How to connect LED STRIP to speaker(BASS)

Thanks a lot for watching, I hope you liked the video!
Don’t forget to SUBSCRIBE!
MUSIC:
1.Groove It by ZAYFALL / zayfallmusic
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
creativecommons....
Music promoted by Audio Library • Groove It - ZAYFALL (N...
2.Track: Jensation - Delicious [NCS Release]
Music provided by NoCopyrightSounds.
Free Download / Stream: ncs.io/DeliciousYO

[@robertopascasio8570]

Hello Sir, how many led bulbs do i need for this particular project, thank you in advance.

[@georgiodavid]

Can I connect it to every 7.1 channel? So I have separately visible from every sound channel

[@ANTIQUE_FARMING_EQUIPMENT]

HEY EVERYONE DON'T TRY THIS CUZ IT CAN BLOW YOUR AMPLIFIER OR HOME THEATER JUST TAKE A 1K CAPACITOR AND CONNECT IT TO LED STRIP+ THEN CONNECT - WIRE TO LED STRIP AND ANOTHER WIRE (+) TO THE OTHER SIDE OF THE CAPACITOR THEN CONNECT IT TO YOUR SUB WOOFER OR SPEAKER 👍

[@ESydeGaming]

He connected it to his stereo system

[@tristian6865]

1. Ruins your amp because of impedance 2. Only works with highs, unless you have a really powerful amp

[@randomvideosfromtiktok5583]

3:59 music title please?

[@atifprince4355]

It's led 12V bro?? Kindly reply

[@AjayJadhav-tr8iq]

Ap na ky use kiya ha bata sktaho

[@yushirgunpath709]

Do the colors change?

[@hashirabdulrazak5810]

Can we connect light direct speaker

[@VlogswithVikrant]

Bhai kisi bhi hometheatre se kr sktee hai kyaa

[@jaybalbuena5045]

what is that 2 small metal what is it called?

[@ismaelmeza1800]

Eso no afecta el amplificado o puede dañarlo por la carga de tira led

[@gustavopetitpanda]

para mi si

[@BrokenBoygaming_pb26]

Is not working 😥 plz help

[@official-on8qh]

led price ??

[@Diablo-RED]

hi brother what is the positive lead the green? .... the green goes connected with the red of the amplifier?

[@gurmansingh4542]

Can it be done with f n d 550x

[@koningvanongewonekakies7419]

Can you blow the LEDs with too much or would they not blow up??

[@tadyslo1203]

They wont blow up but they will die

[@wesoyrozkurwiacz2126]

Can I do this with my Creative A120 ???

[@obaidullah4044]

Bhai is led strip ma length ka bhe hesab hota ha ya nai Replay plz

[@vaibhavrjn]

Where did you insert the 2 pins

[@RidinChevySolo]

LEDs require a 12v DC source. Your amplifier emits an alternating current or ac. This will effect how the load on the amp is received, and will cause damage to the components. Please stop telling people to do this.

[@tuffgong3248]

Is there a way to do it

[@jatir_bhaii_]

Bro how I set in microlab speakers

[@barrytrowbridge5067]

How meny LED can you have of the speakers

[@scottneulist9495]

Nice, do you know if this works with more powerful amplifiers/speakers. Thinking of hooking them up to my 600w RMS subwoofer in my car

[@leeknivek]

Bigger resistor, you only need a tiny amount of power from the signal and 600w will blow these up. (I think) if you have an amp that does 600w @ 8Ω then it will do 300w @ 16Ω, 150w @ 32Ω, ...... 16w @ 128Ω, 8w @ 256Ω - measure the resistance of your strip and make up the difference in impedance with another resistor inline to bring it up to the correct value. I would check the rating of your amp first, if it is actually 600w at 8Ω or 4Ω or whatever, from there you can extrapolate where you need to get to.

