How to change iPhone 11 battery with health 100% using JC v1S

[@syedusman854]

Whate u did when u connect on battery strip the multimeter was not reading after it was showing???

[@melakaiphonerepair]

Test the battery voltage

[@MrSkar87]

after reset cycles,and put battery with tag for the first time,tag can be removed..and phone can read battery normaly

[@reezmanreezz3220]

Same for qianli icopy plus?(2.1,2.2)or apollo?

[@josephrobert2964]

@@reezmanreezz3220 waiting for the answer too

[@YusufAyinde-p7y]

Sir,I think you supposed to remover the tag from it ?

[@detroitrcwurks998]

When I go to change the battery in my pro max 12 which currently sits at 93% do I need some encoder device to reset the part that’s soldered onto my original battery…not sure name of it. I know I need to remove it and resolder it onto my new battery in order for battery health management to continue working properly. It counts the number of cycles uses that to determine battery health I guess but not sure if it needs to be reset or not. Good look’n

[@melakaiphonerepair]

Yes, encoder to reset , before batt replacement or after also can. Depend on u. 11 series and above need another small ui board then only can reset with encoder….

[@detroitrcwurks998]

@@melakaiphonerepair ok I’ll look into both encoder box and board than thank you. What’s your opinion on batt health accuracy. If this is using cycle count to determine health is it counting a full discharge and full charge as 1 cycle or is it counting a cycle every time you charge from 50% to 80%? Does anyone really know this question I can’t seem to find a solid answer. Appreciate you friend!!

[@muhamadhafiz-j2z]

before we assembly the lcd , should we take off the jc flex cable or just let inside it

[@melakaiphonerepair]

It was not possible before, but now there is no need to install it inside, otherwise you would have to buy a lot…😃

[@blackrepairs5978]

I have an iPhone that will keep showing the old data at 88%, I have tried connecting a different battery, rebooting and reconnecting the new battery with the transfered bms board again but to no avail. The new data won't show up whatever I do, have you come into this? I have done many replacements without issues with the same tag on. Thanks in advance for your reply

[@melakaiphonerepair]

What current version of the iOS? 17.4?

[@blackrepairs5978]

@@melakaiphonerepair yeah newest

Hi friend, can you explain what have you done beetween 9m30s and 10m10s?? Because i have the same problem, 0volts on the flat..

[@Kyros9119]

Try with a battery charging/activation board that has a button for activation, like the qianli megaidea charger 2.0, with the red board.

[@MrBoskyy]

Hi, good video but can’t you avoid connecting new clear battery and activate new battery (with bms changed) with jc programmer?

[@Layla.khanyar]

Qs is agr phone khareeda ho and us mai us bande ne repair krvaya ho yani battery nayi dalvayi ho and old battery avilable na ho toh kya kr skhate hai message gayab krne k leya purani battery toh hai nahi strip kaha se ayegi?

[@EkoRamendyBananZ]

So we need 2 bateries with BMS to do this trick ? can we just plug the original battery for the firt boot after programming the Tag on Flex ?

[@melakaiphonerepair]

Actually now already have new method. Easier to make it 100%. No need another battery.

[@janmatejcik7073]

​@@melakaiphonerepair hello, what is new method please?

[@EkoRamendyBananZ]

@@melakaiphonerepair thanks ! Can you share the method ? :)

[@nikmuhamadaqilnikatan2009]

why you using power direct from psu to show the "important battery message"? why not using the battery? that message appears because using power from psu, not battery. at 7:18 and at 10:48 it show that message

[@melakaiphonerepair]

That time I m lazy to use new battery. So power supply is the faster way for me. And now with version 3.0 tag-on cable, no need a new battery to shown “ unknown part “

[@chinaphonefixteam6300]

JC V1S Battery Repair Board and JC Battery repair flex cable for iPhone 11-13 Pro Max Battery Data Read Write Progamming to remove Health Warnning Error.

[@MaxwellCooper-rn4zd]

Mxa

[@sharmaxop]

if ur battry health is 84 and we have to change the battry cell but not change battry health then the important message will show or not. We just change and remains battry health as it is. Can we do this also?

