This motor is from bagless Volta ErgoEasy vacuum cleaner. Result of poor filter maintenance motor has dust/hair in it.
Пікірлер: 110
@dimitardobrev32964 жыл бұрын
This is EXACTLY what i was looking for. This is the same motor housing type as in the ELECTROLUX VACUUM CLEANER MODEL : ZSH720 . Hoping this will help future people looking for how to service this motor.
@markharmon49636 жыл бұрын
Thank you. Your video gave me the confidence to fix the inbalance of my filthy turbine.
@sevendyseven40903 жыл бұрын
To anyone watching this video, DO NOT use super glue !! USE Silicon in 1-2inch sections around the round dish part, let dry for a day...now you can cut through it next time around.
@susmitsingh2 жыл бұрын
I know my heart was like nooo why super glue. Now good luck to the next person or even the same person try to repair it next time lol
@mobsterslim8 ай бұрын
@@susmitsinghits a fire hasard its not servicing lol superglue is flammable
@billtucker94555 жыл бұрын
I have made a puller that pops open the cover Everytime. Thanks for the insight.
@gills.manjit63065 жыл бұрын
A tip I used for cleaning dog hair stuck on the vents at min 2.59, I used a small blow-torch to burn off the stuck hair in the vents. WALLA :)
@JJRClassic885 жыл бұрын
Very informative video! Thank you for this. I have one recommendation though. At the end of the video when you pressed the lid back on and glued it; What you should have done was submerged the lid in a bowl of water, microwaved it until the water reach boiling temperature, and then press the lid back on while the lid was still hot. That way, the lid would shrink fit back onto the motor properly, and you wouldn't have needed to use the glue.
@LalSingh-lf4wt3 жыл бұрын
My comments are on JJRClassics88: Your suggestion would work for shrunk fit tolerance. May not work in this case, because the lid was easily put on. At the time of removing the lid, it seems to be expanded by sharp screw driver. The removal process of lid is skipped in the video. It is a difficult step.
@DIY-Bri4 ай бұрын
Thank you. I was trying to figure out how to remove the fan cover. You solved it. Thank you again. Cheers!😀
@BengtEnglund4 жыл бұрын
Beware of LEFT hand threaded nuts at some motor models. It seems that the motor on this video has a right hand threaded nut. For example, the VCM-K30HU has a LH threaded M6.
@RaspyOB1742 жыл бұрын
Thanks for the impeller disassembly video. Now I just need to figure out how to remove my motor impeller
@ingeborgsvensson48965 жыл бұрын
Nice video. My motor also had a lot of cat hair in it but now it is working perfect again. Thank you!
@MicSokol4 жыл бұрын
Don't insert screwdriver into aluminum fan to hold it when trying to remove the bolt. You can damage it/bend the blades and it will make a lot of noise and cause the motor to overheat. There are other methods. I learned this the hardway.
@bentanglangit49244 жыл бұрын
You are right. I am using srew driver in the middle, while opening the baud to the left in the midle
@inderjitwassi14202 жыл бұрын
You say there are other methods - please advise what these are. Thanks
@MicSokol2 жыл бұрын
@@inderjitwassi1420 You take two thin scraps of wood that fit into brush end of the motor, measure the rotor brush size, clap these two pieces of wood and drill a hole the same size as the brush, attach these two wood pieces to the rotor/ brush area/clamp so that when you want to unsrcrew the bolt rotor does not spin.
@Z-Ack11 ай бұрын
So youd rather damage the commutator on the motor rather than put a small dent in the impeller,, just hush.., youre not the genius your momma tells you that u are.. they say that cuz they love ya.. lol. Sorry. Sounded funnier in my head and less like a dick..
@vacuumtests92257 жыл бұрын
I will assemble vacuum later today. All vacuum body parts are washed now. I really hope it works.
@JoeCamarillo7 жыл бұрын
Thanks for sharing! I'll try opening up the turbine in hopes of fixing my own:)
@vacuumtests92257 жыл бұрын
Nice!
@michaelheery74275 жыл бұрын
Getting the motor tefitted is problem
@msazak7 жыл бұрын
I wish you could show ho2 you took that cap off. I don't know how I'll take the cap of the motor off (the part that you explained at 00:40)
@stjepan1010107 жыл бұрын
Thanks for the video! I have problem with my vacuum cleaner motor, that part you took out at 2:43 (UFO shaped) is broken, do you know if it is possible to buy that part anywhere? Or do you know what is it called?
@moisesluiz67702 жыл бұрын
Parabéns muito bom este vídeo está limpeza do espirado de pó valeu são Paulo
@msrnono6 жыл бұрын
Hello. I am looking for a new nut (which maintains the turbine) because I damaged the original one... Could you confirm that it is a m8 with a pitch of 1.25 and with a left handed thread? Thanks
@funlovins3 жыл бұрын
Thanks for sharing. I love the accent btw.
@vinaymulukutla3583 жыл бұрын
He's from Finland.
@family72894 жыл бұрын
So useful am designing my own
@AEON.7 жыл бұрын
Nice socket wrench screwdriver style! Where did you find that at?
