I was seeing a ton of comments about the devices power output.. so I thought I'd give a good explanation of why there is confusion. The first thing to note is that you can draw a ton of amps if your voltage is low. If it is high however, then you will be able to very little amprage. For more on this, look at some explainations of "watts". Now, because this is a Linear Voltage Regulator, it has a pretty limited amperage/power output. This is because Linear Voltage Regulators dissipate the energy Dropped as HEAT. This means that, say you have a 24v source you are putting into the regulator. Your load is 3v and draws 1a of current. That would mean that the linear regulator would need to dissipate 21W of power as heat. :( This is 1w more than the chip can handle as an absolute maximum and would very realistically MELT the solder off of the pins it would create so much heat. What you want is going to be something that can drop the voltage without dissipating that energy as heat. You need something that can simply switch the power on and off thousands or 10's of thousands of times a second to a ratio of input voltage to desired output voltage, where it can then be smoothed by something like a capacitor. :) This is called a Boost converter. :D Take a look at some videos on this! I recommend the videos from AfroTech where he talks about linear voltage regulators and boost converters in depth. A boost converter can be upwards of 95% efficient, meaning it only has to drop 5% of the power as heat. You can buy cheap boost converters at amazon/ebay/bangood for only a dollar or so, then stick that onto an old power brick that you have lying around. Solder some wire and a larger, case-mountable potentiometer and then a cheap multimeter module from ebay/amazon/etc (about 3$) and you have yourself a very very capable power supply that will be able to output 1a at 18 volts no problem! If you just search youtube for "boost converter power supply" you will see a ton of examples of this sort of setup. :) I hope all this helps!

[@okan3644]

Thanks for the info dude! Appreciate it^^

[@mohamedyousif1986]

Can I contact you please ,for help I do same project but I face problems

[@carlovelasco6343]

bro is this good to use as voltage injection tools on motherboard repairs

[@sidramsaybane3353]

Sir ye apka order kitane dino me Aya Aur ye 230 v par chalega na kyaki order par likha hai 110v Plz bataiye sir plz

[@akshayshakya9001]

Can I use this for tv

[@jamescolby3956]

is there an american power version of this id love to try it but need the 120 240 here in the us

[@captainkiddoregon]

www.banggood.com/DIY-LM317-Adjustable-Voltage-Power-Supply-Board-Learning-Kit-With-Case-p-964548.html Just received mine tonight.

[@alien1898]

Are you soldering with your yellow glow plug 12 v homemade soldering iron?!?

[@JakeJoris]

good video

[@relipe1979]

O meu depois de montado liga o led azul mas não liga o display e nem sai a voltagem DC nos fios preto e vermelho. Será que é solda mal feita? Como eu poderia identificar onde está o problema?

[@abduljabbarkhan7046]

I wanted to know that which is a shopping site where I can get IC an6884..because in our area shops it is not available. please help me I wanted to make led vu metre out of it

[@roysingh485]

Hi where can I buy the kit

[@justgame5508]

Nice video I used this same kit but changed the case and added a current limiting circuit before the voltage adjustment circuit and a display to read both current and voltage

[@takerkanefan108]

Can you make a video on turning a computer power supply into a power supply

[@LesTutosdUneMinute]

I made one of these, works just fine

[@davebuts1921]

That is easy mate just connect the green and a black together and that's it. You can go for what ever size you wish. Mine is 550 Watts PSU, use what ever size and power you need. Then you get What my 550way PSU gives me Ground Black wires 12 Volts @ 26Amps Yellow wires 5 Volts @ 29Amps Red wires 3.3 volts @ 28Amps Orange wires -12 Volts Blue wire -5 Volts White wire As you can see its a good size Amps for a cheap PSU Around £25.00 UK Would be happy to put a vid up, have a few power supply hanging about. Regards Dave UK

[@etro8564]

You have a green wire on the 20 pin connector and connect it to one black wire on the same connector and plug the power supply in and you can get it working with diferend voltages!

[@etro8564]

+davebuts you can even get 18 volts if u combine wires together 😊

[@davebuts1921]

You can get all sorts of volts if you wish, but all I need is 12 volt and the 5 volt, I do keep the 3.3 as well. Its a cheap bench power supply with high amps

[@jaymekg6236]

Did this order come from China?

