HOW TO CHANGE FIT NEW AVID JUICY HYDRAULIC BRAKE PADS

This video shows how to change pads on a set of avid juicy hydraulic brakes.

[@SuperOlds88]

Very good quality video, very clear, no fumbling around like me, no cussing, throwing tools. Thank you for this video, seriously.

[@bobcallender8088]

Excellent video, thanks that clip was kicking my a@#, I was trying to put it in after the pads , thanks so much.

[@guarderiakirikoulucia2005]

I had been trying for a long time to know how to change the pad in this type of brakes, and I finally succeeded thanks to you. I thank you very much. Greetings from Spain.

[@dongkapuyawn5107]

Cool video! I was skeptical of removing the assembly from the fork on my bike because I might screw up the alignment. I removed the wheel instead for open access during uninstall and cleaning of the brake area.

[@P_double_H]

I just bought a used bike to ride around the neighborhood and I found out it came with Juicy 7 brakes.. i didn't even know these brakes were hydraulics... This thing brakes really good.

[@BodyFixExercises]

Great, but make sure you don't touch the pads with greasy gloves so you don't get contaminant on the pads! (Else they will squeak or not work as well)

[@corvus3200]

Best Video, easy to understand....

[@josedecanyas]

Se ve todo muy claro. Buen trabajo!

[@carloiannotti8504]

great and clear !

[@JonanthonyTarlen]

I installed them without draining the brake or even taking it off😂 I was dying but it’s done

[@K0ALA.]

Thanks for the vid! Helped me know what way round the Metal Spring is meant to sit. Cheers

[@hamzachetouane969]

greate video, thank u

[@joshuablacklee13]

I'm trying to do this right now but really really struggling to get the pads back in place, I cannot get them to slide back into the caliper. any tips advice?

[@TheErsatzMode]

+Joshua Blacklee. The uploader replied to your comment but you probably missed it.

[@garyduran1]

Thank you

[@metalmorgan]

Thanks!

[@Mr3kites]

Seems a good method, going to try it, cheers thank you.

[@eminence_]

I did this, but now they just constantly breaking. Wonder if there is a way to loosen them. They are just way too tight.

[@elmakednos]

You have a piston stack case.Go to your mechanic or reset pistons mant times using brake cleaner.

[@recordandplayorg]

did you push the pistons back in to the caliper, be sure they are the right way round. push hard, they should click in to place.

[@WingsOfADream1]

at the shop we had a tool for this for cars, I'm using a pair of needle nose in reverse but I think I may have a seized piston... the brakes felt like shit and the pads are worn pretty good, not to metal but pretty close, the old pads came out in 3 pieces and I can't get the new ones back in as 1 piece... I kno I could release reservoir pressure and test if it is seized but I fear I would have to bleed it then... My 20/20... when u used the flathead at 1:27 I did the same but I would pry WAYYY harder to fully compress piston... fudge fudge fudge. edit: can't say I recommend it but if you put in 1 pad and tension clip then pry back the clip from the top with a small flathead then ease in 1 side of the remaining pad into the pryed open side then pry the other side and fully insert the pad you can avoid fully depressing caliper pistons... that being said I think my issue may not be only the pads , as the pads are dragging on the disk enough to impact freespin. I will ride it and if it does not work itself out I'm gunna need to bleed it :'( fudge fudge fude x2

[@JonanthonyTarlen]

@@WingsOfADream1put one in with the clip, take the brace out from the back. Get a mini screwdriver and pull the brake pad holder until you can get the other brake pad into place

[@davidpapp4140]

my pads keep falling out of their place how can i prevent that?

[@jesseespinosa9739]

Didn’t know it took a whole minute to remove bolts jeez

[@trexeater101]

I like how you used gloves 😂

[@user-uj3lg3uk9u]

Music annoying

[@danatool]

Top 👍 but stupid system

[@takecareofyourshoess]

Here's an idea....how about some actual spoken guidance rather than this ridiculously LAME music you've used here?? Would make the video 100X more useful.

[@joncrunk598]

Here's an idea....how about some appreciation and positive feedback rather than this ridiculously LAME self entitlement you've used here?? Would make the world 1000x more tolerable.