How To | Auto Transaxle-Output Shaft | Auto Trans Output Shaft Seal | Install

[@timontymcinnis5197]

4 years later and it's still the best video!!!

[@TattsForLife]

Thanks, that means alot

[@AstroTheBalancer]

This is by far the best how to video ever made man, EXACTLY WHAT I NEEDED! You actually showed what needed to be showed man

[@TattsForLife]

Thanks for watching and the comment

[@PREACHERSPROPHECIES]

You are the only person who was able to explain what I needed to do in about 5 min. I am no mechanic but I just fired them 2 and did it myself and all I needed was just a little bit of sylicone lol thanks

[@TattsForLife]

Happy you found this video helpful. alot people think silicone is bad, but as it gets pressed in most of it gets mashed off the seal and what stays is only whats needed if they are bad places where the seal goes or misshapen due to heat depending on what you working on

[@missingremote4388]

Why do my axle make a hum noise? Differential doesn't leak. Transmission is fine. Hub bearings a a year old...

[@TattsForLife]

wheel bearing, or axle nut to tight

[@missingremote4388]

@@TattsForLife yep. I over did it. And had to repair or replace the hub bearing again.

[@TattsForLife]

yah, thats a pretty common thing happens, I see it alot

[@Oskar_Panacea]

Thank you for posting this video! It was very helpful! I had a bit of trouble hammering that sleeve on the stub and I came up with a work around.... I used a tie rod tool you can get at any auto parts store and it worked like a charm. You get more control and don't have to worry about knocking it down too far.

[@TattsForLife]

your welcome, and great info on the tie rod tool trick

[@thadshepard8069]

This was the exact fix that I needed. I did not have an intermediate shaft the way you did and I had to drive it onto the axle. The other three mechanics could not figure this out and with your help, I made them look like fools.

[@TattsForLife]

Thanks for watching

[@MrEmanuelito17]

You safe my life man thanks 🙏🙏👍👍 excellent video🎉🎉

[@TattsForLife]

@@MrEmanuelito17 thanks for watching and taking the time to comment

[@archvizwiz]

never use any type of sealant on any parts unless the manufacturer did while assembling the parts. in other words. if the mfg. didn't use silicon. you should not either. how easy do you think that seal will come out the next time? when you find out your seal leaks?

[@TattsForLife]

Thanks good info, and it never leaked prob because of the sealant

[@adictiveadictive]

Whats that other part for? Needs to be installed as well?

[@dereckbruh8806]

So i cant get the little metal ring off my car, do i need to take the stub completely off? If so how do i do that

[@Bigshoots86]

Those snap rings bend widen every time I try and open them and I can't get my axle back on and for the life of me I can't figure out how to crimp them back smaller

[@jazzysmith2430]

How do i get that inner seal off of the shaft my shaft stayed in the engine but i need to replace the ring and both seal does that seal continue to side off shaft

[@TattsForLife]

sometimes you can use a old shop rag and vic grips to lock on to the shaft and pull it out

[@jazzysmith2430]

@@TattsForLife you did the best illustration with the snap pliers but most ppl don't have snap pliers so if you don't mind I think you should do an example with the info you just gave me nobody on KZbin is explaining this literally

[@TattsForLife]

I will if I half to do the job over again, I plan on redoing the car and paint and stuff in the future on the channel@@jazzysmith2430

[@demandred1957]

@@TattsForLife I'm glad to see you are still active with the video.. I'm up to my neck in a cv axle replacement and doing the seals at the same time. Couldn't find information about that new seal surface for the stub, like how to replace it. Like how you showed that part, but how in the world did you get the old one off the shaft without a press? Did you cut it off somehow? I'm thinking about freezing the whole thing, and pouring hot water on the seal surface to try and slide it off the shaft.

[@randycollens2681]

@@jazzysmith2430buy some

[@y.molina7887]

How you remove the inner small axle part?

[@TattsForLife]

sometimes u can insert the old axle and pull, if not you can hook some vice grips on it and pull

[@frankward8040]

How did you get that small spline shaft out mine is stuck and i cant get the inner seal off.

[@TattsForLife]

@@frankward8040 hooked on it with vice grips and yanked

[@demandred1957]

How did you get that shaft seal off the shaft?!? Appreciate showing how it goes back on though.

[@serpret8549]

can you help me understand what the kit does, because i think this is exactly what im looking for.

