How to clean MAF sensor on Toyota RAV4

  Рет қаралды 81,858

Toyota Maintenance

Toyota Maintenance

Күн бұрын

Пікірлер: 91
@asmith6173
@asmith6173 4 жыл бұрын
Saved me $70!!! I can’t believe the dealer charges $70 for this “service” and it’s so easy! Thank you for sharing your knowledge.
@gregnixon1296
@gregnixon1296 4 жыл бұрын
As a thank you for buying one of their cars, dealerships will overcharge you every chance they get.
@BabyGangsterIsMe
@BabyGangsterIsMe 3 жыл бұрын
my toyota dealer in virginia charges 150 bucks to clean MASS AIR SENSOR..so lucky i know how to do it..if not, they rip me off...
@davehayden1282
@davehayden1282 Жыл бұрын
They don't call them Stealerships for nothing.
@jaysitu6968
@jaysitu6968 Ай бұрын
Now is 298$😂😂
@dtna
@dtna 4 күн бұрын
Dealerships will ( ▪︎ ) you!
@erikcox1947
@erikcox1947 4 жыл бұрын
Whenever I clean my sensor I like to take the air tube off and clean any of the dust and residue that my be inside. I also clean the the throttle body at that time but that is just me. Why not? You are already there. Keep up the good work my friend.
@angelbluerider9588
@angelbluerider9588 4 жыл бұрын
What you use to clean the air tube ?
@zumik83
@zumik83 4 жыл бұрын
With 10 dollars you can buy 2 liters of isopropyl alcohol 99.9% and you can soak the MAF in 100 ml or so for about 15 minutes. You can also give the MAF little shakes from time to time for better results. That way, those 2 liters will last you 20 cleaning cycles not just 2.
@erikcox1947
@erikcox1947 4 жыл бұрын
Good point. You can also put the isopropyl alcohol in a small spray bottle and spray it if you dont want to take the time to soak the sensor.
@zumik83
@zumik83 4 жыл бұрын
​@@erikcox1947 You could do that too, but it is best to let it soak, like dishes or clothes, haha.
@lane4574
@lane4574 4 жыл бұрын
They are not PH1 phillip head screws , Toyota usesJIS (Japanese Industrial Standard B 1012) exclusively. They have the PZ1 , PZ2 , etc. etc. They are available on Amazon or Ebay , for 10.00 or less for a cheap set.....I'm surprised you didn't know that ? But not many people do.....I clean my MAF every 3k , and spray the same CRC MAF cleaner , but I also use a fine hair artist paint brush , and gently wipe the metal sensors off with the fine brush. Road grime , oil , even pollen , etc. etc. Ive done this for years , and cleans it better than just spraying it....Then I put dielectric grease around the gasket and connection plug...I even put Marine grade heat shrink insulation at the base of the connector , where the wire cover (Flex Tubing) always separates from the end , exposing the wires at the connection. (Not bare wires) because of the heat from the engine....And I do the Coil connections with the marine grade shrink tubing. It has glue on the inside to make it water tight....Just a little info for ya....Peace.
@lane4574
@lane4574 4 жыл бұрын
@Peter Rudy Yeah , I've heard it from many of mechanics , and heard a lot of em say they gently clean with a fine hair detail paint brush, after soaking it with MAF CRC several times . I've been doing it for years and haven't fkd one up yet. You can sure tell that its clean with throttle response , Air/Fuel. I found that resetting the Ecu/Ecm helps it to adjust better with a blank slate. Just from my personal experience working on my Tacoma and what ever make vehicle.
@markreynolds3850
@markreynolds3850 4 жыл бұрын
Thanks for sharing your video,I enjoy your approach to fixing things.
@vladkalina69
@vladkalina69 4 жыл бұрын
A word of information. I understand that the Japanese motorcycles use JIS screws that look like Robertson or cross style. JIS or Japanese Industrial Standard are the correct fit I would expect for the Japanese Car. The advantage or the JIS over the Robertson is the torque is more effectively used on the JIS. Using Robertson on JIS may work but may be prone to stripping the head of the screw. Love your videos.
@mannyroias3392
@mannyroias3392 4 жыл бұрын
I do this in my corolla once a year great video!
@ralanham76
@ralanham76 4 жыл бұрын
That seems like a lot. Seems like waiting for the problem would be better.
@joshhemingway7294
@joshhemingway7294 2 жыл бұрын
You think that’s a lot? I clean mine every 3 months;) just a few sprays of course
@tomwalma4762
@tomwalma4762 4 жыл бұрын
New air filter is a must.
