How to Clean and Paint a Rusty Trailer Frame

Welcome to my channel, Homes for Beginners where I show you how to do repairs around the house yourself. Please don't forget to hit that LIKE button and SUBSCRIBE for future videos.
In this video, I will be showing you how to repaint a rusty trailer tongue and you can also use this same process for a whole frame. If yours is dirty or greasy, then I would recommend washing the trailer with a degreaser and then allow it to dry for a couple days in the sun. Remove any components so you have fewer items to work around or mask off. For this, I removed the wiring and then the tongue jack.
Here are the Amazon links for some of the products used in the video:
USA:
Wax and grease remover: amzn.to/2M6xvCV
220 grit sandpaper: amzn.to/3sZf5V7
Safety glasses: amzn.to/3b3xMix
Rubber gloves: amzn.to/3tXng51
Paint brushes: amzn.to/3qpPLWW
Wire brush: amzn.to/2Mx5F35
Cup wire wheel: amzn.to/37dDq0e
Canada:
Wax and grease remover: amzn.to/39nLn4F
220 grit sandpaper: amzn.to/2YjmoJe
Safety glasses: amzn.to/37hVPJw
Rubber gloves: amzn.to/2NpGwHF
Paint brushes: amzn.to/3akF0Q7
Wire brush: amzn.to/3cOcWpW
Cup wire wheel: amzn.to/3tW123g
Cleaning off the rust and there is a variety of methods that can be used, I’ll be using an angle grinder with a wire wheel. This cleans up the surface fairly quick, these cupped wire wheels aren’t overly expensive, and the wire wheel can clean up any pitting as well. Other options can include media blasting, DA sanders, chemically, and there are even some paints on the market that can encapsulate rust, however, they can be more expensive.
I am using a form of rust paint, however, I still prefer removing a majority of the rust. If you have any scaling, a needler can be used to break that up. Or if you don’t have access to one, then hitting the surface with a ball-peen hammer will work just fine too.
Once you’re done with the wire wheel, next is sanding this surface. This can be done by hand or using a machine sander. For this, I am using a hand sander with 220 grit sandpaper. This will remove any rough edges on what's left on the existing paint and provide a surface where the paint can properly adhere to.
Any hard to reach areas can be cleaned up using a wire brush first to remove any scale, peeling paint, and rust.
Then finish up using 220 grit sandpaper by hand. Even abrasive pads can be used if you wish with the appropriate grit rating.
To get a bit of extra height and work around the hitch portion, I clipped the trailer on the truck. To clean off any dust, use either compressed air or the blowing feature on a vacuum cleaner.
Now wipe down the surface using a wax and grease remover with a clean cloth. Any contaminants on the surface, this can include anything from dust, oil from your skin, grease or lubricants, etc will cause issues with painting. The paint can separate, cause application issues, peel or crinkle.
Next is taping off any areas you don’t want the paint to come in contact with. I’m applying the paint by hand so there are no worries about overspray.
Moving onto the paint, there are various types available on the market, however, I’ve been quite happy with this stuff. I purchased this from the local farm equipment supplier, the John Deere dealer to be exact and it’s a bit pricey compared to other paints, however, it applies nicely and is extremely durable. This is a low gloss version and it does have rust inhibiting qualities. Mix the paint accordingly. No primer is needed with this paint, it can be applied to bare metal. This can vary between products, always refer to the application instructions just to be safe.
I am using a roller tray lined with tin foil for easy cleanup. I did thin out the paint slightly using the recommended solvent.
First is applying the paint to the hard to reach or uneven areas. Basically, the areas where the roller can’t reach. To paint the rest of the tongue, I’m using a foam roller. This will leave somewhat of an orange peel texture which I personally think looks fine and will hide any imperfections on the surface. The paint will need to dry for about 20 minutes and this can vary depending on the thickness and temperature.
Now using a new roller and applying a second coat. Being that I thinned this out slightly, it doesn’t tend to cover as well. Once this final coat is on, if you have any tape right against the paint, it’s best to pull that off immediately so the paint has a chance to flow and doesn’t cause a hard line. Depending on the thickness of paint and the temperature, you should wait for at least 48hrs before the paint is fully dried, then reinstall any components that were removed.
© Homes for Beginners 2019
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

[@homesforbeginners]

Here are the Amazon links for some of the products used in the video: USA: Wax and grease remover: amzn.to/2M6xvCV 220 grit sandpaper: amzn.to/3sZf5V7 Safety glasses: amzn.to/3b3xMix Rubber gloves: amzn.to/3tXng51 Paint brushes: amzn.to/3qpPLWW Wire brush: amzn.to/2Mx5F35 Cup wire wheel: amzn.to/37dDq0e Canada: Wax and grease remover: amzn.to/39nLn4F 220 grit sandpaper: amzn.to/2YjmoJe Safety glasses: amzn.to/37hVPJw Rubber gloves: amzn.to/2NpGwHF Paint brushes: amzn.to/3akF0Q7 Wire brush: amzn.to/3cOcWpW Cup wire wheel: amzn.to/3tW123g

[@edvanmil269]

I've used Rust-Oleum 7777502 Protective Enamel Paint, Black Satin Finish and found it to be as good as the John Deere paint mentioned in the video, but far easier to obtain and a little cheaper.