[@olenaerhardt7725]

@3:55 How important is how far you go? I installed that small seal (2003 chevy Cavalier), then put the assembly on a new CV Axle, tapped it in, the Intermediate Shaft was locked, but I thought I'm kind of too far with that small seal. So I tapped it in a bit more (exactly how it shown @5:31) and now it looks to me that the distance between the rubber on the seal and the end of the cylinder on which it sits is too small. How important is all that? Can't find the answer in any film. I would appreciate any opinion on this matter. Thank you for the film again.

[@andrewhudson3723]

Nice tip! What kind of silicone?

[@TattsForLife]

been so long since I did this repair, most likely its the silicone called right stuff

[@andrewhudson3723]

@@TattsForLife thanks and keep on rockin!

[@TattsForLife]

@@andrewhudson3723 Thanks and you to

[@gregwhitehead7967]

Right stuff bonds to anything

[@olenaerhardt7725]

@@TattsForLife Is it Right Stuff Gasket Maker (Like 90 min gasket Maker e. g.)? Thank you.

[@JoeyLovesTrains]

what accent do you have, it sounds like a southern American, and a hint of Australian

[@TattsForLife]

what accent? everyone sounds the same down here lol

[@jamesbenton1346]

Maybe deep south Louisiana

[@olenaerhardt7725]

I have a knocking sound in the area of engine on our 2003 Chevy Cavalier. The sound depends on rpm, but doesn't change if you shift gears. So I hope it might be a worn CV Axle on the Passenger side (Right side). When I've replaced the transmission fluid on that car I also noticed, that the part of the inner part of the CV Axle on RS is covered w/oil or smth. Nothing is dripping, but the surface is kind of wet. I think maybe it is leaking CV Axle seal causes all that noise. The film is very helpful for me, especially I received rather contradictory answers on Amazon about those 2 seals. That small shaft @2:15, do you always need to remove it when replacing Right CV Axle. And does it come off by itself when you remove the CV Axle on RS, or you need to make some efforts to extract it? Thank you again.

[@demandred1957]

it usually comes out with the shaft. I have replaced the axles before, but not the seals. that was what I was here for. Hope it worked out for you.

[@Randymoore24]

I have a 2007 Chevy Cobalt that is leaking transmission fluid on the drivers side. When i've pulled the cv axle in the past the axle separated from the shaft leaving the shaft inside the transmission. What is the best way to remove the shaft so that the outer seal and bushing can be replaced? This is a great how to video, look forward to seeing other videos you post.

[@TattsForLife]

can you get a sliding hammer on it? to knock it out

[@nathanielbolden5053]

Good video...but that electrical tape!...🤣

[@TattsForLife]

its duck tape lol

[@mexifin]

👍🏾 well explained video. Thank you 😊

[@TattsForLife]

Thanks for watching!

[@overstandingontherealstory6313]

Perfect example thanks

[@TattsForLife]

You are welcome!

[@lawlor2925]

Some BBQ shrimp, bubbagum shrimp, rice n shrimp

[@TattsForLife]

😱

[@michelelaws8215]

How do I get the old one out first?

[@TattsForLife]

@michelelaws8215 i used a pair of vice grips and yanked it out, if I remmber right, was a few years ago when I made this video

[@THOMASDRELICH]

What size socket was that you used to press on the new sleeve ?

[@TattsForLife]

I dont remember, been a long time since I made this video, sorry

[@jamesbenton1346]

Its a 30 mm because I just did this same job myself this guy explains it great.

[@tristan6905]

Great video mate!

[@TattsForLife]

Thanks a lot!

[@SelfTaughtBeauty]

nicely done

[@TattsForLife]

Thanks, it was not the best video, but it may help someone out

[@SelfTaughtBeauty]

+TattsForLife Definitely! I think it turned out great

[@TattsForLife]

Thank you

[@brianbradley7358]

I have a 2002 Chevy Malibu LS and am replacing both axles and in this video I saw a rod in the transmission where the axle is suppose to push passed to lock into the transmission I've been trying to get the axle to push past it but I'm not sure what I'm doing wrong also from the research Ive done I think that rod is what's callled the final gear and is supposed to be there but I can't get the axle in on the passenger side someone please help

[@JCGible]

I have tried three seals. Did it just like it shows, and if leaking. 😡

[@markdesautelsjr711]

How do you get that out??

[@drtb69]

What if your axle sticks out ...I can't use a block of wood

[@TattsForLife]

you could try a socket or a pair of channel locks that are ioen

[@jerseykillabee]

Nice, thanks man.