@alungibbon9146
@alungibbon9146 4 жыл бұрын
Half a cannister of maf cleaner seems excessive?
@Arjuna86004
@Arjuna86004 4 жыл бұрын
The exterior wires are only part of the sensor. The other part is in the tubes. Spray cleaner on both the exterior sensor and down the tubes to clean the other parts that you can't see.
@stevesneed56
@stevesneed56 4 жыл бұрын
Thanks for the video! I have a 2001 Tacoma with 190,000 miles ! Running a little ruff on idle, but smooth on the highway! Will try cleaning the sensor !!
@Zeek800
@Zeek800 6 ай бұрын
Clean your throttle body while you’re at it. Use throttle body cleaner for that and MAF cleaner for the MAF sensor.
@willc3586
@willc3586 6 ай бұрын
You may have to do the idle relearn. If you've changed the battery and didn't do it sometimes they will idle rough. There's videos on the Toyotas of how to do it.
@1ronhall
@1ronhall 4 жыл бұрын
Nice video friend ...... I may need to hunt around for the MAF on my Tundra. I bet each of these simple services make the performance just a little bit better!
@rightlanehog3151
@rightlanehog3151 4 жыл бұрын
Peter, I want you to know that if I ever find myself in California and my car needs service , I will wipe down the engine BEFORE I bring it to your shop ;)
@johnfitbyfaithnet
@johnfitbyfaithnet 4 жыл бұрын
Haha
@wudger901
@wudger901 3 жыл бұрын
Would be useful to hear what symptoms the car might have that would prompt this cleaning and/or a recommended interval. Thx
@moonuk
@moonuk Жыл бұрын
I belive .. Hard to start, stalls after start low revs .. Are a sign
@walterjunovich6180
@walterjunovich6180 3 жыл бұрын
Good video ! 😲👍👍👍 NEVER , NEVER, NEVER use Carburetor cleaner on your maf sensor, the petroleum distillates will screw it up !!
@sejinoh1970
@sejinoh1970 Жыл бұрын
Fantastic video. Is the chemical you used (Mass Air Flow) sensor same as Throttle Body Cleaner?
@jayhockley8841
@jayhockley8841 Жыл бұрын
No its not . Use MAF cleaner only .
@FredTheLutinoCocatiel
@FredTheLutinoCocatiel 4 жыл бұрын
Wouldn't you want to clean the throttle body at the same time with the sensor removed?
@Zeek800
@Zeek800 6 ай бұрын
Cleaning the throttle body will often increase cold start rpm. That should return to normal cold start rpm after 2-3 hours of driving or less. Cleaning both these parts using the proper cleaning liquid for each one ( throttle body cleaner for the throttle body ) should provide a smoother idle and may even slightly increase your fuel mileage.
@vasildimitrov6661
@vasildimitrov6661 8 ай бұрын
Thank you for the tutorial, so easy to follow! Quick question, could the MAF sensor cause the car to start rough and crank longer than usual only on cold starts?
@arieswaters
@arieswaters 8 ай бұрын
What is that part that's got all the little tiny holes in it that he's not showing here
@johnhefter3815
@johnhefter3815 6 ай бұрын
Trying to clean throttle body on 2013 RAV4 I finally got the clamp off above the throttle body but I still cannot get the plastic hose separated from the throttle body.
@martinwilliams6069
@martinwilliams6069 2 жыл бұрын
Hi, thanks, great video. What telltale signs are there telling you that it needs cleaning?
@merlinsosa9556
@merlinsosa9556 4 жыл бұрын
Excellent to-the-point video, Peter. If I may ask, what is the normal range during standby idle? My 2000 RAV4 is a little over 2000 RPMs w/ an error code of P0505 - Idle Air Control System, any advice would greatly be appreciated. Stay safe, everyone!
@madcowusa4277
@madcowusa4277 Жыл бұрын
Sienna with 240,000 miles. Figured it'd be a good time to do this. lol.
@thomas9469
@thomas9469 2 жыл бұрын
Can u please advice me something my friend I have a 16 tab 2.5 L. After I cleaned the sensor and installed the back side of the o- ring is slightly up Does the o- ring completely go inside the hole ? Please advise.
@Calvin7007
@Calvin7007 4 жыл бұрын
Thank U Sir, From Chicago IL😎
@treedeblue
@treedeblue 4 жыл бұрын
This pretty much is a good guide for most modern cars.