[@melakaiphonerepair]

Some time it shown and some time not. Depend your luck.

[@isajakwa4059]

2024 ni masih boleh guna x? sbb sblm ni beli ay a108, xleh nk program battery, check guna tools, cun dh. bila plug in kt hp, masih BH yg lama. dh guna BMS lain untuk start, then swap battery, masih gak sama.

[@kmigellano]

I changed my battery and kept the 100% battery healthy but noticed that the battery health has drop quickly. I believe it is inaccurate though.

[@melakaiphonerepair]

Now batteries quality damn lower ….

[@airulazrie8424]

kalau bateri vol di tahap maksima perlu ke saya pakai battery activator tu. boleh ke saya pasang terus battery.

[@caffa_tech]

Hi, do I need an aftermarket battery or is a bench power supply suitable for activation?😊

[@melakaiphonerepair]

Now tag on v3.0 no need power supply to activate it. Just install battery to phone use cable to turn it on.

[@automotive9648]

What happens if i reset the battery capacity to 100 and also reset the cycles to 0 and then just plug the battery back? Will it show 100% in the settings??

[@melakaiphonerepair]

It won’t show 100% in the setting if u just plug the battery back.

[@automotive9648]

@@melakaiphonerepair what if i false start the phone with another battery first? thanks for ur reply

[@DiyfixtoolCi]

Great video, I learned a lot of useful things

[@melakaiphonerepair]

Glad to hear it!

[@rajaservicestation]

what you do when you check the battery connector dont have any value by multitester behind the camera? i have same issue here cant turn charge with original bms

[@melakaiphonerepair]

U can use power supply by 4.2v to short + n -

[@7fink7]

if you have detailed reviews on i2C i6 / Luban L3 mini / JC V1SE / Qianli iCopy , please? Can you share info. thanks!

[@melakaiphonerepair]

I only use jc brand. Others I never try before. But I think same thing….

[@7fink7]

@@melakaiphonerepair I need detailed review

[@dipacelombardoagustincom2245]

you need to have the latest version of the JCID software to recognize the battery ????

[@jaydanvandegeest2180]

How can you put it in the latest version?

[@hirohiro437]

Why is there a need to connect to another BMS?

[@melakaiphonerepair]

Because it’s encrypted, so need the bms to activate then only can modify BH and cycle count.

[@karim-sq1sk]

hi sir, thanks for this video please i want the link for buy this part charger you linked to battrie for charger

[@melakaiphonerepair]

i bought from taobao

[@karim-sq1sk]

Name the part plese or link on enay thanks sir

[@MaSter-sv3ir]

Do you have any idea why on some iPhones it’s showing 100% after we remove the battery repair flex cable and on some iPhones it’s showing the battery error as “battery not recognize” when we pull out the battery repair flex? All versions of 17.4.1 we use u3tools but below that shouldn’t be any issues.

[@melakaiphonerepair]

17.4.1 already locked down it

[@tacticalgamerat3745]

The small jc flex between the battery and the board, can i remove it after boosting the battery or do i have to keep it inside the mobile

[@melakaiphonerepair]

After boosting , u turn on the phone , if the battery health already 100% then u can remove it. No needed keep inside…

[@dylanmaki2482]

Do you need a flex for an SE 2020? Or just the iPhone 11 and up?

[@nirobbhuiyan580]

is there any way bro before or after buying a device i can see my device is boosted one?

[@melakaiphonerepair]

Connect to pc software named 3utools then will show exactly battery health.

[@jfixtechnology]

Boss...nk tnya sikit.. I ade tukar bateri customer IP xr dah tranfer ribbon..kemudian reset dgn JCID dah oo BH100%>> Selepas 1 hari jadi unknown part nitification... Phone tu ios16...knp ya?

[@kodeysazali9885]

Sebab ios bro ,

[@umar5385]

iOS 16 dapat detect bateri tak original kan?

[@gerrit9106]

Is it possible with iOS16?

[@syedusman854]

Wt u didi when u cannect multimeter on battery first it was not showing after that it was showing wt u did??

