How To: Connect a Main Runner to Another Main Runner From a Different Manufacturer

In our video, we demonstrate how to connect main runners from different suspended ceiling manufacturers using a splicing technique.
This method is perfect for fitters who struggle to identify the existing suspended ceiling grid system and want to avoid the hassle of taking the whole ceiling grid down.
#ceilinginstallation #suspendedceiling

[@AndreGomes-pv9gf]

Thanks bro.. you just save my life!

[@barbrathompson9798]

Was so worried about finger being cut, had to watch twice 😂

[@miltonmartinez6811]

Amaizing It was super helpful I just learned from this video Thank you!!!

[@tamho8383]

Thank you for this Video...It helped me on this a lot.

[@guywhosfly]

Great ending!

[@jmasca05masca92]

Thanks for the video helped me out perfect!!!👍🏻

[@ljml1982]

I just like to cut the main halfway between the slots then slide the new main tab in the same way you made yours but use the factory tab instead.

[@CeilingTilesUKShurdington]

Another way of doing it, great tip!

[@ronwatkins754]

Thanks very helpful

[@erickfunez7650]

excelent i have been looking for this

[@Rehan_bhai-tech_662]

Excellent ❤

[@demmarcsxr]

You should link part 2 to this.

[@davidvoung736]

kzbin.info/www/bejne/lYS1hoNnhb2sqKs

[@tdub8440]

Pretty Kool thats one way of doing it . But still there's 2 easier ways to do it as well

[@WaseemSaddam-z4l]

Thanku sir

[@matthewwindisch9449]

Thank You, helped me out big time!

[@niles006]

One is Armstrong and the USG

[@mohammednadeemqatar3344]

Thanks

[@techgarden5670]

Thank u🤗

[@kiranmeda1188]

nice sir

[@dannyatchley5193]

Please don’t field splice likes this. Now you have a slot right at the joint. Measure back 3 inches from slot use a pocket square mark it, cut it. open the inside up feed new main into cut one. Then you have 6” increments. Squeeze it back together, punch a hole and put pop rivet in it.

[@dannyatchley5193]

Also just throwing up a different type of main your existing tees may not snap in the slot properly. And will have to use tees from other manufacturer. Just use same type of grid if you can and splice it right

[@petermatragrano8271]

DUDE ONLY CUT 1 OF THE MAINS MEASURE BACK 3 INCHES FROM SLOT CUT IT ////THEN OPEN IT UP AND THEN PUT THE OTHER MAIN WITH THE TAP INTO IT THERES YOUR 6 INCHES

[@htema16]

Why would you do that if you already have the link tabs?

[@CeilingTilesUKShurdington]

Hi there, This video is to show how to connect main runners from 2 different manufacturers so the tabs would be different and therefore would not clip into each other.

[@htema16]

@@CeilingTilesUKShurdington thanks for the explanation. I did not notice the main runners were different from each other.

[@jimc9253]

Notice the holes? They’re different, so that probably won’t be the only thing you’ll have to hack in there

[@romancaldera6014]

Nope you cut one at three inches from the slot than plug in the other main and pop it

[@CeilingTilesUKShurdington]

Thanks for your tip Roman, there's definitely more than 1 way of doing this - maybe we need to do a video with your version too!

[@Maltmeister1]

Definitely incorrect,center between the slots,once the tab is created separate the tab and cut one side off so its easy to rivet together once you've opened up other cut main.

[@acousticalinstructorrubenl9957]

But why? Too much cutting. Measure 3" from slot, stab it into the other main runner, Bing Bang Boom.

[@blairgeorge7876]

If the center's for the tee bars are out afew mil it will stand out like dogs balls

[@Forexindustry]

I have 6 years experience

[@itscalledfreedomofspeech5019]

Are you scared to cut with your snips or something?

[@dinoceranic]

This is not how you do it but anyways