@andregouvea1866
@andregouvea1866 8 ай бұрын
Hello, from Brazil. I have a Rav4 2010. Where is located the MAP sensor? Please. I’d an inkling it is needed to be cleaned.
@stevenbauer7744
@stevenbauer7744 4 жыл бұрын
Do Toyotas also use JIS screws?
@lane4574
@lane4574 4 жыл бұрын
That's what those were lol....Good catch. Read my comment and you will know you were right on the money.
@davidnull5590
@davidnull5590 4 жыл бұрын
"JIS screws" Most of the people here on KZbin have no idea what they are; they think JIS is identical to US standards like Phillips #1 "Japanese Industry Standard: Often improperly referred to as Japanese Phillips. Commonly found in Japanese equipment, JIS looks much like a Phillips screw (and even more similar to Frearson), but is designed not to cam out and will, therefore, be damaged by a Phillips screwdriver if it is too tight. Heads are usually identifiable by a single raised dot to one side of the cross slot. Most people and companies outside of Japan have absolutely no idea what they are. With the similarity in appearance to the Frearson and the Phillips the screws are often damaged in removing and installing with the wrong tools. JIS tends not to cam out like Phillips. The JIS driver can be used on Phillips quite easily but not reciprically (sic). Drivers are not easily available in North America, try your local RC Airplane hobby shop. Most RC Helicopters use JIS screws to mount the propeller. JIS-spec cross-head screws are generally marked with a single raised dot or an “X”. JIS always fit Phillip fasteners, but because of slight design differences, Phillips drivers may not fit JIS fasteners. (unless the tip is ground down a bit)." www.motorcycle.com/ask-mo-anything/difference-between-japanese-jis-phillips.html
@lane4574
@lane4574 4 жыл бұрын
@@davidnull5590 Your not the only one that has some rare knowledge of parts and tools attributed to JIS , If you would of kept reading some comments you would of saw where I also talked about that not being a PH1 , but a PZ1 . I bought some PZ drivers specifically for my Old Celica GT back in the day and now use them on my pops Tundra and my Tacoma. You can tell right away that they mate way better than the PH American driver.
@stevenbauer7744
@stevenbauer7744 4 жыл бұрын
@@lane4574 I first learned about JIS screws when I bought my first 240z back in the 80's and had a challenge getting off the screws holding down the carburetor domes.
@markziegler580
@markziegler580 3 жыл бұрын
My 2007 FJ is throwing CEL code P0430. It seems to happen when I city drive in "D" but not if I drive in "4". I wonder if it is RPM related, as "D" never gets over 1500rpm. I replaced my downstream 02 sensor, but that code still appears. I cleaned my MAF which was very dirty. It is still throw P0430 code. I have 170K miles so the cats can not be bad..... Any ideas....
@pedrofernandez8729
@pedrofernandez8729 4 жыл бұрын
When did Toyota begin using MAF sensors in their cars? My 98 Corolla did not come with one.
@lane4574
@lane4574 4 жыл бұрын
Right after that....Some did , it was at the door.
@sugarytv
@sugarytv Ай бұрын
did you disconnect the battery before doing this?
@abdulmunap1797
@abdulmunap1797 3 жыл бұрын
Please help how to remove the connector when the tab or pin is broken?
@airup1275
@airup1275 2 жыл бұрын
Does the batter need to be unplugged to do this?
@kentbernard4319
@kentbernard4319 3 жыл бұрын
does the spray affect the rubber gasket as other videos tell us ?????????
@barryg4452
@barryg4452 4 жыл бұрын
Excellent video. Very informative. Would be perfect if it not for that yellow rag that looks like it came from a wild animal.
@zeepak1090
@zeepak1090 2 жыл бұрын
you used half bottel is too much to clean maf sensor
@NaturallyNerdeeNicol
@NaturallyNerdeeNicol 3 жыл бұрын
What was the customer's complaint or symptoms that led to this?
@bilsob1
@bilsob1 4 жыл бұрын
Hello do you ever do maintenance work on Honda cars, Thanks
@keithlikis9502
@keithlikis9502 2 жыл бұрын
Thank you, that was very informational. I am about to change my air filter on my 2012 rav4 so I will also do this cleaning a well.
@happycat0411
@happycat0411 Жыл бұрын
Sometimes it's better to just buy a new MAF sensor. For my 2002 Rav4 it was only $32 here in Canada (off Amazon).
@karkule5919
@karkule5919 4 жыл бұрын
Procedure for throttle body clean please.
