Today we're breaking in our Brand New 2020 Suzuki DF300 outboard motor. I'm going to show you step by step how this procedure is done.
Пікірлер: 78
@dinacaldwell75224 жыл бұрын
I just love your accent and your English is simply fantastic. Great video with great patients taken on the motor so you can enjoy it for years to come
@captainvasiliy43584 жыл бұрын
Thank you Dina
@thebigmann253 жыл бұрын
I would actually advise against what you were doing. You don't want to run a new engine at the same rpm for too long, you should vary the revs. Even if you don't want to go over 3,000, you should cycle between 1000-3000 during that time.
@nomis90523 жыл бұрын
So you would advise him to go against the owners manual and the team of engineers that spent 1000’s off hours designing and testing the engines before they hit the market voiding his warranty when he goes for his first oil change and they hook it up and see the read out on the engine rpm vs hours?
@thebigmann253 жыл бұрын
Nomis The manual doesn’t state run it at the same rpm for the entire time like he did. It’s saying don’t exceed a certain rpm. It’s basic engine knowledge that you always want to vary the rpms on a new motor
@starshiptrooper75203 жыл бұрын
@@thebigmann25 I’ve just checked the latest Suzuki manuals for the 200 and 300hp. According to the manuals, neither of you, (or the guy who did the video) are correct. The manuals state that for the remainder of the first two hours, you run the engine at UP TO half throttle (3000rpm). For the third hour, you run the engine AT 4000rpm. (My capitals). Not sure if this is Suzuki’s intention however. There are a number of errors in the manuals, most likely because the engines are made in Japan and the person that wrote them is probably Japanese.
@captainvasiliy43583 жыл бұрын
I’ve done exactly how Suzuki suggested in the Owners Manual
@starshiptrooper75203 жыл бұрын
I’ve just checked your video again. Your manual says the same as mine, (2:49 and 4:55). “Less than 3000 r/min” and “at 4000 r/min” is what it says. It does not say, “at 3000”. As I suggested earlier, this subtle difference may not be what Suzuki intended. Something may have been lost in the translation. If I had to guess, I would say the “at 4000 r/min” should also say “less than 4000 r/min”.
@jiggsj54733 жыл бұрын
Appreciate the simplicity of your presentation. Well done. Thank You. Smooth sailing, tight lines.
@alansteinle76323 жыл бұрын
Great video! Thanks for some good info. One question. During the last stage of break in how long between 5 minute intervals at full throttle?
@chrisgold89693 жыл бұрын
nonsense....Evinrude all engnes no break in period...
@gordonmohr22682 жыл бұрын
havent you heard? evinrude is dead. no more. gone.
@Eluderatnight2 жыл бұрын
@@fastwin493 I love older OMC for reliability/serviceability, but suzuki is the better motor. Although they did get a lot of tech from OMC/Johnson. In their current state they are the most fuel efficent engines.
@ekimandersom44782 жыл бұрын
No engine needs breaking in. It is all bullshit.
@user-nt9nd7xm5f3 жыл бұрын
Excellent video thank you, just in the process of purchasing a Suzuki DF250AP for our 7.6m RIB down here in the BVI, looking forward to taking it out for a spin
@Александр-я9е4я9 ай бұрын
Какая максимальная Василий)) у твоего комплекта?
@jerimahjohnson86984 жыл бұрын
Got 2 new df200 on 26 world 🐈 Getting ready to do this
@t268033 жыл бұрын
me too on a stratos WA
@dailystruggle2762 Жыл бұрын
How to break into the motor? Just open the cover…???
@ЕгориусПомидориус3 жыл бұрын
Можно по русски?
@bryanoverton46753 жыл бұрын
Just picked up a 2020 SeaPro 248 DLX. Suzuki DF-300ap. Getting ready to take it out and break it in. Great Video. Thank you.
@joed13194 жыл бұрын
What size boat do you have, who is the manufacturer? Great video btw, thanks for making it since I'm looking to buy the same motor.
@captainvasiliy43583 жыл бұрын
Sorry for late answer, this is 2016 Sailfish 240CC
@ЕвгенийШалимов-щ1и3 жыл бұрын
теперь бы на русском ещё
@mmiguy11224 жыл бұрын
I was told to not run it at wot long for break in. Nothing so specific. Im now experiencing cavitation and its taking slower to plane out. Dont know whats wrong.