@Karolthas2 жыл бұрын
2:15 It's actually better to put the screwdriver between the wings in the inner hole. That produces less force on the metal wings, and bending them won't result in squeak.
@TheRattleSnake3145 Жыл бұрын
Outer hole increases leverage/lowers force.
@fanofradiooxigeniopressaos92487 жыл бұрын
But in this way how is the secret to vacuum cleaners consumes low energy like a EU european energy label and conservates more good suction in the low wattage ones in september 2014 what is the motor is the motor has nano ferrite or is a copper wire and iron? or is something special in the motor thanks
@radioorbitaldavidorbital83977 жыл бұрын
Vacuum cleaner motors about 2200 watts of power that i have one from hoover i run without a fan turbine at 220 volts and electric motor consumes about 170 watts or 220 watts when run with turbine fan they consumes 1500 watts or 2000w because of centrifugation airflow resistance what do you think?
@bauyrzhankokanov54987 жыл бұрын
Not really got your point. I think the only way to increase the efficiency and reduce the power losses you need capacitors installed, means you need an electronic control board installed over the circuit
@TanmayAgarwalJaipur3 жыл бұрын
Hi, thanks for your excellent video! I want to ask one problem I am facing with my Vacuum cleaner. One day the zip of the dust bag was open and I used the vacuum cleaner in a dusty area and I immediately smelled something wrong. So, I switched off the machine immediately. Then after some days in opened and cleaned the motor of the vacuum cleaner and cleaned all dust and debris. There was no smell of coil getting burnt. I dropped few drops of machine oil on both the bearings. After starting, I could see lots of sparks near the bushes and different smell coming from the machine. Kindly, suggest the probable problem and its solution.
@sevendyseven40903 жыл бұрын
Inspect both brushes for to much wear or to deep of a curve in them, if to much inward curve, the side edges may be to sharp causing a kind of outward glancing, dancing arcing..can take out to deep of inward curve with some delicate surgery with a dremel tool to once again match the original brush curve.
@z_polarcat2 жыл бұрын
Thank you for the video, I have a question, when I’m trying to unscrew the main screw the shaft and the rotor keeps rotating with the wrench, how can I hold the rotor from moving?
@abdulrhmanalomireen46263 ай бұрын
You can use an impact driver so it can give torque to the nut not the shaft
@amazingsteelhangclothesbik79604 жыл бұрын
Hi. Sir good day! Question how to reverse ? cycle motor 220 vacuam same Motor like dist video.
@filiplaskovski99937 жыл бұрын
You sound like the guy from the hydraulic press channel!!
@vacuumtests92257 жыл бұрын
That's because guy in the hydraulic press channel is from Finland also.
@billtucker94555 жыл бұрын
You sound like the kid that got his self knocked the 🤩uk out for being shallow minded......
@amazingsteelhangclothesbik79604 жыл бұрын
Thank you!
@augustuscrunch6 жыл бұрын
Nice video.
@Grahams-Grass5 жыл бұрын
I'm surprised you didn't take the opportunity to apply a little lube to the bearings 🤷♂️🤷♂️🤷♂️
@ederaquino265 жыл бұрын
How did you open it?
@bentanglangit49244 жыл бұрын
This is what i am looking for. Excellent...! But you don't show me how to put cap off. And why should you apply glue just like you wont open it again? Thanks alot anyway
@josegower94124 жыл бұрын
La tuerca que quitas he visto videos que para sacarla hay que girarla en sentido horario. Cómo distingo hacia qué lado debo girar para quitarla?
@fjwiyfjzkwlohhdhwkl6 жыл бұрын
Kiitokset ohjeista, nyt on imuri huollettu!
@manzoorawan88555 жыл бұрын
Genius !!!
@PopleBackyardFarm3 жыл бұрын
this was helpful
@perpetuant54524 жыл бұрын
What would happen if I use a metal clamp/tie like those Hose clamps instead of gluing it?
@vacuumtests92254 жыл бұрын
It might work :)
@Electro3Strike4 жыл бұрын
How to disassemble or dismantle
@ashkanmahdyeh12944 жыл бұрын
موتور رو داغون کردی🤗🤗
@m.-4505 Жыл бұрын
I don't remember what is the correct side of the motor who makes contacts with the metal part of the pcb. Blue or red?
@vacuumtests9225 Жыл бұрын
I really don't remember, but it should not matter.
@mc-ec3bu5 жыл бұрын
One way job after the glue i hope you don't need to clean it out again.
@thisfeatureisbad3 жыл бұрын
Unless the vacuum cleaners pre-motor filter fails.
@sherwansherwan50224 жыл бұрын
Thinkyou
@LucianoPiana8 ай бұрын
I need to replace the beige plastic part that is broken. Do you know where and what I search (the name)?
@vacuumtests92258 ай бұрын
You can't buy it separately. You have to buy new motor. These are very cheap motors.