@17EZQ
@17EZQ 4 жыл бұрын
I stripped the screws on my honda crv, any recommendations how to remove them or what to use?
@BabyGangsterIsMe
@BabyGangsterIsMe 3 жыл бұрын
buy another crews at honda parts...or auto zone..they do have it
@alvaropizarro
@alvaropizarro 2 жыл бұрын
Thank you for this!! YOU ARE AWESOME!!!
@frdwd6
@frdwd6 4 жыл бұрын
Don’t you have to disconnect the battery ?
@ccadama
@ccadama 4 жыл бұрын
@Evan Wood. No, you don't have to disconnect the battery. Just have the ignition off and the car not running. Hope that helps.
@3006jmk
@3006jmk 4 жыл бұрын
Good video! It helped me clean mine.
@vvogt4252
@vvogt4252 4 жыл бұрын
Great Video, Very well done! Thanks for telling us how to do this easy maintenance job. Have a Great Day!
@RR-ev3po
@RR-ev3po 9 ай бұрын
2 -3 sprays are enough. Half the bottle is total waste
@robertjeffery6100
@robertjeffery6100 2 жыл бұрын
Great videos thank you
@heftyjay1
@heftyjay1 3 жыл бұрын
Great stuff thank you sir
@eiderdebrito
@eiderdebrito 2 жыл бұрын
Excellent. Thanks.
@drbourihanefarouq
@drbourihanefarouq 2 жыл бұрын
thank you sir, this is resolve of p0107 erreur code.
@carebearboo4247
@carebearboo4247 2 жыл бұрын
Did it take away that code for you? My 04 Rav is throwing the p0171 code and is making the check engine, traction and VSC light go off
@janicethomas3775
@janicethomas3775 Жыл бұрын
Cleaning the MAF sensor still fails. The 2007 RAV 4 is still failing even with a new sensor. It seems when the weather is hot here the car will not run. Then we let it stop for about an hour and clean it again. Then the car will run again then again.. HELP PLEASE.
@gsunde
@gsunde 2 жыл бұрын
Great job A+
@randymurray934
@randymurray934 4 жыл бұрын
Thanks!
@ramtek2702
@ramtek2702 4 жыл бұрын
I've watched several of your videos. You have good intentions but you always seem to omit something important. This time you missed an opportunity to clean the electrical contacts with an appropriate cleaner and them to pack the connector with dielectric grease. Simple but important.
@tspedersen6
@tspedersen6 4 жыл бұрын
Can carb cleaner be substituted for MAF cleaner?
@janoss-zk5fk
@janoss-zk5fk 4 жыл бұрын
No
@ccadama
@ccadama 4 жыл бұрын
MAF sensor cleaner is similar to electrical contact cleaner. Another You Tube auto repair person says if you have MAF sensor cleaner, you can use it for cleaning electrical contacts. Alcohol we buy in a pharmacy dept always has some water. MAF cleaner has no water and therefore will dry faster.
@johnhefter3815
@johnhefter3815 6 ай бұрын
This is the second video I have seen and in both the sensor was clean on one side and dirty on the other side. Hmmm?
@waynejjack621
@waynejjack621 2 жыл бұрын
The dealership are theifs trying to sale me a air filter for 6obucks got the same one for 30 bucks their high as hell then the sale u vehicles high as hell too double the shaft
@on-site4094
@on-site4094 4 жыл бұрын
👍🇨🇦
@raylegend808
@raylegend808 4 жыл бұрын
Hi there no1😎💯👍
@lamantino5
@lamantino5 Жыл бұрын
Thanks 👍🏻
Should You Clean Your MAF Sensor and How to Test It and Clean It on Toyotas
16:21
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
2006-2012 Rav4: Throttle Body,  Intake, MAF, & Injector Service
5:19
Throttle Body & Mass Airflow Sensor Cleaning Toyota Highlander
8:58
Should you clean your Throttle Body and How to clean it on Toyotas
18:07
The Car Care Nut
Рет қаралды 1,6 МЛН
Make Your Car Run Better with a Little Spray Cleaner
3:11
Scotty Kilmer
Рет қаралды 2,3 МЛН
How To Clean a Mass Airflow Sensor (In-depth, detailed version)
10:51
How to clean an engine bay in minutes
7:28
Epic Automotive Detailing
Рет қаралды 14 М.
Mass Air Flow MAF Sensor Cleaning - Regain Lost Power
4:46
Team Oil Drop
Рет қаралды 6 М.