How To Build DIY Auto Reverse Polarity Motorized Video Slider - Update

[@jims9895]

DUDE, SERIOUSLY I HAVE BEEN LOOKING ALL OVER KZbin FOR THIS AND HAVE ASKED MANY A MANY OF THE ELECTRIC CIRCUIT GUYS...ALOT OF THEM HAVE SAID THEY DONT KNOW OF A WAY AND SOME SAID THEY ARE TOO BUSY TO HELP.... THANK YOU SOOOOOO MUCH FOR THIS.. IT IS VERY APPRECIATED

[@tompurdon3817]

Thank you! I used your auto reverse circuit to make a DIY light rail mover for my grow lights. Works great!!!

[@hugobaptista9374]

Thank you for this! I have the same setup but want to connect the speed controller. You mention you will talk about this later. Have you already? How do the connections differ?

[@flashmico]

Hey, thanks so much for this video. I am in the process of putting together a similar build and I am hoping you could point me in the right direction as to how I can incorporate the speed controller.

[@1018whitewolf]

great diy. is there a link to the other DIY schematics of the wiring or a picture showing the actual wiring. Thanks

[@orange42]

The C stands for Common or Centre. NC is Normally Closed, as you said. It's the differing contacts on the switch.

[@Steve_Bonham]

Great information and DIY;looking to make this for the studio however I have a few questions. What are the parts you’ll need aside from the electronics?

[@lonman4740]

Nice job, very professional. Do you have anything on the rotation of a 12v cctv camera and 12v motor with reversible movement?

[@Totltech]

can this be found commercially ? would love to buy one

[@MrCheesyCam]

This video is about a DIY project with the circuit. More info on the slider has yet to be released.

[@nerastud3716]

Mine stops at one end, you said change the switches? i don't understand both switch are the same or you meant the socket numbers ? Could you explain what i am missing please... Thank you Big tum and subscribed...

[@charles910]

What motor speed do you recommend? I just want it to slide back and forth so I can be in the video with my kids and birthday parties.

[@MrCheesyCam]

I would say under 20rpm. In my video I was using a 20rpm motor but I think it was a bit fast.

[@enigma1331e]

Have you figures this to work WITH the CONTROLLER? Inputting to Controller then to battery? Or will the defeat the system? Thanks

[@schweinhund227]

Most excellent ! Thanks for sharing ! I would love to have a set up like that..... maybe one day ?

[@MrRidelis]

Thank you very much for that tutorial excellent And easy to build. I have a quick question, can you tell me how to connect a pir sensor to the circuit. Thank you so much for your help. Great job!! Ricky V.

[@Jonhillenbrandphotography]

Very interesting. It would be good to have some sort of marine case to put it all in so that it was waterproof as I use my slider outside mostly. And the speed control is somewhat critical for time lapse. Thanks for posting this though. I'll have to take a closer look and see if I can make this work for my needs.

[@jackdarashakespeare8056]

How could you set up a Push To Make switch over a SPST or on/off switch ?

[@enigma1331e]

I hate to ask an some what obvious question..but... How many Wire Connections? 12? and sizes. Thanks. Hey I'm a newbie with electronic. The Battery and Motor is the only ones i know for sure. Thanks again. LOL

[@perico9385]

i can do an anti pinch system for this??? i want to do someting biger.. and i want to know if is posible ?

[@orange42]

Great stuff!

[@phuketvirtualestate8981]

Are you selling these stuff as a kit?

[@enigma1331e]

How could you set up the limit switches to just STOP the carriage? thanks

[@MrCheesyCam]

+Frankie e You just wire it in a way that breaks the circuit.

[@tatafatahillah]

Pwm di pasang nya ke kabel apa??

[@tatafatahillah]

Please switch 1 motor very slow switch 2 motor high speed why??skema same to picture...

[@nerastud3716]

i have the same you have in the diagram, same what you say here in the video, but just stops at one end and gets stocked please any suggestion... this is my limits switches www.amazon.com/gp/product/B076GM7JQP/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1 but i don't think could be the problem because has the same functions C - NO - NC please help me understanding you said changing sitches or how do i know which B and A?