[@melakaiphonerepair]

The new battery cell was “sleeping” after welding, i used power supply (4.2volt) to “wake up” it.

[@Jmgb064]

If you dont use that adaptar formas jc dosent the perfectamente go up or its just for programming?

[@melakaiphonerepair]

Thks for watching

[@lulslime1066]

It has to be programmed . Even with an original battery has to be programmed

[@AyieMobileTech]

Antara channel youtube yang saya jadikan contoh

[@melakaiphonerepair]

Terima kasih! bro !

[@dedikrohmahtuloh6603]

If i just reset the cycle and battery health with jcid without change the original battery, what is this change status on iphone?

[@melakaiphonerepair]

Health will be 100%

[@dedikrohmahtuloh6603]

@@melakaiphonerepair ok thank sir

[@PolaPot-r3c]

Boss brp cost repair

[@mohfod7206]

boss masa voltage x keluar dkt ribbon tu apa yg kena buat ya sbb masa ni boss x tunjuk. huhu

[@melakaiphonerepair]

Voltage x keluar , pakai power supply activate batt

[@fazrulhaizal6174]

Klu xda power supplier, masuk battery dkt fon lepas tu sambung cable cas pon blh juga.

[@melakaiphonerepair]

@@fazrulhaizal6174 ya. Blh juga. Repair fon xde power supply , pelik juga ni….

[@ataganapatrick3557]

You are supposed to interswitch the battery booster negative to positive to restore current back to the battery

[@mejhafizhamiditudm829]

bos kene letak battery lain dulu ke? mula2 tu bos letak x jd. lps masuk bateri lain dlu, bru jd

[@melakaiphonerepair]

Skrg ade version baru, x pyh masuk battery baru. Selepas u dah program, pakai cable turn on fon dulu. Lepas battery msg keluar, restart fon ont the spot. Then battery health akan 100%

[@umar5385]

@@melakaiphonerepair Adakah bateri health akan sentiasa tunjuk 100% walau kite dah guna beberapa tahun?

[@teunnevels2288]

Hi, if i Connect battery with tag-on flex to JCID V1S, i cannot activate battery. Also not possible via JC repair SW. Can You help me?

[@Alcup]

Same problem

[@teunnevels2288]

@@Alcup any luck on your side?

[@melakaiphonerepair]

Can. Which model u mean?

[@teunnevels2288]

@@melakaiphonerepair I updated JCRepair by downloading it from their website and now I can activate.

[@carlosgohn8659]

Hello one question,the flex between batterie and jcbox,it used just for one battery or the flex Can it used eveytime ???

[@melakaiphonerepair]

Can use every time

[@wucollins1727]

@@melakaiphonerepairwhere can I get the flex?

[@wucollins1727]

@@melakaiphonerepairis it going to come with jcid programmer? Cos I just ordered mine

[@dhraytechpoweredbyolyceneg9779]

hello, ive been doing this but not working though i used after market battery that i remove the battery board of the new battery. what am i doing wrong , i need someone to guide please

[@melakaiphonerepair]

Do u have programmer and tag on ribbon ?

[@RBlacklightR]

Where do you get your batteries from , or what battery do you recommand for ip 11 ?

[@melakaiphonerepair]

I bought from my local suppliers. Original cell.

[@kodeysazali9885]

@@melakaiphonerepair yeah with price tag rm40 lol

[@dipakshah7387]

@@melakaiphonerepair original 😂😂😂😂😂

[@umar5385]

Bateri gred apa?

[@loybots4624]

How to know if battery have undergone boosting?

[@melakaiphonerepair]

After shorted by power supply then test with multi tester voltage

[@bjayflores8830]

What type of soldering iron is that? And the brand pls

[@melakaiphonerepair]

Welding machine . Brand i2C

[@leonking9852]

@@melakaiphonerepair can you share the link where to purchase

[@havalrasool7353]

what happened if you don't have original battery?

[@melakaiphonerepair]

Then you can only choose Apple original part.

