How to change a car battery without loosing memory in MODERN CARS!!!

This video will show you how to replace and change a car battery in modern cars! how long does it take to replace a car battery? In this video we will show you how to quickly, easily and safely replace your car battery.
Here are a few reminders when replacing or changing a car battery especially for modern cars
Negative cable first for removal
Positive first for installation
Always keep horizontal
Make sure to use a Memory saver
QUICK LINK TO BUY THE Memory Saver FROM AMAZON WITH QUICK SHIPPING: amzn.to/33PCpuB
***********
FOLLOW US ON INSTAGRAM! - / thejabbour
***********

[@bluelemonade6200]

Hands down. One of the best videos out there that shows clear steps and showing safety steps properly

[@asianstud7]

Wish i found this video soon. Too late . My engine was violently shaking after swapping out my battery. Lost all presets and memory of how my car was supposed to run. Well now I know.

[@tommyd6665]

I don’t have a small power source , can I connect the positive and negative cables to another cars battery ??

[@markramsey8717]

When using a memory saver the positive cable stays hot, put a rubber glove over it so it doesn't ground out.

[@vegajf51]

Exactly, any quality memory saver will include that in the instructions.

[@onenikkione]

Thank you for pointing this out - very Important!!!

[@takeiteasymac3206]

Thanks

[@stifflers69mom1]

You saved my ass …I’m just coming back to this comment to thank you …..I put a rubber glove over my positive and I’ll be damned I pulled that battery out and didn’t that damn wire flip right out and smack the inner fender of my truck….if the glove wasn’t there I’m positive I would have pop some fuse or even worse…..THANK YOU SIR

[@brentneahring2797]

​@@stifflers69mom1I covered both with ziploc bags

[@ayoCanada0921]

I'm about to change my battery, it's very important that I have to watch this carefully

[@leoseries]

I used the same method but I only needed a 9v dry battery to maintain the memory whilst I swopped the car battery. I made sure that all lights including the courtesy (door open) light was off and that the infotainment system was off. It worked fine.

[@richardstoehr9326]

It was a good video on how to save your presets my question would be why would someone put a new battery in and not clean the cables?

[@onenikkione]

and after cleaning them use die-electric grease

[@SuperFredAZ]

Should you have wiped a little grease on the battery terminals after installing?

[@gabbytanner7059]

Thank you so much, you made it clear and easy to understand

[@flymoracer]

there's an additional step that might be necessary. The battery monitoring system will need to be reset, coding the new battery to the car, allowing the charging strategy to be adjusted for the new battery. You'll need a suitable diagnostics scan tool for this, or might need to pop into a garage or dealer that has this equipment. The car will likely run just fine on the new battery, but an incorrect charging strategy could reduce the lifetime of the battery.

[@dhowar]

I have a 2007 Toyota Sienna and have changed the battery without a memory saver and haven't lost memory. What year cars did the memory loss start?

[@CoffinNeAler]

I have a 2008 Kia Optima 2.4L and any time the battery is disconnected even for a second the computer loses its fuel settings and the car takes forever to relearn how to properly make the engine run without dying. I believe I have a bad ground and want to disconnect the battery and work on that. So I'm about to use a battery saver to keep my fuel settings. Just wanted to see someone else do it before I did it wrong and fried my car. This video is great and luckily I read some other comments that noted you should cover the positive battery cable when you remove it so it doesn't ground out while using a battery saver. My kia doesn't have that nice positive battery cable cover like the one in this video.

[@mr.blizzie1200]

It varies widely depending on year/make/model. Some makes and models have been doing it forever, some just started a few years ago.

[@charlesdowns1691]

2002 3.1 pontiac grand prix will lose settings if battery disconected. i need one.

[@johnrodriguez1145]

I can't remember

[@THEFIRE360]

I've replaced batteries in a 05 lexus, 15 sienna, and a 16 Altima. Never used the memory saver and they still had all their memory.

[@Ultecpo]

You're one of the lucky ones

[@onenikkione]

It all depends on the car you are working on - they're not all the same

[@Okinanam69]

Just use an extra fully-charged battery on the side to power using a jumper cable.

