how to check solenoid coil work | connections and testing with multimeter .

A solenoid consists of the coil, the tube, and the armature. The solenoid coil is working in the circuit and can be worn out. As the main part of a solenoid, solenoid coil is replaceable when it’s not working. But how can we determine it is good or bad?
Here is the way to check solenoid coils with a digital multimeter. A typical digital multimeter is used to measure voltage (volts), current (amps) and resistance (ohms). It is a tool easy to use for diagnosis in the electrical industries.
1.What is a solenoid coil?
2.What are solenoid coils used for?
3.What is the difference between a coil and a solenoid?
4.What causes solenoid coil failure?
5.How do you check if a solenoid is working?
6.How many ohms should a solenoid coil have?
7.Can you test the resistance of a solenoid coil?
8.How many ohms should a 12V solenoid have?
9.Do solenoids have resistance?
10.Does a solenoid have continuity?
Step 1. Set your multimeter on ohms. If the multimeter is not automatic, set it on 2k ohms.
set multimeter
set multimeter on ohms
Step 2. Place the probes of multimeter across the pins of a solenoid coil. If you find 3 pins there, one of them is a flat pin which is connected to the ground. What you need to do is connect the other two pins with the multimeter.
solenoid coil
solenoid coil
Step 3. Read the number on the multimeter. A functional solenoid coil normally has its resistance within a certain range. This range varies from manufacturer to manufacturer, but definitely not zero. If you have 0 ohms, it means the coil is shorted. While the infinity read indicates the coil is open, the wire is broken inside.
multimeter read
multimeter read
Particular cases. Sometimes you find a normal read on the digital multimeter but the coil is actually not functioning. At this time, you can use a screwdriver and put it near the armature then energize the solenoids. If there is a magnet in the presence, the coil is good. Otherwise, it is bad, and you need to change a new one.
You will find it’s easy to test a solenoid coil follow the rules above. If you do have a bad solenoid coil, replace it with a new one. It’s very easy to change a solenoid coil.

[@hosapiangami866]

Good advice.Thankyou sir, for your support.

[@shrikantchavan7531]

Good knowledge with Idea..

[@anjumnaaz3276]

Very informative

[@RohitSharma-ye7wn]

Very very helpfull video fentestic

[@FarukHossain-dv9dt]

Thank you bather

[@MaheshSingh-px8tk]

Bahut sundar

[@laboratoriocotear1949]

You shouldn touch the wire with both hands because you will measure the resistance of the coil in parallel with your body´s. In this case the measure ir quite correct cause your body resistance is in Mohm order and the coil is 70 ohm, but is a good practice to consider

[@masudsikder7079]

Thanks sir

[@aminulsheikh4210]

good Sir

[@sabnamakhtar6844]

Nice

[@narayanhandal4480]

Nice sir jee

[@gursangatkalsi1982]

Nice video.

[@engineeringconcepts]

Many many thanks

[@jaishivajijairayanna7940]

Super sir

[@rohitpandey4596]

100 likeee kar diye sirrrr😎....nice explaination

[@engineeringconcepts]

Thanks dear

[@sushilkanttiwari915]

In a solenoid coil voltage is showing 18v. but cylinder is not operate ,though there is no problem in cylinder. What may the other cause.

[@RAKESH-hm1mv]

👌👌👌

[@HuNtER-vo5ox]

What is sonlight valve Ragistance?

[@RohitSharma-ye7wn]

Sir plz reply me mere ase hi ak cool hai aur jb hm usko lagate hai to vo burn ho jati hai 3 coil jal chuki to sir hmara kya systm h jo coil bar bar damage ho jati hai

[@ravisaini6888]

Sir 24 VDC coil kitna current carry karta hai

[@amittilara1797]

If coil resistance is 75 ohm but magnetic field not forming, then what could be problem in solenoid

[@laxmikantmishra3265]

Bhai CNG me yah coil bahut heat karne lagta hai 10 minutes me is ka solutions kya hai

[@MOHAMMEDABDULLAH-jd1dh]

How to check when it is in service or pipe line

[@aamirawan7998]

Checking continuity on a coil/winding?? Why would you get continuity on a winding? You should only get it if it the winding is shorted and the resistance has dropped.

[@GulabKhan-tp3qy]

Good morning ji

[@engineeringconcepts]

Good morning

[@GG-jo2qo]

How to check if the solonoid valve is 220v ac or 24v dc?

[@mixz9929]

Should say on the coil

[@nicola2375]

how to repair

[@mithileshkumari7514]

Sir iskki resistance value bhi checkk kar sakte hai

[@engineeringconcepts]

Yes dear

[@gursangatkalsi1982]

Sir, how to detect wheather soliniod coil is ac or dc operated....?

[@MOHAMMEDABDULLAH-jd1dh]

Check the name tag in sov

[@zeeshanansari7076]

Sir agar solenoids bahut garam ho Jara hai to Kiya Kiya Karan ho sakte hai

[@engineeringconcepts]

LOOSE CONNECTION HO SAKTA HAI ,

[@altafshaikh3771]

Sir 220v coil bar bar kyu short hojata hai kya problem ho skta hai

[@engineeringconcepts]

Loose connection hai check karo

[@RohitSharma-ye7wn]

Kyo bar bar jal rahi hai coil @@@110 voltage ki hai sir

[@swatibahikar1143]

Main एरिया लाईट की कमी भाष्या किलर नाही

[@roopeshchourasiya4520]

Sir इसका कवाई ल मिलेगा क्या

[@abhindarji]

हमारे या हर प्रकार के coils बनाए जाते है तो किसी भाई को चाहिए हो manufacturing rate पर बिना किसी कि commision से तो reply kre

[@roopeshchourasiya2277]

Coil ka price kyaa h sir ji

[@nicola2375]

तुम्हारा नम्बर भेजो

[@multitechnician461]

Voice shound is slow

[@RohitSharma-ye7wn]

Sir plz reply me

[@user-sj6md6zj9p]

Whay you put English title when you speak I dian. Who can understand you