How to automate solenoid valve using relay and Arduino with AC220V Coil(Full tuitorial with program)

[@sorinciolovic9391]

Hello Pranjal, You presented a good and nice project. I liked your kind voice and good explanations. Thank you very much. Kind regards, Sorin.

[@ericobenaus9466]

Hi, thank you for the great tutorial. I'm building this same circuit to control a solenoid valve. I've seen that usually when using a solenoid valve, a snubber diode must be used between the 2 wires of the solenoid valve to protect against back emf. Do relay modules already have a diode built in?

[@pranjalkalita1140]

Thankyou brother. I guess you should put a diode.

[@bharathrk8987]

Since, this is an AC Solenoid valve, I guess you don't need to put a diode. Even I tried the same without fly back diode and it works fine for me.

[@plushy_ducky]

Hey man, great work on automating the solenoid using the relay. I was wondering, if it was possible to connect buttons to program the duration of the valve activation on the arduino onspot instead of having to connect to a laptop every time? Imagine, you need to activate the valve for a duration of 3 seconds about 10 times, with 10 seconds in between. And then after that, you wanna push a button and the duration changes from 3 to 6 seconds, and then it repeats the process for 10 times, with 10 seconds gap. What all extra equipment would i need for such a case?

[@ayateleb9414]

How do you simulate solenoid valve for proteus programm?

[@afrozalam9840]

Sir, Thanks for this excellant video, Your explanation & Demo made me understand the the connection method crystal clear. This is for single coil solenoid but i want to know how to connect 2 coil solenoid valve, if you can spare your valueable time & valued knowledge for an unknown person like me, As we can only give you our prayers & well-wishes in return other than anything.

[@pranjalkalita1140]

Thankyou, its means a lot.

[@profrefaey]

how fastly this valve and relay open and close? to get small flow?

[@pranjalkalita1140]

You can control this with the help of Arduino Uno in your computer

[@sydipopcorn939]

such a good presentation❤️… but your yellow cable colour just makes me confuse all the time

[@JasPer22996]

Hey i love this video. Very informative but I have a question. Do u think its safe to use that kind of relay in 24V DC solenoid valve?

[@yogeshpatil2635]

Does it work wirelessly from 4 km distance??

[@furtherishere7568]

Can I use multiple drip water valve to one ardrino

[@vimal6814]

bro is solenoid valve withstands the air pressure after the valve is off condition

[@pranjalkalita1140]

Ya....If no power is supplied to the valve, it allows the air to flow through another port, when switch on, as the magnetic field generated to attract the plunger, it allows to flow the air through another port. So, it's not like that when it is turned off it will not withstand the pressure. ( but there may be a limit up to which the solenoid valve can withstand pressure ). clear ?

[@bachelorvlogs3645]

Bro pls tell me...how to connect IR sensor with the aurdino..does the program changes when I use ir sensor...pls tell me broo

[@homemadeproductions7175]

which wire is which on the solenoid to the relay

[@pranjalkalita1140]

I have explained this in this video.

[@dysproghoul]

Send the link of the code

[@nandhinijagadeesan3835]

If i am using two solenoid valve means, how to connect them with a single power source? can you tell the circuit connection?

[@krishnatiwari8849]

Which type of solenoid valve it os normally open or normally closed?

[@pranjalkalita1140]

It's a 5/2 way solenoid valve.

[@nithinkumardatti5846]

If I connect pneumatic double acting cylinder, it’ll open and close?

[@pranjalkalita1140]

It is for double acting only. Just follow the process. You should choose right solenoid valve for double acting cylinder.

[@reyasali9788]

Good work bro keep going with new tutorials just like this

[@pranjalkalita1140]

Thanks brother for you inspiration. It's means a lot .❤️

[@nandhinijagadeesan3835]

for 24v dc solenoid valve..how much voltage relay should be used in arduino mega??

