How to build simple Router Sled and a Table | Woodworking

[@jmac4988]

Like the "Can Do" feel of the video. you showed how to build and the final results, of the sled . I appreciate you sharing your work . Some one said its not safe ..I disagree .. two feet on the ground , two hands on the router , eye protection, seemed aware and alert.. Safety is always an issue, with power tools, it's inherent .

[@Kultakala_Design_Studio]

Thank you for the constructive comment 🙏

[@jplieurance]

I like your adjustable stop. The only suggestion I would have would be to add some spacer blocks on both ends so that the router bit could travel the whole width of the sled, and allow you to eliminate the sideways travel of the guide - that, I believe, is what a previous commenter was referring to when he was talking about a safety issue. Nice job

[@kevindumas1743]

So glad to watch your video, it’s actually going to inspire me to make one, I’ve been putting it off for a while, I have a lot of tree cookies that are ready to be made into tables. Hopefully it goes as well as yours…😀

[@Kultakala_Design_Studio]

Thank you and good luck 👍

[@kchassa_]

Amazing work dude!

[@Kultakala_Design_Studio]

Thank you 🙏

[@XDIY]

Great Jig, well done!

[@Kultakala_Design_Studio]

Thanks Itzik !

[@RoninJeremy]

was thinking about steel or ALuminum, both have pro's and cons, looking at your video, is the sled bending? or is it the camera angle / lens?

[@Kultakala_Design_Studio]

@@RoninJeremy no its not bending

[@RoninJeremy]

@@Kultakala_Design_Studio thanks for clarifying, aluminum it is then. Cheers!

[@Kultakala_Design_Studio]

@@RoninJeremy im using steel, aluminum will bend.

[@RoninJeremy]

@@Kultakala_Design_Studio thanks for clarifying, it really looked like you were using Aluminum, from the color and the inside corners not being very round.

[@eyalklein1453]

אלוף , כל פעם הפתעה חדשה !!!

[@Kultakala_Design_Studio]

תודה רבה !! :-) יש עוד הפתעות בדרך ... :-)

[@Shay_776]

Good job :- )

[@Kultakala_Design_Studio]

Thanks !

[@notcharles]

What / which bit did you use?

[@Kultakala_Design_Studio]

In this video im use straight cutter 2 flute

[@kevindumas1743]

What horsepower router do I need? is a 2 hp router enough or should I get one stronger? I saw a 3 1/4 hp router on Amazon, really need to know…Thank-you… also, which router bit will I be using to smooth table tops?

[@waynereckzin7143]

I had pretty much the same question.

[@netanellalazar3819]

מסביר מעולה ואני אוהב גם את המוזיקה ששמת לנו ברקע! זה נראה שזה לוקח לך הרבה זמן, לא שווה כבר לקנות מקצוע חשמלי?

[@Kultakala_Design_Studio]

תודה רבה, עם הרעש שהכלי הזה עושה חייבים מוזיקה רגועה :-)

[@santabaia]

Very nice.👍😊. One question: what's is the length of the iron jig? Thanks

[@Kultakala_Design_Studio]

Thank you, the length is 1.50 meter

[@IamTiagoBorsa]

Nice job! I'm making a similar video to put on KZbin. ✌

[@jungbechtospk40]

I have done very similar with woodglut designs.

[@paulhaynes6052]

Stopped watching 1/2 through, how not to do it.

[@MrDakman]

That sled looks so dangerous... There is a MUCH better way to build that sled, and safely I might add...

[@Kultakala_Design_Studio]

Why do you think it is dangerous?