[@MindfulBytes09]

Sir help me i have replaced my 12 mini battery but it’s showing old data my battery health is 69% before replacement and after replacement its still 69% how can i fix it

[@melakaiphonerepair]

Do u have that machines and small plate ?

[@pthaokip5246]

Does the battery last longer when you increase to 100% battery health compare to 78%?

[@melakaiphonerepair]

No… must change new battery

[@melakaiphonerepair]

Sure, battery performance like original.

[@markmata2671]

100% maximum capacity is obviously better that 79%. However, 79% is not the end of the world. It just means that your batter will drain faster throughout the day. If you have the money to change the battery, do it. Especially if you’re on a tight budget and can’t buy a newer phone.

[@KingsandPawns]

Mine is 70% and phone is just fine-

[@ax____761]

Me with 79%

[@nofelrawat7763]

Where do I buy the small JC flex

[@melakaiphonerepair]

Aliexpress

[@gagnapplefix]

Good job 👌👌

[@repairphonebergerak]

Tag on flex to kena pasang sekali battery ka n bagi customer selepas dh tranfer ribbon n copy data

[@melakaiphonerepair]

Skrg dah x pyh pasang lagi

[@e-jumpprojexx8005]

Bos...ada buat kelas tukar bateri iphone sekali buat Bateri health x?

[@melakaiphonerepair]

I x buat class battery. Internet banyak mcm2 video ajar

[@gerrit9106]

I did the same for my phone. Have had it working for 2 months now and my battery capacity has already dropped to 91%, why is this happening so fast? Is this normal?

[@melakaiphonerepair]

Yes, depend how u use the phone. Do not charge while playing the phone…. Do not use the phone when getting heat up…..

[@SH-ef3xp]

My iPhone 11 Pro recently had charging issues and technician removed the battery. While reassembling he did not put any Adhesive back of battery. Now I feel my battery is heating a lot. Does it because of no Adhesive back of Battery? Do Adhesive act as thermal paste like the one we use in case of computer processor??? Please let me know and also if you can share a buying link…. Anyone else facing similar issue??? Please reply in detail

[@melakaiphonerepair]

There is no direct relationship between the battery adhesive and the heating problem of your mobile phone. The adhesive only fixes the position so that the battery does not shake. The purpose of the thermal paste is to dissipate heat, and it is not sticky. Your problem should be searched by a more professional person in your area. I hope my answer can help you.

[@livevilstudios3725]

What is the name of the device which u are using for resetting battery cycle

[@melakaiphonerepair]

JC programmer device V1S, new model is V1SE

[@kushagrame]

3utools can detect it or not

[@melakaiphonerepair]

Cannot

[@kwtm]

Nice

[@melakaiphonerepair]

Tq

[@ramzeesafwan7538]

Melaka area mana

[@melakaiphonerepair]

Melaka raya

[@repairphonespecials]

bos paano mag order tools icopy battery health?

[@melakaiphonerepair]

English please

[@irizbirujrb6684]

12 pro how much boss?

[@melakaiphonerepair]

Hi… R u Melacan?

[@irizbirujrb6684]

Jb boss

[@melakaiphonerepair]

@@irizbirujrb6684 sini Melaka. I buat rm250.

[@aviekoza1388]

Why iphone battery are very weak compared to that of Android phone??

[@melakaiphonerepair]

In fact, they are all the same, but the battery health is not displayed in the Android phone, so you will not notice that the life of the Android battery is reduced.

[@arround1]

Good job!

[@Vondereich]

Ada pasang waterproof seal x bos kalau tukar bateri 11 ni?? Berapa harga? Melaka area mana?

[@melakaiphonerepair]

Hi…. Ade pasang seal waterproof, tapi c janji ia betul2 waterproof ya….. kedai i melaka raya. Kalau nk location Wsapp nombor ni, wa.me/60167100231

[@Vondereich]

@@melakaiphonerepair ok nanti i cari you.. bateri dlm 84.. tggu turun skit lagi nanti tukar :D

[@danielnongrang3826]

How much it will cost to change battery

[@melakaiphonerepair]

Hi, where are u from ?