@Sour754 жыл бұрын
Nod and smile at sales staff. Then, read the manual and do EXACTLY what it says. Every time.
@captainvasiliy43583 жыл бұрын
Try different prop one pitch lower
@nospamful2 жыл бұрын
I just saw this video. Hopefully you're problem is sorted out. I saw a KZbin on a new boat they put on the water and they mentioned that the motor needed to be lowered because they were getting cavitation. See link at about 4:18 kzbin.info/www/bejne/hZ7aY2mYpNSoe5o
@WillemLuntungan3 жыл бұрын
Thank you motor Boat
@sea_knot Жыл бұрын
Хз. Я бы на всю котлету сразу навалил.
@brandonmurphy46573 жыл бұрын
My dealer told me to run it
@buckrockerm3 жыл бұрын
Smoke it if you got it!
@ct1762 Жыл бұрын
i highly disagree with this gentle/extended idle approach. First 5 minutes idle, then full throttle to plane the boat off, and back down to half throttle - 3/4 throttle varying the speed every 30 seconds or so for about 10 minutes. back to idle. shut motor down. let it cool off. then start it up and go full throttle for 1 solid minute, then back off varying the throttle a bunch. thats basically all it takes to seat those rings, and thats all you are doing. nothing more. too much idling will cause the cylinder walls to get more of a glaze than is optimal, and it will start to burn more oil after 500 hrs.
@idahobob180 Жыл бұрын
Did you say 7hrs at full throttle
@gnrfan32 Жыл бұрын
"Up to full throttle for no more than 5 minutes for the last 7 hours"
@jzl300z4 жыл бұрын
Any update on how you like it so far compared to the F300?
@captainvasiliy43583 жыл бұрын
Now is about 150 hours on it, the motor is pretty strong, better on MPG than Yamaha F300, as well on cruising and top speed.
@scottvickery2057 Жыл бұрын
just out of curiosity, why did you not replace with another Yamaha?
@JhonnyBravo223 Жыл бұрын
With 50hp honda 4 stroke, carburation, i race that motor eazy
@jamesjannell87062 жыл бұрын
I have new suzuki coming in May and found your video very helpful thank you. Off topic question for you, who makes that hat you are wearing ??
@ibyisabeast3 жыл бұрын
how does it compare with the yamaha 300?
@valentineayuk92982 жыл бұрын
You can get your Yamaha in all years from this guy I got entangled with and he’s stuffs are awesome
@valentineayuk92982 жыл бұрын
@Andersonera
@valentineayuk92982 жыл бұрын
He’s on telegram
@sea_knot Жыл бұрын
Эх Вася, Вася!
@gregwilson5902 Жыл бұрын
Hey great video. Where can I buy that hat?
@meteergun343 жыл бұрын
👍
@brianlee68492 жыл бұрын
What about the first oil change? Do you do a break in oil change? I know some engines the first oil change is early. How many hours does Suzuki want you to go on the first oil change? Thank you 👍
@qcollins18412 жыл бұрын
20 hrs
@demirel19754 жыл бұрын
The best break in video, thanks
@captainvasiliy43584 жыл бұрын
Thank you man
@cedricjeangoudoux90542 жыл бұрын
Whats propellers ?
@LarsonFishing3 жыл бұрын
I was only able to get into the 1.45 hours at 3K R/PM and had to pack up for the day. Can I finish my last stage of 4K R/PM in the morning like I had planned? for the most part I stayed at 3K for 1.45 hrs with maybe 10-15 minutes of reduced idle all together in that whole time, is this also ok? Thanks!
@ct1762 Жыл бұрын
you are way too gentle with the motor! they dont like this gentle approach. after 10 gallons of gas, if you varied the throttle a whole lot and plenty of full throttle runs, the rings are seated. DO NOT give it any more extended idle. this is why these motors burn oil after 500hrs: cylinder walls glaze up and wont seal the rings properly.
@donnie49954 жыл бұрын
I have a 18ft palm beach whitecap..do you think a 90hp 2020 Suzuki would perform ok?
@captainvasiliy43583 жыл бұрын
In my opinion please talk to your Suzuki dealer, I’m not familiar with this boat