[@checkyoursix5623]

Most folks don't have another car battery layin' around. Many do however in the form of their riding lawn tractor battery. Just run it up alongside like you were going to do a jump start.

[@garydeandeery]

I’m trying to reset my PCM If I leave my battery off for few days Then fit again will the PCM reset then I’ll do the running ecu relearn it’s an rx8 with p0610 code

[@waynebeck7801]

So if you plugged the booster pack into an always on cigarette lighter port would it work the same way?

[@jaygre4836]

Showing a 12 V accessory to plug in your computer saver, is OK if you have one. It would have been better if you would have also shown how to connect if you don't have the peripheral equipment.

[@niacal4nia]

Does the jump starter's amp matter? Because I was told the obd2 port's fuse is around 5-6 amps. BTW some newer cars need a scanner to program the new battery.

[@n40798]

Is the cable long enough to reach a nearby car?

[@westonlee9778]

Could a external power supply be connected to the battery terminals during the battery replacement as an alternative to a OBDII memory saver? I'm thinking if I keep power on the terminals then the objective would be the same. thank you

[@Grumpy412]

I was think the same. Did you get a positive reply to this from somewhere? I was thinking of connecting a battey tender to the terminal cables.

[@ASUSfreak]

In theory it should be able. If your charger can output enough amps. Also some chargers don't output anything if they can't "feel" a connected battery. Just be sure NOT touching the chassis or short circuit will happen. Also it is a hassle to keep the cables connected to eachother and moving them around and not shorting so...

[@MrTrev2507]

Just hook up a battery jump pack to battery leadstake battery off, replace battery connect leads, unplug jump pack, job done

[@asterixky]

It doesn't save all the settings, it just keeps power to the car.

[@sorinsorin20]

What happens if you lose your settings? How can you restore them? The guys at the shop changed my battery and didn't do any of these. Now i have none of my settings even if they are checked in my car settings menu

[@charlesdowns1691]

just have to drive it and they will restore themselves after awhile. drive it in all situations. low speed+highway+ but they will always reset. gm products are absolute worse for a quick reset. other cars will vary but gm takes forever!!! dont use cruise control when driving+it will take longer.

[@XKnightLightX]

Newer cars will likely require an expensive $500+ bi-directional scan tool to reprogram different parts of the system

[@cnakamashi]

Very nice explanation. Thank You!

[@ryan9701]

Thanks!

[@goddessmanbo5374]

102.3 you must be in Florida thank you for this video

[@jusssy5078]

Hi, Ryan, what State do you live in? Looks nice!

[@arthurranara510]

I understand what you are trying to point out when replacing old battery with a new one the sitting and the memory won't changed/ will be reset why not just start the engine before you removed the old battery and changed thank you

[@lamarw7757]

On older cars, that would work. On newer cars, it will damage the charging system.

[@jsh12jho51]

Can be done with a car charger or using a pair of jump leads. This is a better and cool idea and it works. TBH HOW many people is going to be changing the f.. ing battery more than twice in its lifetime Let alone buy this memory saver shit

[@nunika1975]

I though you can just use a 9v battery memory

[@anyarussell1166]

If you dont use the memory saver. Will it forget your car fob signal to start car?

[@flymoracer]

No, it wont

[@mikedimaria5460]

If you are working on car for extended time...is it safe to keep battery saver connected??

[@eutimiochavez415]

What happens if u loose ur memory on the car ?

[@mistervacation23]

I'm positive about the negative, but a little negative about the positive.

[@frankcruzrosado133]

Does this method applies to a 2018 tiguan when changing the battery?

[@marcostudd]

Why install the mounting bracket before black cable? Just curious.

[@CoffinNeAler]

Just a safety to keep from grounding. Once the circuit is complete anything that touches the frame and a hot wire can short.

[@terry_willis]

So the memory saver device is $17.00 and then I have to buy a battery for $150.00 to power the memory savor. And then keep adding water and charging the $150.00 battery until next year when I need it again. Sounds good to me.

[@michaelerwin8744]

Is it true when polarity is reversed, car's computer hardware will be fried?

[@nickv4073]

All cars have fuses. If you are lucky, fuses will blow and protect the electronics. However, there is no guarrantee you will be that lucky. My advice is DONT PUT THE CABLES ON BACKWARDS.