[@paulotamidles3722]

my ios battery health is decreasing it has 69 % percentage of battery… can u faxed it? i want to change it a new battery so it’s up to 100% percentage… my ios didn’t even reach 1 hr or 2 hrs - ang bilis po kasi ma lowbat. 😢😢😢

[@melakaiphonerepair]

Sure I can do that…..

[@cikhijau617]

Suhu brp bos solder itu

[@melakaiphonerepair]

I x pakai solder pun

[@retickfrompl4451]

nice vid

[@AyieMobileTech]

Bang benda tu mana nak beli

[@melakaiphonerepair]

Boleh beli kat shopee

[@eangrace9497]

Boss, lepas program, boleh cabut tak tag ni?

[@melakaiphonerepair]

Boleh… tag simpan next coming 👍

[@eangrace9497]

Mantap bos

[@Али-у2в1х]

And is it working stable, no restarting, fast recharging, ios ota update fail ? Without jc flex keep inside

[@melakaiphonerepair]

Yes. All working fine.

[@3Glive5082]

Hello bro.PLEASE TELL ME! IF CHANGE MY IPHONE BATTERY AM I NEED TO PICK IT TAPTIC ENGINE OR NOT? Please Tell me! I’m going to change battery of my iphone!

[@msaiful9864]

No need

[@topzin6218]

Qual nome desse ferro de solda ? Alguém sabe ?

[@sultan26706]

Spot welder

[@sultan26706]

Spot welder

[@pandaboyy.t3724]

Bro location

[@melakaiphonerepair]

WhatsApp wa.me/60167100231

[@cikhijau617]

Kena pakai suhu brp untuk solder tu bos?

[@melakaiphonerepair]

Şuhu? Solder battery ke?

[@phytech6999]

perfect bro

[@melakaiphonerepair]

Thks ya

[@BloomfieldBlanche]

Thompson Shirley Perez Matthew Johnson Frank

[@mr_deejay______]

Hello sir apka address mil sakta h please?

[@melakaiphonerepair]

English please

[@A1INFORMATIONTECHNOLOGY]

People are now doing it without changing the flex cable, please do you know how ?

[@melakaiphonerepair]

Yes…. After confirm new battery is 100%, then can direct unplugged the small board.

[@TOMMYNATROSARIO]

Why after remove the jc tag the phone shows again the old battery health? Can you do a tutorial removing the jc tag please

[@iavenuemobileshop]

After completing all steps battery is showing 100%health i am done all after restarting phone i am getting problem sometimes phone switched off automatically sometimes faceid not working sometimes phone is getting restart plz help me

[@jarjarbinks77]

Sounds like you might have damaged the earspeaker flex.

[@Vinship14]

Nice Man.

[@melakaiphonerepair]

Thanks!

[@BloomfieldBlanche]

Lee Margaret Rodriguez Sandra Lopez Susan

[@syahrilfarhan4423]

Berapa harga buat ni ya

[@melakaiphonerepair]

Rm230

[@muhamadaiman7234]

amat lama nk buat 😂😂

[@melakaiphonerepair]

Lama2 akan jadi faster….

[@jaromirzamecnik3983]

OMG - such a mess on the table.

[@melakaiphonerepair]

Haha….a lot of works bro!

[@umairaatif9446]

❤️❤️🙌

[@슬픈악마-u5o]

요즘 나오는 대용량 베터리도 가능한지 궁금하네요, 어째든 설명이 매우 좋네요!!! 보기만해도 이해가 됨

[@melakaiphonerepair]

annyong haseyo. 네, 배터리가 크면 더 오래갑니다. 제 영상을 시청해 주셔서 정말 감사합니다.

[@RemLabsSPB]

ногти подстреги

[@melakaiphonerepair]

English please. Have a nice day bro 😎

[@guifregibert]

you should trim you nails

[@melakaiphonerepair]

Thks for your comment 😇

[@zero4961]

gross nails 💅

[@zolyniakk]

cut your nails pls

[@melakaiphonerepair]

Haha…

[@earll9586]

p̳r̳o̳m̳o̳s̳m̳ 🤘