How to Break in an Outboard Motor | Mercury Marine | 2021 | 150 Horsepower | Four Stroke

[@gregshaver1265]

Thanks for the vid. Not many up to date on here. Just ordered the same boat two weeks ago. Can’t wait but sounds like end of June delivery. Did you get a top speed reading?

[@TheOutdoorConquest]

Hey Greg thanks for watching! I had it out this weekend with a half tank of fuel and 3 grown men on it and I topped it out around 40mph according to the boats speedometer. Really haven’t had any issues with the the boat as a whole. I’m really liking it!

[@gregshaver1265]

Beauty! Thanks for the reply

[@luiszamora9256]

Thanks buddy, i followed the same steps. Mercury 115hp 4 stroke.

[@TheOutdoorConquest]

Nice! How do you like it?

[@robertwalker9211]

Great job sir 🎣🎣

[@TheOutdoorConquest]

@@robertwalker9211 thank you!

[@sgtcote1]

Thanks Greg I just had my new 75Merc installed onto my 1989 16ft Mirrocraft. Hopefully in a few weeks our lakes here in Maine will be thawed for break in.

[@TheOutdoorConquest]

Still waiting on them to thaw here in Michigan too! Hopefully soon! Thank you for watching!👊🏻

[@MegaSling]

From the owners manual Engine Break‑in Procedure IMPORTANT: Failure to follow the engine break‑in procedures can result in poor performance throughout the life of the engine and can cause engine damage. Always follow break‑in procedures. 1. For the first two hours of operation, run the engine at varied throttle settings up to 4500 RPM or at three‑quarter throttle, and at full throttle for approximately one minute every ten minutes. 2. For the next eight hours of operation, avoid continuous operation at full throttle for more than five minutes at a time

[@TheOutdoorConquest]

Exactly

[@samkaleekkal2644]

I just purchased the same boat. Haven't received it yet. Thanks for the tutorial on breaking it in!!!

[@TheOutdoorConquest]

Hey thank you! Appreciate you watching!

[@TheOutdoorConquest]

I’m really loving the boat as a whole for sure!

[@drow8569]

Thanks for the video! I'm getting the same motor on my pontoon boat, hope to pick it up in September. Its a 2022, great info!

[@TheOutdoorConquest]

Not a problem! Thank you for watching! Feel free to subscribe to my channel! I’m going to be doing more reviews like this and a 1 year review on this motor!

[@cowboyup6438]

I just bought a 2020 Tracker 195 TXW with the same motor and the seller had taken it to Basspro/Cabelas for inspection and checkout and the paperwork shows 16.5 hours, but the comments say it's not broken in and needs to be run at higher rpm. So, maybe the seller just didn't have opportunity to run it WOT for very long wherever he was using it.

[@cowboyup6438]

So I just watched a video on FISH N STUFF'S channel and he took his back to the dealer because he couldn't get over 5k rpm and they told him exactly everything he did while breaking it in and they also adjusted his throttle cable and changed his prop. Keep that in mind on these new motors. The computer will tell the marine tech EVERYTHING you have done to your motor and if not properly done, they can void your warranty.

[@TheOutdoorConquest]

That is great information!! Thank you!

[@TheOutdoorConquest]

You’ll love the motor! Runs like a top!

[@g4outdoors]

I have this boat in the tournament edition. We broke ours in in one day. What a long day that was lol.

[@TheOutdoorConquest]

They are nice boats. So far I’m pretty satisfied all the way around. I’ve been River fishing for walleye for the most part

[@Diego-le5xt]

I'm getting my boat repowered with this motor and I'm trying to figure out what will my top speed be on my 23ft trophy bayliner. I was currently getting 22mph on my old '90's 175HP mercury outboard. I'm hoping I go a little faster than that and not decrease in speed.

[@SBrosOutdoors]

Ah yes, break in period. I know it is a lot smaller, but we got a little 2.5 horse mercury. Break in time seams like it takes forever haha. Congrats on the new motor.

[@TheOutdoorConquest]

Thanks brother! Yea it’s one of them things they recommended doing. I might be looking to get rid of her this spring though. We will see what happens. I’m really enjoying kayak fishing!

[@SBrosOutdoors]

@@TheOutdoorConquest Gotchya. Ya kayak fish is fun too. I only used mine twice last year though. We mostly just fish out of our Pelican 10' bassboat.