[@Cashendogs]

@@leeknivek it will work I’ve done it to amps that push out 1800 watts 🤙🏽

[@johnlloydcabacungan5717]

Can I go directly to speaker?

[@ANTIQUE_FARMING_EQUIPMENT]

DON'T TRY THIS

[@johnlloydcabacungan5717]

Bro I know it how to work set up I know operator I know

[@ANTIQUE_FARMING_EQUIPMENT]

@@johnlloydcabacungan5717 Get a 1.1k resistor and connect directly to speaker

[@rogertyler3237]

I Have Some Led Strips with 4 Pin Connectors How Do I Know What Wires Are + Or -

[@Ryanwheatley07]

I don't recommend it at all, but black is usually negative, use a battery to be sure

[@TheLordAdder9]

Is the led light connected to the bass or is it separate? Is it safe to cut the led cord or will the bass be cut too?

[@script2351]

Evet bass'a bağlı

[@bikramveersingh6027]

Where to put the wires in the input or output socket???????

[@tharindugihan6383]

This is very good to the amplifier 💥💥💥💥rest in peace

[@locorimax]

right

[@TorbTorb]

10 m led strip have about 24watts so his thing will have 3 watts. so shouldn't impact the performance a lot.

[@RyanProxy995]

Bro, I need some guidance with a project that I am doing, can we get in touch?

[@Speakershocker]

You kill the amplifier!!!

[@marcel7036]

Ja Moin, dich sieht ja man überall😂

[@Speakershocker]

@@marcel7036 Ja normal. Sowas wie hier geht auch nicht. XD

[@marcel7036]

@@Speakershocker ja geht auch nicht, teure Verstärker schalten da schon automatisch ab

[@Speakershocker]

@@marcel7036 bei so einem Unfug aber auch nicht immer.

[@leandroebner1405]

@@Speakershocker kannst du mir erklären warum hier der Verstärker kaputt geht? Kenne mich jetzt nicht wirklich aus aber wer nicht fragt bleibt dumm... Wenn jetzt theoretisch die Gesamtimpedanz über der Minimalimpedanz des Verstärkers liegt (z.B nur die LEDs ohne Boxen) fährt der Verstärker doch auch nicht ins Clipping. Dem is dass doch egal oder? Oder weil der Strom jeweils immer nur ne halbe Periodendauer fließt weil die LEDs während der negativen Amplitude sperren? Was schädigt hier dem Verstärker? Danke

[@entertainmentstation4662]

1: you make it look like more difficult 2: frome amplifier you get less power when it's normal volume, so you have turn volume a lot higher to get enough illumination * putting led directly not gonna helps you * just simply buy two amplifier one for speaker one for led There can be other alternative but At least you don't have to turn higher volume and 100% sure that your amplifier don't blow ✌

[@adamasyudistira180]

Song?

[@linsonlazar3657]

How many led lights can it make glow? Because when i connected a series, it didn't glow. Can you help me with some calculations

[@elektromicha6777]

bro this is fake ;/

[@VC27]

@@elektromicha6777 - Seriously? Do you even know what you are talking about? I did this with a car headlamp bulb when I was 13 on Dad's old Aiwa AF-5090. Lucky that it didn't fry the amp., should have added a resistor. However, it worked! Stuff your mouth with your old socks before you call it fake.

[@monermajhi2218]

Is amplifier ka Kya naam Haii Plzz link dija.....plzzz plzzzzz

[@ramusicnation6908]

Why is it only blue not red and green

[@michelleyoung934]

Can you add led lights to JBL boombox 3

[@harshitseth7239]

Can we use 20 watt led strip tube light on strip (T5 100 led)without driver please reply anyone ASAP

[@as424100]

You know that you actually can cut the shrink tubes shorter depending on how much you need?

[@paulybeatz3688]

I knew it but I don’t do it. Cut is cut

[@as424100]

@@paulybeatz3688 I know man but honestly it drives me crazy when I see someone wasting material like that..