[@TattsForLife]

Glad to help

[@ArmandoMartinez-xs9ye]

Thanks verte much for You help

[@TattsForLife]

Always welcome

[@joeysanchez5926]

Ty buddy.

[@TattsForLife]

Welcome

[@10pct2_the_big_guy]

Thanks for taking the time to make a video and fuck the clowns that make fun of you.

[@TattsForLife]

Thanks for watching, its all in a days work lol

[@AnthonyArgent]

How do you get the stub shaft out on the driver side

[@TattsForLife]

It should just pull out, held in with a c clip that locks in and out

[@michelelaws8215]

Sliding hammer

[@TattsForLife]

@@michelelaws8215 great tip

[@АлексейН-б2э]

good day unfortunately I do not speak your language sufficiently for communication .. because I am writing through a Google translator Let me ask you a few questions. I have saturn wue. AQPP 4t45, while the gas is being added, the car does not accelerate fast enough .. can you tell me what it is preparing for? and the second question ... what's the difference between 4t45e and 4t40? with respect Alexey

[@crusher-101]

I think the difference is the year of the car.

[@TattsForLife]

I think your right

[@PatrickDiehl]

Great video. Liked.

[@TattsForLife]

Thanks man

[@RCFlyBoy314]

Omgosh.... the silicone....

[@TattsForLife]

yep

[@nathanielbolden5053]

Thumbs up bro!...

[@TattsForLife]

Thanks

[@romsense]

cool stuff bro!liked😊

[@TattsForLife]

Happy you liked it, was a very simple video

[@romsense]

TattsForLife hi!yeah i liked it.simple but very informative😊thanks for sharing😊have a good 1😎😊

[@TattsForLife]

Thanks

[@bzb3153]

Make sure u use a wag. Then pwess it in.... hit it wid a piece uh wood. And it went wite in

[@TattsForLife]

great info

[@AndrewJohnson-yt1nl]

Look BzB 315, the only people going to see this video are those who are trying to fix this auto problem themselves, and the content creator. We all see it once, maybe twice if ya get stuck. But Tattsforlife will see it far more times. How dare you ridicule someone who is helping you for free. You didn't just arrive here randomly, you had the specifically have a question about something this man took his time to explain and show you in a helpful and thorough manner. This specific transaxle is extremely difficult to find quality videos about. Who are you to say a got dang word about how that boy talks. If your mother hadn't taught you better than that, BzB 315, she must be just like you. Someone who's only way to feel good about themselves is to put someone else down. I'm sorry you weren't raised better than that. I'm sorry your mother and father weren't capable showing you what it really means to be a part of this earth. To be part of what makes us human is to BE human. A human with thoughts and feelings who respects and listens to others humanity. Your a beautiful human, Tattsforlife. I hope that this human here made your day like you made mine. Thank you for showing me I didn't have to buy a $250 application specific tool. May your heart stay calm and your conviction burn fierce. BzB 315, hopefully one day someone gives you a reason to be human.

[@stevemitchell2252]

What is the reason some people talk like that?

[@TattsForLife]

cause it one of many amazing things in life

[@orionsanford4440]

Its called a speach Impediment

[@bradysolaem2467]

Same reason one would put rtv on a push in seal

[@burtonbruning8581]

They have a speech handicap.

[@jazzysmith2430]

Down south we country folks downhere

[@ndnride295]

allright thanks for this wasted a seal, now time to do it right, cool accent too.

[@TattsForLife]

it just takes some time get use to installing seals that way, lol you get use to it when you dont have a seal driver

[@solowrider3356]

It was

[@TattsForLife]

Thanks for watching

[@Atune_TV]

good shit man

[@TattsForLife]

Thanks

[@aaronmenchinger]

It's nice to finally put a face with the voice for Elmer Fudd Looney Tunes character👍 but why is the camera man so out of breath?

[@TattsForLife]

out of shape 😑

[@jamesbenton1346]

Maybe just smoked a big fatty😂

[@chadgray6467]

The worst! Just did this and that it way too deep, he didn't even check for wobble on that thing just randomly hammered on, a 1" deepwell completely lines it up perfectly, that was nooooooo 1" and "dwat siwicone", will just make it all fall off and fall apart.

[@bradysolaem2467]

Oh no please stop hell nah

[@TattsForLife]

Huh

[@Pkproduction217]

Wag

[@TattsForLife]

😑