How To change clutch on Yamaha YBR 125 ED6 engine

How To change clutch on a Yamaha YBR 125 ED6 engine, without removing it from the frame.
I used EDC CK1151 clutch plates.
You will need:
8mm, 10mm, 19mm socket
8mm wrench
Tyre lever
Hammer
Clutch plates(which sat in engine oil at least 24hrs)
Engine sealant
Engine degreaser
1 liter of fresh 10w-40 oil

[@bottletree33]

It’s so nice to do jobs like this when your oil pan bolt has not been rounded off and the little bolt near the footrest has not been rounded off too

[@simondoesthings]

True, my bike is in very good condition, so I don't have problems like that. I recommend a lot of patience 😂

[@jorgelenin6078]

La balinera de arranque está en esa área también? Me está dando aguas esa pieza

[@osmanekinci4681]

Mükemmel video olmuş thank you bro :)

[@szymongizicki4537]

Hello great video I just have one question I had to replace the seal on my clutch rod as it was leaking but now my clutch rod won’t slide fully back down into the engine and it feels like it’s hitting something do u know how to solve this problem it’s very hard to find info on these bikes

[@simondoesthings]

Do the splines interline? As far as I know there's only one way to put it back and it won't fit if you turned the rod. If you can, make a short video of the problem and post in on your channel, then comment here again, I'll see what the problem is and will help you to the best of my ability. I have a full service book for those engines so I'll have to be able to find something.

[@diegomuuo929]

Hello simon i wish to ask you when the clutch assembly is removed is it normal when you kickstart the yamaha the lever is loose or in other words free and no engine compression?

[@simondoesthings]

@@diegomuuo929 yes, the clutch connects the lever to the crank

[@nadjib3ajib268]

After how many km you should change it ? i am almot 40 000 km on my ybr ed year 2021

[@simondoesthings]

@@nadjib3ajib268 whenever you feel like the grab from the clutch is not good enough

[@rabone1968]

thanks for doing this good video helps a lot

[@HiHi-vs2tk]

hi do you have the service manual

[@ZainRaza-gh3wl]

I have the service manual. Do you need it?

[@Qualcomm_petro]

do they have these friction and steel plates for this bike on Ali Express?

[@simondoesthings]

They do - but there so inexpensive you are probably going to spend less buying local when you don't have to pay for shipping

[@glukerpk3010]

I changed the clutch with all the discs even the metal ones, I changed the springs but the clutch slips the same every time I accelerate hard. When I start up a hill the clutch shakes. I'm desperate I don't know what to do anymore

[@simondoesthings]

Is your clutch basket ok? Does it have signs of wear where the metal plates mesh with the basket? Did you adjust the central bolt correctly? You need to do that when you change the clutch, otherwise you'll burn it straight away.

[@glukerpk3010]

@@simondoesthings clutch brasket was perfect bike has only 25k km , how to adjust central bolt? i adjusted that it disengages the clutch when i press the leve, is that ok?

[@simondoesthings]

The manual states that you need to fully undo the adjustment screw near the lever on the handlebars, then screw in the middle bolt untill you feel it touch the engine's clutch lever

[@simondoesthings]

25kkm might wear out the basket if you were hard on the bike

[@GooseDub]

@@simondoesthings did he put his plates in oil for 12-24hr

[@strannikstrannik1]

The engine protection bracket needs to be sawed off, not bent, IMHO. It is not needed. If you lay the motorcycle on its left side (soft place), there is no need to drain the oil.

[@simondoesthings]

@@strannikstrannik1 you do you my friend!

[@EdwardVermanis]

Can’t wait to this and my bike don’t start

[@simondoesthings]

@@EdwardVermanis im sorry, i don't understand. You want to do this and you also have a no-start? If you give me more details I can help

[@КопыловВячеслав-з2л]

где такие дуги взять можно?

[@simondoesthings]

I don't know if I understand you correctly but the clutch kit is from eBay. Generic ED6 Yamaha engine clutch - remember to keep it in oil for 24hrs before install.

[@КопыловВячеслав-з2л]

@@simondoesthings No. Where can you buy protective arches? How about you

[@simondoesthings]

@@КопыловВячеслав-з2л they're available in Poland "from the shelf". Your should try allegro.pl, they ship international

[@V6PSC]

​@Simon does things why do you have to keep it in oil for 24 hours ?

[@simondoesthings]

@@V6PSC this is a wet type clutch system, the disc is always submerged in oil and the material with which the clutch is made is organic in origin. By keeping it in oil for 24h prior to instal we're giving it the best possible conditions for lasting as a long time. Hope I answered everything 😁

[@senorx942]

2:58 really??

[@simondoesthings]

I know what you mean, but you really need those few cm's to remove the engine cover 😂

[@senorx942]

@@simondoesthings 😂 Dont be lazy, remove de footrest

[@simondoesthings]

Noooo, that's like 10 minutes of work more 😂😂😂

[@owenbarrow6825]

Is this the same as a 2013 clutch

[@simondoesthings]

Yes, should be the same 2010-2018