[@mariniluca9197]

Pakai adaptor gk bang

[@cheezboi1.041]

I'm not sure if I want to do that to my speakers

[@Weber1987]

How come you can't just use red and black and directly hook into pos and neg on speaker

[@pragavirtual]

well im not very knowledge in eletronics but i know some, so there is a way to kill your amp by doing this, using AC (speaker works with Alternate Current, leds are designed to work with DC) with leds, youre forcing voltage into led in a way they are not meant to have, doing that any led in the strip may fail and go into short circuit and then kill your amplifier. Im thinking that theres is some workaround to this, adding some other diodes into the negatives and RGB inputs on the strip, or just using some resistors in the same way to limit the voltage that goes to the leds, dont ask me for schematics bcuz i dont know.

[@ronaksingh7149]

How much wattage the led strip light should be?

[@ronaksingh7149]

I have made a 200w speaker I power it up with 12v 5amp adaptor

[@ronaksingh7149]

I have tried it when I power the speaker it just bumps up and not blink after the music is on

[@ronaksingh7149]

Please let me know about it

[@richard16372]

Is that a normal 12 volt led strip?

[@AVmake]

This is RGB(red ,green,blue)led strip 12V, so I can change colour by connecting different wires, but you can use one colour led strip that's more simple.

[@AliYassinToma]

@@AVmake but what if the sub is in the amp and only tweaters are out of it ...

[@CARMEKANIK]

please dont inform people to do this as it will burn up the amplifier...

[@jblchange3channelandsounds284]

lol?

[@marcel7036]

Yeah, TexasXplorer youre right

[@paczkos545]

it did not burn the amplifier

[@timnerenberg]

@@paczkos545 not immediately but it will

[@moocrafter972]

Why? Pls show me i dont understand

[@badshah3002]

Buy Yeelight Strip light this feature is also available in that strip

[@SantoshG360]

Please give links

[@Ryanwheatley07]

Yall, i only recommend if you take abart old bt speakers and use em for diy bs systems, I use leds with it straith connected, but if you have an expencive system that you def dont wanna replace, dont do it by anymeans, i actk as a short circut and will blow the sound chip real quick

[@tadyslo1203]

Yes all cool and that but if u have a radio that outputs more than led's are rated for they are going to frie.

[@harddrive7316]

The title should be: How to blow up your amplifier

[@alexandruargint1937]

Yap :))

[@vee9260]

How....

[@RiccardoRivi]

@@mathwins7953 so if i have a 1973 Pioneer amplifier does it work?

[@isaacsanchez7317]

Why?? Could you please explain me?

[@immensiverocker4813]

Exactly because I tried it and I blowed my amplifier too... Please don't try this

[@FireInFairy]

Unmm, I don't know about that one. The speakers run on AC voltage and LEDs work on DC so it would not work. But I think your led strips are AC voltage because you are not showing or writing it.

[@shadowdrimex5226]

Hi Hifi, it was the same and the ohm is adjusted to the speaker, performance when recording and transmitting, it's no use putting up a series of LEDs equipped with resistors, an LED works at about 3v, so you not only damage the hifi, but it can also cause a short circuit because there is no switch on it!

[@dinasaputri4050]

Buwat apil besar bisa a om

[@TenzinWood]

0:05 SONG NAME?

[@mantasbudrys9941]

It will burn your amplifier and btw there is Sony speakers with pre installed LED

[@momory1999]

hey, i just find your channel in my recommendation and we have almost the same "name", i tough it was funny ^^! nice content by the way

[@AVmake]

Hahaha that is funny, thanks!

[@KHKIEGAMINGSHREE]

kzbin.info/www/bejne/oHKlemOrgNmjgac

[@spyboyAchin]

Vai led strip kitna volt ke hai

[@KHKIEGAMINGSHREE]

kzbin.info/www/bejne/oHKlemOrgNmjgac

[@twowheeldrivetwd885]

This kills the amplifier

[@gameboy1984]

How?