@LucianoPiana8 ай бұрын
I saw prices, unfortunatelly in my country motors cost 50~60 €. I try to fix it. If I can't, I will buy a new cleaner. Thank you@@vacuumtests9225
@Xclub40X5 жыл бұрын
need a vacuum cleaner to fix a vacuum cleaner ita like needing a hammer to make a hammer. . . . only dirtier and worse
@IT-wv1ey3 жыл бұрын
Yahi tha jo main doondh raha tha👍
@2009danial4 жыл бұрын
When you were taking that bolt out you could of used a cloth to not hurt your self when your holding the motor
@inderjitwassi14202 жыл бұрын
If you clean the motor with another vacuum as you did, will it not spoil that vacuum's motor?
@vacuumtests92252 жыл бұрын
It won't spoil it. It's actually very good way to clean it :)
@inderjitwassi14202 жыл бұрын
@@vacuumtests9225 thanks but I meant won't it spoil the motor of the other vacuum you use to clean the motor. For example my motor is full of plaster dust. If I use another vacuum to clean that then it will also become full of plaster dust.
@vacuumtests92252 жыл бұрын
@@inderjitwassi1420 If your motor what you are cleaning is full of plaster dust it shouldn't be too much for your vacuum to handle. Problem comes when you suck up a lot of plaster dust. Bagged vacuums with fabrig bag handle it well, but bagless vacuums really don't like plaster dust.
@ronyerke92507 жыл бұрын
I'm not impressed with your wedging technique to remove and install the nut on the end of the shaft. Bends in the turbine will unbalance it and shorten the life of the motor bearings. I think an investment in a small impact driver will help you not damage your customer's property. Save the wedging for more robust machines like lawnmowers. I personally use a c-clamp on the side of mower decks, by the way.
@kornelijekovac97935 жыл бұрын
The problem is the other side of the axle cannot be fixed. If it only had a slot for a flat screwdriver or whatever, it would be a different story.
@nombreapellido9038 Жыл бұрын
It takes a vacuum to clean a vacuum. Oh the irony.
@marijanavojak38574 жыл бұрын
😁😁😁😁
@marisahorton19766 жыл бұрын
Why is a freak did they have to use AC DC motors kin to use big ones that doesn't have to use stupid electromagnets
@forwhatitsworth3643 жыл бұрын
Are you Hungarian.
@vacuumtests92253 жыл бұрын
Finnish
@forwhatitsworth3643 жыл бұрын
@@vacuumtests9225 very similar accent.
@Z-Ack11 ай бұрын
How to clean a vacuum cleaner. With another vacuum cleaner.. genius! Shit. Now i gotta go buy another vacuum cleaner which is what i was trying not to do by cleaning the one vacuum.. is where they get ya.
@vacuumtests922511 ай бұрын
You can buy spray bottle of compressed air and blow it clean.
@mehmetedex7 жыл бұрын
are you Finnish :D
@vacuumtests92257 жыл бұрын
Mehmet Filiz Yep :)
@mehmetedex7 жыл бұрын
Perkele! Suomi ihmiset ovat hämmästyttäviä
@vacuumtests92257 жыл бұрын
Mehmet Filiz Yep :D
@michaeljuliano88394 жыл бұрын
I’ll bet you’re Finnish.
@vacuumtests92254 жыл бұрын
Oh yes I am.
@michaeljuliano88394 жыл бұрын
@@vacuumtests9225 Your accent sounds like ISMO's.
@vacuumtests92254 жыл бұрын
@@michaeljuliano8839 Ismo Leikola oh yes funny guy :)
@armosa5 жыл бұрын
Kimi pls go back to racing F1 cars.
@vacuumtests92255 жыл бұрын
All right then 😁
@ali-sl9zd4 жыл бұрын
hello my friend may i have your Email? it is important.thaks
@alf3071 Жыл бұрын
it's a stupid design because the dirty air goes through the motor and if it starts to smell you can't clean it inside, the cooling airflow should be separate
@vacuumtests9225 Жыл бұрын
Every modern vacuum cleaner has this style motor. Filters or bag is before the motor so these only get dirty if abused like this unit.
@poiuytrewqoiyujyrter7 жыл бұрын
USE NUT LOCKING GLUE!!!!!!
@camrenzukowski58275 жыл бұрын
Pawel no because then u couldn't clean the motor when it gets dirty
@Xclub40X5 жыл бұрын
6:09 . you want a bit scrubbing action??. . use my ex girlfriend for that. . . she was a rayte scrubber. . and shes available too
@alessandrolabruzzo99686 жыл бұрын
H
@TimTim-ox8dj7 жыл бұрын
This poorly ineficiet vacuum motors is na piece of hit consumes much energy for wasting the old vacuums consumes 1000 or 1100w maximum and conservates good suction
@vacuumtests92257 жыл бұрын
Yes I know. This is also VERY noisy motor.
@alexjogyerek21205 жыл бұрын
Dude are you a butcher ?
@vacuumtests92255 жыл бұрын
Maybe :D
@recycleman9753 жыл бұрын
it looks like a brakepad
@johnathanrice35692 жыл бұрын
Brake rotors are designed with slots to blow air on the breaks when they spin just like this