Today Anthony shows you 3 ways to easily debadge your vehicle. If you enjoyed this tutorial please hit the like button and subscribe to our channel.
Пікірлер: 163
@johnowens52072 жыл бұрын
A video that shows you 3 ways under 5 minutes. I rate this 5/5! Informative and quick!
@Liberty4Ever Жыл бұрын
Great video. Exactly the information I needed. Wasted none of my time. Thank you!
@savyk34082 жыл бұрын
Thank you! Easy, and right to the point this helped 👍🏽
@tomkopko88562 жыл бұрын
Thanks! Well filmed, no extra commentary, and the results were great!
@premiumgarage2 жыл бұрын
Glad you enjoyed it!
@mwdallas1 Жыл бұрын
@@premiumgarage yes, perfect video. Many thanks!
@l.c.jr.77923 жыл бұрын
Just wanted to say thank you. I used you fishing line method and everything went as good as it did in your video. This was so easy and my WRX rear end looks so much better. (A++++)
@anthonysuriano81283 ай бұрын
What pound test?
@davidheard99539 ай бұрын
Great job man! Killin’ it. Go make that money.
@littleweirdprincess4 жыл бұрын
I have a fourth method: it involves a "helpful" toddler and having your back turned for a second 😭. I just need to get an adhesive remover to make it see like it was on purpose lol
@Your-Mums-Favourite-Son4 ай бұрын
That’s why I’m here!!!😂
@chekkech7574 ай бұрын
Too funny
@BRock864 жыл бұрын
Nice simple video, thanx guys
@idkchocolate4 жыл бұрын
Thanks for this informative video
@whateverprecisely Жыл бұрын
Really great video with simple and quick instructions! However I do have one question, I was able to see some residue just on the edges, would that come off with more glue remover or a normal wash or a power wash or just time?
@davidsimpson68703 ай бұрын
The chemicals used in adhesive remover can cause discoloration and dulling of the paint surface and can also damage the protective clear coat on the car. Also, If you ran the eraser wheel on anything other than low speed and/or stayed in one spot too long you probably burned some of your clear coat.
@craigdgriffiths62064 күн бұрын
There’s always a smart arse.
@BERNARDO7123 жыл бұрын
This was helpful... thank you
@vincentslusser92053 жыл бұрын
Sweet video. Thank you.
@rogergorospe86902 жыл бұрын
Great thumps up,thx for info
@jessejones47302 ай бұрын
Great info. Thanks
@GhostedStories2 жыл бұрын
Thank you for this!
@pinkeye002 жыл бұрын
Just saw the heat gun! Nice!!!
@AndrewLeet922 жыл бұрын
I layer the masking tape on one of the sides of the emblem I'm about to remove. Prying it off will make it dig into the paint on the opposite side, at least in my past experience.
@Tribulation883 жыл бұрын
You might want to polish the surface after, you can still see the outlines on the back when you're finished @ 3:04 . The longer those badges have been on the car, the more obvious it will be without a polish.
@dubstomp498 Жыл бұрын
how do you recommend polishing? I have wax and wash, would that suffice?
@bswayde Жыл бұрын
@@dubstomp498 yes
@jaymanrun1 Жыл бұрын
Light buffing
@marketbuy11 ай бұрын
This video is about removing the emblems, not about polishing the car after removing the badges.
@-Grifter8 ай бұрын
@@marketbuyIt should all be part of it Why find a separate video on how to remove the marks after removing the glue after debadging a car!
@wickedcitywoman Жыл бұрын
Tysm for this!!
@jasonhutchinson8060 Жыл бұрын
I have the X5M competition and want to remove all model/name badges from both interior and exterior. How do you do about removing the X5M Competition badge from a carbon interior center console - without losing the finish on the carbon trim that lies underneath? I would like to remove the badge and keep the nice, consistent finish of that glossy carbon trim. Thanks, J.
@momoneyhabits3 жыл бұрын
I got my car being debadged and a chrome delete wrap right now. Definitely gives the car a cleaner look
@user-yw8yx7fh7t2 жыл бұрын
How much did it cost bro
@ericmarciniak35412 жыл бұрын
@@user-yw8yx7fh7t 15 bucks if you plastidip like i did. blacked out all the chrome around my windows 2 years ago on my g35 and its still looking good.