[@CoffinNeAler]

DO NOT PUT THE CABLES ON BACKWARDS!!!! In a rush to try and sell a vehicle that had a dead battery I fried it by putting the cables on backwards... only cost me about $250 bucks because I sold it for scrap instead. Just a well lesson learned!!!! It could've just as easily fried a much more expensive vehicle.

[@charlesdowns1691]

dont put reverse

[@alann5003]

Is this necessary for cars made before 2000?

[@5.43v]

Not necessary for any year car

[@rogelio2931]

Aftermarket head units, will all settings be saved too?

[@KenTronico]

When I'm using the memory saver, do I connect the clips together with the device on or just connect it

[@robertmaybeth3434]

Plug in to your OBD II port under the dash first. (If your battery was giving it enough voltage before you disconnect the battery, this will prevent interruption of power to the computer, if your batt is already dead, it's too late anyway, so no need to use the memory saver). Now connect it to your power source. Another car works, or even another (good) battery, but probably NOT your new battery... I think, I thought at first to use the new battery but I don't think you can, since you have to disconnect the clamps from the memory saver to install the new one, on most batteries. If the disconnect of the clamps is momentary, it still might hold your computer settings, maybe - but i wouldn't try it unless there is no other way.

[@hotsauce7362]

Why can't you just use the jump starter cable and connect them to the car battery terminal, like a wire or something and then remove the battery while the car is still actually connected to a power source. Then when you reconnect the car battery terminal with the car battery, you can remove the wire and disconnect the jumping cable.

[@westonlee9778]

that was my question couple minutes ago...did you get an answer?

[@jsh12jho51]

Can be done. This is cool idea and it works. TBH HOW many people is going to be changing the f.. ing battery more than twice in its lifetime Let alone buy this memory saver shit

[@Tony-dx3eo]

I was thinking the exact same thing...my battery-powered jump starter puts out 12 Volts and has alligator clips...will be a breeze to use that method instead.

[@CoffinNeAler]

Just make sure your positive doesn't ground out!!!

[@emilbala9366]

great idea!

[@AdelAbuAlaa]

what about if i don't have battery saver ?

[@onenikkione]

buy one

[@tee228]

why can't you use the main car battery as the 12v source?

[@michaelsliwinski8044]

Very clever!

[@CoffinNeAler]

Hahaha, ummm because you're changing it?

[@tee228]

@@CoffinNeAler no. ppl need to do other stuff with the battery disconnected without losing memory, not only changing batteries.

[@AdelAbuAlaa]

that's what i always do and no dramas at all

[@AdelAbuAlaa]

@@CoffinNeAler you missed the point

[@dgriffin6074]

I used a Memory Saver that uses a 9 volt battery and plugs into a 12 volt power plug; oddly, the radio station pre-sets were saved but not the radio/sound system calendar and time settings. The seat settings remained the same but then I have manual seats....hahaha. Any idea why some but not all the sound system settings were preserved?

[@dgriffin6074]

@@torTxoFognaTuluZ I used it once,. Only problem was having to redo my radio presets. Other then that it ran fine. What can you expect for $11?

[@vegajf51]

@@dgriffin6074 This type works best www.amazon.com/dp/B07KCN69LJ?ref=myi_title_dp

[@TheThirdWheel618]

I guess I got lucky I changed my battery on a 2013 Sonic but after learning about this I don't think I would do it again without that memory saver . I wasn't worried about settings since I didn't know I could lose settings but I heard it's bad for the computer to remove battery then put one in again .. but then why do they use that method to re set the computer to clear engine codes ....

[@pandyahk2004]

I have Ford ranger 2017, I tried replacing battery, engine or anything won't start at all. Is it due to it's need resetting?

[@Dakdizzy]

it may be the key or key fob.

[@markfox1545]

Can you have engine running as you exchange batteries?

[@onenikkione]

NO

[@odubb45]

You can, but you shouldn't. You'll get a big spark when you connect the battery, because of the voltage difference. Also, if you short the positive terminal, you could ruin your alternator, maybe even your car computer, who knows. Not a good idea!