[@davidluptak]

@@gameboy1984 Drains too much current from it to light up leds

[@Kanoshe]

@@davidluptak go on

[@davidluptak]

@@Kanoshe Amplifier is for speakers with definitive ohms and if you add another appliance like leds than mosfets or chip may burn up from excess current

[@Tesdraline]

@@davidluptak 4 ohm speaker is a much bigger load than those few LEDs

[@atsstockburn]

I've never seen so many "no-no's" in a how to video. I won't even go into it. Everyone has to learn somewhere. lol.

[@TheCrystals5]

How to blow up the led strings

[@bersa2934]

Hola buen dia yo tengo esa luz led pero el mio tiene dos cables se hace lo mismo ?

[@edwindanielramirezlopez5490]

Si le das más volumen no se queman decasulidad

[@RobertoalejandroDiaz-q1r]

Holaa yo lo hago asi como muestra el video lo ise y no prende las luces xq seria q no prende

[@witastalker8348]

its not working plz help

[@leandroebner1405]

Wheres the problem

[@zner4539]

What are material you used:

[@petsplanets2369]

4 cable??? Please explain this i dnt knw

[@filipstevanovic9422]

Why RGB? U can use blue led tape????

[@AVmake]

Ovo sam imao,pa eto da iskoristim...

[@filipstevanovic9422]

@@AVmake haha ja ne mogu da verujem, zaista nisam očekivao da srpski pričaš Jako prijatno si me iznenadio. Ps jako mi se sviđa ovo što si napravio :-)

[@filipstevanovic9422]

@@AVmake Sviđa mi se tvoj kanal! Evo subscribe :)

[@AVmake]

Pozdrav!Zapravo sam iz Hrvatske,vidio sam ti ime pa mi je lakse bilo odgovorit na hr hahah

[@SANBOOST]

song at 4:03

[@NVMUSICTV]

By doing so you are reducing the power inputed to the sub

[@jomann3213]

What? You know this is a 3 way speaker yeah? So all 3 drivers would be affected not only the woofer (or sub as you call it even tho it's not). You are mostly just burning out the amp.

[@SalComposer]

@@jomann3213 you can have a woofer with only medium and hight frequencies on it... what are you talking about? sub is a professional term to define lower frequencies under 60Hz that is even the frequency that electric current flows, besides, that kid also named the video about BASS , and no... not all frequencies are afected the same simply because the amp sends much more power from the crossover to deliver in the speacker the low and sub frequencies, than for the highs frequencies. If you use old lamps, you will see that they dont move much with the highs of music almost nothin but do a lot with kick drums and sub bass. for you to hear from a speaker tweter 15000Hz you need 300 times less energy from the amp, than the energy you need, to hear a Kick sub on theyre usual 50Hz frequencie.

[@cirilogomes7477]

congratulations, you work is very beautiful. parabens, seu trabalhor ficou muito bonito.

[@rogertyler3237]

Hitlights Told Me The Led Strips Won't Work Just Connected To Speakers. They Said They Need A Content Steady Flow Of 12 Volts.

[@sauravraj5130]

Ham Yaha light parichit karna chahte hain kahan milega

[@davidedgardodiazchavez9116]

Bro tengo el mismo aparato solo que de tres bocinas pero me da miedo conectarlas así nomás que posibilidades hay q no se me desconponga en equipo de sonido

[@leoye7814]

Actually u can just go buy rgb led strips with mucis mode

[@tushargupta9024]

Cost bro 🤧

[@OpsterGamingYoutube]

This is like the kind of thing that i would love to do but i just know that i will never bother learning because of the danger of fire lol. I wouldn't trust myself to not mess it up xd

[@ConstabeastYT]

I am 12 but....same 🤣

[@CH-FOUR]

@@ConstabeastYT i am 13 and i do this things for 5 years now

[@CH-FOUR]

@Teodor Vranchev i like mostly computers and speakers

[@why_ju_st_why]

@@CH-FOUR same

[@madhukeshnp]

Use a transistor to switch the led strip and connect the base pin of the transistor to the amp like you did not...

