In Today's video I will show you how to hookup 2 alarm powered sensor to 1 alarm wire. This will work on any alarm system. Please don't forget to Subscribe, Thank you! VPN Special Surfshark: get.surfshark....
Пікірлер: 18
@CJ-vg4tg7 ай бұрын
Brilliant! I'm having a new panel fitted tomorrow (self install). old one being removed by a company. I have 2 exterior sensors with 1 cable going to both in series. Think they used the atz function due to not having enough zones. Not 100% sure. I have more zones now. So this is how I would wire up 2 takex MS series in the same way? Where would I put the eol resistors here? Thank you
@JasonTech7 ай бұрын
You can, use the tamper as the jumper. So you can put the com wire on one of the tampers and put the resistor on the com and the other tamper.
@angelinaorio8 ай бұрын
Hi Thanks for the video. In this case, I can’t use registor? My alarm panel still open because i think i didn’t use registor. Is it right?
@JasonTech8 ай бұрын
Do you mean resistors? Most panel have the end of line resistors turned on by default. So yes, you need the resistor.
@khalidsul232 ай бұрын
Thanks for the video. Is it possible to program the pgm arm/disarm function to also have a panic if it is held. I.e. 3rd party remote button press arm/disarm and remote button hold to trigger panic
@JasonTech2 ай бұрын
You can but there's more to that. What system do you have?
@khalidsul232 ай бұрын
@@JasonTech I've got a Paradox SP6000 alarm system with a Centurion Nova Multichannel receiver
@milandjordjevic87329 ай бұрын
if I put yellow on the com panel, would the sensors work on 1 zone
@JasonTech9 ай бұрын
No, you need the wire in zone 1. Com is just a ground.
@joshf.2855 ай бұрын
Great video. I would like to take a place where I previously had a window with a window contact and reuse the wire for a glass sensor. The problem is the glass sensor needs 4 wires and the window contact only had 2 wires. Can I jump the 2 to create 4?
@JasonTech5 ай бұрын
Your window contact wire doesn't have 4 wires? Because it should
@joshf.2855 ай бұрын
@@JasonTech I double checked and it only has two. Based on that, I am guess I can't do it because I need power and ones to the zone (I assume).
@JasonTech5 ай бұрын
That's right, it won't work. But check your alarm panel, it's got to be a 4 wire. I think you have this type of contact. m.media-amazon.com/images/I/51YAsF8vb4L._AC_SL1000_.jpg
@joshf.2855 ай бұрын
@@JasonTech Thank you. There is only a black and a red. I truly appreciate all of your advice and your videos are really awesome.
@Mthofi3 ай бұрын
Hi Jason. I have 4 IR beams ( 2 receivers & 2 transmitters) that i need to connect on 1 zone. How do i do that, cause when i connect the 2 NC & 2 Common to the one fron the panel, it doesnt work.
@JasonTech3 ай бұрын
You can't do that, you have to connect it in series. See this photo. cdn.getawaycouple.com/wp-content/uploads/2022/01/31093839/Series-VS-Parallel-1024x576.jpeg
@burgalarmguy14 күн бұрын
Confused why he tied loop common to ground? Totally unnecessary. Just tie yellow from motion to common, otherwise this would cause a ground fault on a Bosch panel.