[@ww89]

Is there any big deal if I don't use the memory saver?

[@atticstattic]

It _can_ be a big deal if you need a security code to reset the infotainment system and don't have it...

[@garydeandeery]

atticstattic when you start the car again you need to leaving running for 15mins to learn tick over then go for a drive and drive slow no heavy foot driving so the ecu learn again

[@qtipie00]

Thank you!!! LIKE LIKE LIKE :-)

[@makumel]

Is the car ON OR OFF

[@mescnick]

The car should be off.

[@usnewbies]

Mercedes information system

[@AdelAbuAlaa]

as if everyone has battery saver at home

[@dannevang44]

Let the car idle vile you change the battery, get someone to hold the positive led

[@onenikkione]

NEVER

[@Maugwa]

A jump box connected to your cables does the exact damn thing. Any auto parts store will do this for you or just borrow a jump box.

[@Tony-dx3eo]

I was thinking the exact same thing...my battery-powered jump starter puts out 12 Volts and has alligator clips...will be a breeze to use that method instead.

[@tonystormcloud6889]

Never lay a metal tool on the battery.

[@cq7415]

Some comments better, don’t have to buy anything.

[@charlesdowns1691]

cause it took me around 700 miles to reset everything)

[@mariahanastasi6575]

Why WHY?! Are nearly all the videos about changing car batteries all about new cars!!!! I just want a video that shows me how to change the battery in my 1980 ford bronco! I know when doing this it won’t screw up the fanciest thing in the car, the ashtray! UGH!!!!! Everyone is always promoting a tool, a spray…! If most of us can’t afford gas right now how would we afford all the tools? The battery was expensive enough!

[@urbanpeltier1622]

Officer Friendly

[@yumpinyiminy963]

What is all that crap on the positive battery cable? Ka, Ka, Ka KIA pet!

[@robertmaybeth3434]

If you watch this on 1.5 speed you still get the info but... FASTER

[@sekacity3425]

I can't trust this, you think losing is spelled loosing .

[@class1188]

DONT JUDGE & YOU WILL NOT BEJUDGED! No one cares about a misspelled word. NO ONE.

[@kylegauths4718]

Lol, i guess because this is a KIA, you don't actually need to do that with a Honda or Toyota, and who needs to change a battery after only after a few years. get a good battery that will last you 8 to 10 years. never had to change a battery in my cars that were less than 7 or 8 years old.

[@Tony-dx3eo]

Batteries just don't seem to be made as well as they used to. Any suggestions on a good brand of battery I could pick up at my local Wal-Mart?

[@kylegauths4718]

I know batteries are not as good as they used to be, but I live in Ontario Canada ! I really like the interstate batteries!

[@Tony-dx3eo]

@@kylegauths4718 Thanks for the feedback Kyle--I'll be sure to include interstate when checking out my next battery purchase.

[@ZeusBike333]

Not true with the Honda Fit. Search all the KZbin videos on swapping out the stock 151r dinky battery that Honda saw "fit" to install with a larger 51r. I love my Honda Fit but just can't understand why Honda continues to install the 151r all these years when it is clearly not up to the task in cold weather environments of North America.

[@bmfilmnut]

I think you mean "losing." It seems spelling is a lost art these days. Foreigners must think Americans are all illiterate.

[@ojstinson]

The correct word is "Losing" not Loosing, loosing is to loosen something like a bolt or screw.

[@therapyindex]

There is no such word as loosing.

[@flbyrne99]

Losing is to lose something. Loose means not tight. No such word as loosing. This guy is showing how not to lose something. He is not losing the car settings..

[@onenikkione]

this is not an english spelling video

[@Okinanam69]

@@flbyrne99 You mean," not a virgin" anymore?" LOL!

[@johngreene6783]

Should we believe a guy who can't spell "losing"?

[@ryan9701]

Is it spelled like this? You are a looser? 😂🤣😂

[@buddyrevell511]

Dude, it's spelled "losing", not "loosing"... for crying out loud spelling isn't that hard.

[@ryan9701]

I don’t really care about your opinion.

[@sanitary103]

ya know it's okay to correct someone but no need to be a smart ass about it.