[@anonymousgaming1995]

will it regulate 24 volt dc if i give it from any other source

[@etro8564]

When banggood ruins your life 😂😂😂

[@ChannelCreativeVN]

haha :))

[@santiagoporra2341]

👍👍👍👍👍👍👍✋✋✋✋✋👍👊👐👐👐✌✌✋👌👌👌👌👌💵💵💵💵💶💴💵💵💵💵💰💰💰💰💰💰💰💰💸💸💸🔔🔔🔔🔔🗿🗿

[@a0925280852]

Etro

[@valeriorosati5657]

ok

[@MazookDK]

Or Wish or eBay 😂👍🏼

[@skillradius9867]

In how many days banggood delivery comes to ur house

[@myclipsnew5361]

Hi , can you Please build somthing for Holding the PCB when ur Working on it? Thanks

[@michaeljamora7595]

hey dude? this power supply can powered car amplifier?

[@divingquokka]

Nope. It has an output of only a few Watts. For a car amplifier you will want something beefier.

[@WhoWantsToKnow81]

Unfortunately the LM317 is extremely inefficient when it comes to a large differential between Vin and Vout and the required current load.... I recommend a SMPS (switched mode power supply) instead.

[@tahnjr]

WhoWantsToKnow81 : Even a switched mode power supply, should have a linear output regulator for benchtop circuit prototyping.

[@HappyHermitt]

Good enough for MCUs and such.

[@francescogiaccio6733]

What is the name of the first song in this video? Thank You

[@vishnumpvishnump4510]

What material used to case

[@kamranafzal1469]

Please come live sometime

[@nespk]

why don't you make videos and projects and specially tutorials about ARDUINO?

[@nandexlao2653]

ผมชอบมากๆๆๆครับ

[@นพกรดวงสม-ง4จ]

นายก็ดูช่องนี้หรอ

[@nandexlao2653]

+นพกร ดวงสม ผมดู ตั้ง แต่ นานแล้ว ผมไม่ ก้าc.m เท่าไรเพาะไม่เจอคน ปะเทดตัวเอง เลีย

[@nandexlao2653]

+อาร์ เซน่อล 55555

[@puriwatw.1323]

ตัวนี้มันเอาไว้ทำอะไรเหรอครับ แล้วมันปล่อยไฟกี่แอมป์

[@jon_918]

will it work on 240v ac ??

[@debojitacharjee]

i want to know how do i know the amps of a battery if i want to power any electronic device intead of a power adapter. For example if a device needs 3v 0.4 A power adapter then how am i going to know how many amps two AA 1.5 v battries are going to give if connected in series? I know that in series both of them will give 3v but how do i know about the amps because all types of batteries are not having same ampere hour ratings!

[@debasishchatterjee8094]

do you have any problem getting the package from banggood

[@lordbuddhaselectronic4501]

Kitne amp ka load le sakta h sir

[@baptistegear]

How do you know the positive and the negative sens please ?

[@etro8564]

Red and black 😂

[@baptistegear]

Yes thanks ! But the sens of the first composant for example Etro

[@roushhawley8438]

"how to assembling" other than that, this is a pretty good video

[@davelandis5591]

The instructions in the video has some bad English too. But learning a foreign language isn't easy.

[@johncherry108]

The instructions clearly said "First of all, installation dwarf components , then installation of high components", but the big electrolytic was installed first.

[@LesTutosdUneMinute]

Nice

[@Dawid-jt4wr]

Very goooood ! my friend

[@kavishkaperera9364]

Nice one

[@hamza_n0552]

ill test it out someday

[@sandarbhverma3675]

How much cost of this set,I want to buy one more, send me this set's cost

[@mac2484]

What's the difference between this lm 317 kit and the one u made earlier in a box with voltmeter what's the difference between both

[@imnotbeluga007]

The regulator is the same, but his has way less parts, and it's not on a PCB. But it could support up to 37V, which this kit (probably) can't. And especially, that voltmeter has a separate power wire, so not turned off at low voltages!

[@hanzomancer1635]

Any idea why my voltage display for this kit stops lighting up when i connect it to a load?

[@MahBor]

You’re connecting it to a short circuit

[@-ridder1227]

Are you making a converted 12 volts to 220 volts

[@pratikrane2297]

the output voltage is dc or ac

[@ionutilea7679]

i like you me indpiration i am 14 years i from romania