[@trep53]

Just finished painting my boat trailer. Basically used the same method you did. My trailer is “C” channel construction and using a 2-1/2” wire cup in there was effective. One idea I had was to use a spray bottle to apply the degreaser which worked great and was easy to get enough degreaser on the frame without overdoing it.

[@c50ge]

Between coats I take my roller off the handle and drop it in the paint so I can use it on several coats. I’ve painted a truck and several tractors with this method. Between coats (give it a day or two)I lightly block sand and remove about 1/2 of the orange peel then apply another coat. I usually do three coats with the last coat I do not sand. The nice part about using a roller is there is no overspray in my garage.

[@homesforbeginners]

Great tips, thank you for sharing!

[@alexderus7480]

Turned out great. All of your prep work here was the key.

[@homesforbeginners]

Thank you so much!

[@QMil-sz8ej]

Great job man that looks really good. Will be doing my trailer this week. Thank you for help

[@homesforbeginners]

Excellent to hear and thank you!

[@henrydixon3159]

Great video if a trailer has flakes with rust and has been cleaned properly with a wire brush do need to use a primer on the surface

[@homesforbeginners]

Thank you! The type of paint I used, it doesn't require a primer. Depending on which paint you're using, refer to the instructions as to what is required.

[@frankzee111]

Thanks bro, I'm going to use this method to freshen up my trailer hitch!

[@homesforbeginners]

No problem!

[@1mach28914u1]

I like the tin foil idea, I’ve never thought of that before.

[@arturosarmiento5686]

Definitely, great idea.

[@michaelpaul721]

great job - very well explained, gave me some good options. Thanks!

[@homesforbeginners]

Glad it was helpful and thank you for the feedback!

[@VJolie3]

beautiful job

[@homesforbeginners]

Thank you!

[@surajvirajrajvirbalgobind7985]

Nice Job, only i'm missing the primer here. After a good cleanup i use a havy duty primer, cauz the trailer is always outside and only painting it 2 coatings is not holding the rust out of the paint. Using a primer ( hamorite) is prefereble i think.

[@ProjecthuntanFish]

Great video with great advice thank you for posting

[@driver209]

Nice!!! Thanx for sharing 😊

[@craigbosel7887]

thanks mate, that was very useful

[@homesforbeginners]

No problem, happy I could help!

[@FB-pk9ob]

Great!!!

[@homesforbeginners]

Thank you!

[@fullsack]

probably using John Deere Blitz Black Paint

[@gloriafavor4148]

NICE NICE WOW

[@afishyfella]

Can you share the name of the paint? I watched the video twice and viewing the video description, but didn’t hear or see the name of the paint.

[@TheFoezee]

Im doing a 75ft trailer. It’s gonna take me a while to remove the rust

[@AndyBuilds]

What was that yellow rectangular can that you dripped a few drops into the paint? Great video thanks for the tips

[@homesforbeginners]

Thank you! That's a paint reducer.

[@stuartmenzies3928]

Exellent

[@homesforbeginners]

Thank you!

[@mikeprice7124]

Great job! Love that accent btw. Are you from Maine?

[@homesforbeginners]

Thank you! Nope, I'm from Canada.

[@TheRelger]

My buddy got a wire from a wire wheel in the eyeball. He was in a lot of pain.

[@homesforbeginners]

Safety glasses are a must.

[@roderickdouglas1048]

What was the actual name or type of paint? Nice!

[@adamstrickland3440]

I am not 100% sure but I believe it is John Deere Blitz Black paint. My dealer said that is what the matte black was called

[@jordanbridges693]

What's the name of the paint you used

[@dmitryprosviryakov2034]

What about the frame under trailer

[@driver209]

Did you do two coats or is one enough?

[@iflytango]

Is this some kind of magic paint

[@homesforbeginners]

Could be, I really like the stuff. It's a bit more pricey, but it's worth it in the end.

[@rafaelrengel6935]

What paint did you use? Primer?

[@homesforbeginners]

No primer, the paint I used can be applied directly to metal. It's a farm implement paint, to be specific it's from the John Deere dealer.

[@Majsumreen]

Just wanted to know what product did you use,the name of it and the other product plz

[@homesforbeginners]

The only products that were used was the wax and grease remover which is just a cleaning solvent. And the other was farm implement paint, the stuff I got was specifically from John Deere. They only have one type of implement paint, just the colors vary.

[@skinlab4239]

@@leadpill8333 almost all equipment paint is just oil based paint. Almost every paint place has it. About eight bucks a quart for Rust-Oleum at lowes here.