[@pranjalkalita1140]

5V relay is enough. Relay is just a switch.A 5V relay can operate a solenoid valve of 24V DC and can draw upto 10 Amps.

[@akashp9766]

Bro i have type the coding that you have shown in your video but after verifying it showing "ERROR COMPLING FOR BOARD AURDINO UNO" why bro. But i have not conneted to aurdino board during Verifying

[@pranjalkalita1140]

You should execute the code when Arduino is connected to your pc. And check the code properly is there any mistakes.

[@honeysingh-yk1xb]

i want complete sketch to operate 8 relays with all different timings , can you compile sketch for me on hire basic

[@maniksharma5877]

Can we use this set up to operate double acting cylinder ? And can you please draw a circuit diagram with proper symbols and illustrations. Thanks

[@pranjalkalita1140]

It is for double acting cylinder only

[@ManasKhare]

hey bro please mention the relay and valve model no.

[@nusret294]

Can i control ac motor 240v with relay ?

[@pranjalkalita1140]

Ya. ....relay is just a switch

[@mulusewyilieyoutube5493]

good video...….. how can I get solenoid valve library?...can u help me

[@akashp9766]

After coding whether the aurdino should be connect to laptop or disconnected from laptop?? While operation of pneumatic cyclinder

[@mithunraj9943]

Arduino needs power supply

[@armandovelez2016]

Hello my bro, how do I connect to a DC battery multiple solenoid vaulves? Keep it up!

[@akashp9766]

Where to type the coding of aurdino bro

[@pranjalkalita1140]

Download the software of Arduino Uno in your pc. Type the code and execute.

[@PRATIK24ADARSH]

Good job man

[@brbeniwal8400]

sir meri machine ka automatic panel banvana hai

[@syafiqahzawanah3814]

Hi can i use DC12 v solenoid valve for this project ?..

[@pranjalkalita1140]

Obeasly you can use, just supply should be dc or Ac with an adapter.

[@syafiqahzawanah3814]

hi instead of adapter can i use battery ?

[@pranjalkalita1140]

@@syafiqahzawanah3814 ofcourse you can use.

[@syafiqahzawanah3814]

hi for the adapter can i use laptop charger

[@mohammadafran7615]

Bro please upload DME 2.... design of journal bearing problems please 🙏...

[@ennaiarindhal3141]

Can you share circuit diagram

[@lennymachika6304]

Please share the circuit diagram

[@aaronharis2008]

Well explained 👍

[@pranjalkalita1140]

Thankyou so much

[@deveshkedia2548]

Please give the list of parts

[@pranjalkalita1140]

A 5v single channel relay. A solenoid valve of orifice size (1/4)" with AC 220 V 10 A coil and Arduino Uno. To connect it with a laptop you need the cable.

[@amalkumar3430]

Sir, can you please provide the code in description 🙏..?

[@pranjalkalita1140]

Code is already provided in video. Execute the same with the little changes in time as you required.

[@tayabfarooq7544]

Awesome man!

[@pranjalkalita1140]

Thankyou

[@ayushsuthar9202]

Aa circuit kya thi lidhi

[@pranjalkalita1140]

Please ask in Hindi or English.

[@yaserzahiri8292]

very good thanks bro

[@pranjalkalita1140]

Welcome brother ❤️

[@Pampi_Sarma]

Its helpful..thnk u

[@pranjalkalita1140]

Thanks

[@summerWTFE]

Thanks!

[@ayushsuthar9202]

Hi bro please help me

[@pranjalkalita1140]

Ya tell me brother, what can I help you ?

[@ayushsuthar9202]

Where did this circuit come from?

[@ayushsuthar9202]

I also have a project of pneumatic cylinder in which I have to control the solenoid valve automatically so I also saw such a circuit.

[@furtherishere7568]

Very nice ,I want this method to implement to drip irrigation valve ,please guide me how to start ,I'm software engineer, I have no knowledge In electronics, give me your number

[@elvinmee]

Hello bro please how do I contact you I need your help with a project