[@perrypebriant506]

Nice I get inspired

[@Thesaint2k13]

Nice job , pretty sure the amp can deal with the extra 12v power draw , lol people in comments make me laugh it's not like he's going to have it on 24/7 with speakers at 100% lol it will be fine worst case scenario you have a power surge and pop an led , lol

[@sumeshmullassery5585]

Circuit diagram plz

[@erlendh3257]

Really? If u dont see how this is done you probably shouldnt tinker with electronics

[@CarlosRodriguez-vd7bs]

Que se utiliza para hacer eso

[@parshuramjadhav2467]

Loved this video because no difficult tasks is there...

[@Retro719]

Remember the Radio Shack light organ boxes, where each of the 3 colors operated on the different sound levels? That's what I want to learn how to properly make.

[@VladyslavShchelkov]

all genius things are very easy

[@euvo_sound]

i also made this one but the amplifier never blew up.

[@mirja4838]

How to LED light fitting in boat soundbar please provid please please please please please please please please please please please please

[@maximanvip1999]

4:09 sound tittel?

[@alexandrualex2066]

Have you found it?

[@maximanvip1999]

@@alexandrualex2066 no

[@alexandrualex2066]

If you do let me know

[@TorbTorb]

a little late but darude sandstorm

[@reydavidchicuate3366]

a mi no me funciona

[@martinhorvath259]

3:15 wats the songs name? Plzz

[@ormel5155]

Mortals warriyo feat Laura brehm

[@honzahanak524]

Song at 3:57 pls

[@mcpeguyjph35]

Jensation - delicious look it up on youtube and its the one by ncs.

[@duartegomez3547]

esas luces le quitan volumen a los bafles,o aveces si es mucha la potencia en volumen se queman los LED,mejor arriesgarse

[@doctorpetrovich9296]

just buy Cheap ($2.50) LED driver that controls RGB stripe according to music bass line. Connected to 12V it detects music rhythm and flashed LEDs to the music. This creates disco/club-like effect, visualizing BPM of your music.

[@gothangel6221]

are they just callef LED drivers?

[@doctorpetrovich9296]

@@gothangel6221 i think they are called Arduino Uno LED Sequential Control

[@johnnymotors2023]

Braw.... this shit I was doing when I was 12-14 years old... now I am 24.... I thought that u found something better not like this. Something that will light up even you have the volume at 5% or at 50% and will illuminate with the same intensity based on the bass kicks, etc.

[@ladyboss4842]

How?

[@Kanoshe]

yeah apparetnly you gotta have like arduino's and coding to make it proper

[@rafee9442]

​@@Kanoshe you can use a spectrum analyzer board

[@projectmanagement2356]

Somebody got his big boy pants on all by himself 😂

[@JAMBI..]

Yo I've been searching for shit like that. Every tutorial or led light kit seems so basic.

[@technicalrathorevlogs9067]

Sar ak ayse bideo banaiye jo kam voise par l i d kam kare ham kisi song ko chalate he to Boise adha macsimam karna padta he to aysa na ho lid kam Boise par chale

[@OscarRodriguez-qz4iq]

hola ,quiero saber cuanto de volumen soportan las led

[@Joss86-p7x]

No sé queman bro

[@nashtech8548]

Excellent Work ..

[@adamasyudistira180]

Name song 3:20?

[@JA1860_G]

Warriyo - mortals

[@bujanganbujang1555]

Bikin video bos pasang lampu led semua jenis , dri lampu kolong lampu led strip dll pasang ya ke batok lampu sorot viar 200L dan motor matic

[@josecabriales7440]

no ocupa una resistencia o halgo

[@conxtantino]

It was perfect, congratulations

[@flashteam3435]

san nakakabili ng led