How to Calculate Size of Cable Tray and How to Install Cables Inside Cable Tray (Part 1)

ElectriCalc Pro from Calculated Industries available from this link:
amzn.to/3wJrmz3
Sa video na ito ay tatalakayin natin ang tamang paraan ng calculation ng size ng cable tray at ang tamang paraan ng installation ng cables sa loob ng cable tray na ayon sa Philippine Electrical Code. Ito ay ang unang bahagi na tumutukoy sa multiconductors. Ang ikalawang bahagi na dapat ninyong abangan ay tungkol sa single conductors.
Credits:
Intro Sounds: Bensounds.com
Intro Clip: Pixabay.com

[@VenjieVlogSubscribe]

Salamat sa karagdagang kaalaman na ibinahagi mo samin.more power and God bless..

[@jcpthedreamer]

wow usapang matatalino salaman sa kaalaman idol

[@its_me5597]

Ayos talaga lods ang mga content mo. More upload pa lods.

[@ShieFelices888]

Thank you for sharing sobrang informative po nito.

[@PekengIlokano]

very informative. Thank you for sharing

[@japs244]

Life saver para sa mga nag uumpisa palang sa design salamat sir!

[@RandyAmorchannel]

Salamat sir. Enjoy the videos and God bless!!!

[@vrbaac1641]

Very informative video po... question po.. same po ba yung sinasabi na "Solid Bottom Cable Tray" at Trunking in sizing po? salamat ng marami po ^^

[@RandyAmorchannel]

Solid bottom cable tray ay basically pareho sa tinatawag naten na trunking in terms of construction. Sa tawag lang nagkakaiba. Salamat sa panonood ng video ko sir.

[@cas49713]

Sir ano PEC edition yung ginamit sa presentation

[@RandyAmorchannel]

Di ko sure pero parang 2011 pa yata gamit ko jan boss

[@cesargascon5639]

How about the earthing conductors, how it will be installed?

[@RandyAmorchannel]

Good day sir. May 3 methods for Equipment Grounding Conductor related to cable trays. 1. EGC can be included in each mutli-conductor cables. 2. Use the cable tray as EGC if permitted according to NEMA VE-2 3. Use separate EGC installed inside he cable tray and bond each section cable tray section to the EGC and both ends of the cable tray system are bonded to nearest grounding busbar. Sana nasagot ko yung question mo sir.

[@jimmyaustria4019]

san po galing yung Plus 50mm sa Sd? Thanks

[@randyamor3299]

Sir yung 50mm sa Sd is given yun sa example na may 50mm spacing between larger cables and smaller cables. Pwede walang spacing basta pareho ng voltage grade.

[@rhendelfabriga6583]

Hindi po ba yan mag kaka line to line fault

[@RandyAmorchannel]

sir hindi po yan magkaka line-to-line fault basta walang contact ang conductors in this case ok naman insulation saka may IR test naman yan bago i terminate. I hope I answered your question. Thanks

[@jamesianbracero1005]

Boss pde po pa calculate ng size of cable tray? Sample po is 3-50mm2 XLPE Cable at 1-38mm2 BCW . Salamat ( 150mm x 30 mm po ung guess answer ko.)

[@RandyAmorchannel]

Good day sir. Ang cables mo ba ay tatlong 3Cx50mm2 at isang 3Cx38mm2? Kung ganyan ang size at quantity ng cables mo ay pasok na sa 150mm wide na cable tray pero alanganin yung 30mm cable tray height gawin mong 75mm.

[@jamesianbracero1005]

@@RandyAmorchannel bat po 75 mm? Isang layer lng nmn po. Tapos 3 sets lng po ng 1C 50mm2 XLPE. Tama poba sa 150 mm x 30mm? Correct me if im wrong. Salamat

[@RandyAmorchannel]

@@jamesianbracero1005 tama sir yung 150mm width pasok na dun yung 3 - 1Cx50mm2 pero yung diameter ng 1Cx50 is alanganin sa 30mm high na cable tray and besides yung table ng cable tray sizes sa PEC ay base sa 75mm. Check mo sir yung OD ng cable.

[@jamesianbracero1005]

@@RandyAmorchannel ok po boss. hehehe salamat. 150mmx75mm po gamitin ko. apple to apple ko kasi pag compute ko sa depth ng tray

[@RandyAmorchannel]

@@jamesianbracero1005 No problem sir you're welcome

[@qqqqqqq198]

pls share the pdf