[@TheOutdoorConquest]

@@SBrosOutdoors I bought a new kayak this year but it didn’t show up until the lakers froze over 😫! I’m gonna do a few videos on it and how I’m going to rig it up for fishing. It’s a big boat. Pedal driven too

[@SBrosOutdoors]

@@TheOutdoorConquest ah man, that is a bummer. Look forward to seeing it come this open water season.

[@timwood8302]

Mine said that on the second hour run it at full throttle for one minute every 10 minutes

[@TheOutdoorConquest]

Hey Tim! Thanks for watching!

[@andrewbutlin8502]

Love the boat that's a sick setup. What did you name her?

[@TheOutdoorConquest]

Still working on the name! Thanks for watching!

[@andrewbutlin8502]

@@TheOutdoorConquest SS. Conquest

[@aviationlocation7993]

My Mercury manual says for the first 2 hours, run varying speeds up to 4,500 and 1 minute bursts at WOT every 10 minutes. Say nothing about 1 hour 3500 and 2nd hour 4500. What is correct?!

[@TheOutdoorConquest]

WOT once every 10 minutes only after the first hour is done. Not over 3500 in the first hour. But yes, varying speeds throughout the entire first 2 hours. This was the information in my manual for the 2021 150HP.

[@jackwelsch8695]

My manual also makes no reference to the 3500 rpm limitation. Perhaps they have changed the manual. I took delivery of my 2021 150 Pro XS in April 2021.

[@TheOutdoorConquest]

@@jackwelsch8695 these were step be step instructions given to me from my Mercury dealer. Thanks for watching!

[@jamesglavich1426]

"Aviation Location" My manual says the same, although it is a 2023 it should be the same. He said the dealer made the references about the 3500 and the 1 hour deal. I guess the dealer didn't print the manual.

[@731catfishing8]

I'm looking at that same boat the only question I have is what is the fuel range with the 150?

[@TheOutdoorConquest]

I haven’t done the math on figuring out MPG but it definitely isn’t a gas hog! Thanks for watching!

[@731catfishing8]

@@TheOutdoorConquest just off the wall would say around 200 miles a tank? I'm not to concerned on mpg per say just range my thing is if I should run the 150 or the 175hp had someone say the 175 was getting about 180 to 200 miles per tank but if I don't have to upgrade that would be great lol

[@TheOutdoorConquest]

@@731catfishing8 I would agree that 200 miles per tank would be a fair estimate.

[@CamilleTylerbrand]

Hello from Texas

[@TheOutdoorConquest]

Hello! Kind of wish I was in warm climate of Texas right now! Thanks for your support!

[@laurengeorge2766]

What prop are you running?

[@TheOutdoorConquest]

Mercury Enertia 3 blade prop!

[@terryogletree2128]

What do non ethanol fuel , total 10 hr break in is probably several tanks of fuel

[@TheOutdoorConquest]

im unsure about that

[@GeorgeBonez]

Greg how fast does that 150 push that boat? I have the same motor on my new 24ft Tritoon and I can get up to 35-37mph. I was just wondering how fast it could go on a lighter boat like yours? Thanks bro and thanks for the vid.

[@TheOutdoorConquest]

Thanks for watching, with 2 grown men loaded with gear and a full tank of fuel I can hold 38 mph wide open throttle

[@GeorgeBonez]

@@TheOutdoorConquest Wow that’s pretty good but I think I may have originally underestimated how much your boat weighs. Just saying its prob not as light as I thought.

[@TheOutdoorConquest]

@@GeorgeBonez no its definitely not light. It’s heavy duty for a 19 foot aluminum deep V boat.

[@chadjohnson2269]

I’m lucky to get 30 out of mine on a Tritoon...what prop do you have.

[@TheOutdoorConquest]

@@chadjohnson2269 thanks for watching! Mercury Enertia 3 blade

[@liamcarroll5615]

Hook, Line and Sinker bro

[@TheOutdoorConquest]

Thanks for watching buddy!

[@yahatinda]

EVINRUDE,NO BREAK IN

[@TheOutdoorConquest]

That’s awesome!

[@truck57us]

Evinrude: Currently out of the outboard manufacturing business...

[@jamesglavich1426]

Evinrude, no break-in??? Evinrude where are you???