@hhunting_trolls95002 жыл бұрын
@@ericmarciniak3541 my guy im finna do that next week now 😂 tint both front windows plasti dip chrome trim and lights 🔥🤘 your comment just reassured me why i SHOULD 😂🔥
@Novehx2 жыл бұрын
@@ericmarciniak3541 what do you recommend for chrome grill. diy or buy one online
@Tstone401 Жыл бұрын
you the man bro
@dagorilla51772 жыл бұрын
Dope 👍🏾 Thank you bro!
@averysidilau1455Ай бұрын
Awesome! Now I can put a decepticon logo on my car
@April-201 Жыл бұрын
Damn! Thanks 👍🏾
@MrTmenzoАй бұрын
Thanks 👍
@luciusn214 ай бұрын
How new was this car when you did this? I want to do this to a 2011 but I'm worried the paint under the badge will look different than the surrounding paint due to the age of the paint.
@joedude5757 Жыл бұрын
Yo!!! Much appreciated sub just for this. Will watch more
@osakabay774 Жыл бұрын
Great helps
@marketbuy11 ай бұрын
I own a 2023 Nissan Ariya. I want to black out my Ariya emblem. Should I spray primer on it first before I spray paint it black? Once done, how will I reapply the emblem? Use cement glue over the existing double sided tape?
@lasvegasotis67804 ай бұрын
Awesome
@DarkSkinBae11 ай бұрын
The first methods right in my budget 😂
@Donaldtrummp3 жыл бұрын
People out here putting 3.0t badges on their car & this guy is taking em off 😱😂😭 I love it Ps good video thanks
@presidential32282 жыл бұрын
who tf would do that … thats dumb
@Donaldtrummp2 жыл бұрын
@@presidential3228 idk but people do it you probably not from any large inner city if you never seen it lol
@presidential32282 жыл бұрын
@@Donaldtrummp 😂 gotta be
@trent20612 жыл бұрын
What about the remaining glue? You can still see it after you finish.
@SANTIAGOSANCHEZ-yw3pd Жыл бұрын
Can you remove the adhesive with Goof Off? Thanks for the tips
@haukopkhual11 ай бұрын
first method work for me.
@joshpitcher50036 ай бұрын
Can u use jus regular alcohol to clean the left over residue?
@davidgiles97512 жыл бұрын
If you don't have (or don't want to buy) Goo Gone, I've had good luck using WD40 to remove the left over adhesive. Then clean it with some Mequiar's cleaner wax (or whatever you prefer).
@Colin623 Жыл бұрын
Surgical spirit works great !
@danperez18603 ай бұрын
A mix of dish soap and water will remove any greasyness left by the WD-40.
@MJJCvideo4 ай бұрын
@Premium Garage Cool,may I know if you would like to review our foam cannon S V3.0?☺Thanks in advance!
@Miikecash272 жыл бұрын
What should I use to put back on the emblems I have a few small letters
@huchimo01 Жыл бұрын
Hello. Nice video. I however did use the Rapid Remover and attempted to remove the last of the adhesive. There is still a very very fine layer of the adhesive that I am unable to get off. Basically you can just see the faint outline of the original emblems. How do I get rid of that please? This is on my 2018 Alfa Romeo Stelvio Quadrifoglio. Thanks for the assist.
@michaelatwood2368 Жыл бұрын
A good polish should take care of that
@devilorangel4249 Жыл бұрын
Step 2 seems quick and the easiest
@germanmendez63946 күн бұрын
The heat gun makes it so so easy
@gregnixon129610 ай бұрын
What is the grit of the eraser wheel that you use?
@kevlandy3 ай бұрын
Can I use brake cleaner to remove the adhesive?
@museman0072 жыл бұрын
This guy goes straight to business, no extra talking, no “mansplaining”, he is effective and shows three methods under 5 minutes. Liked, subscribed and five stars.!!!
@markunion9156 Жыл бұрын
Would the eraser tool remove the black marks that have sat around the badging and lettering? I have a white vehicle and dirt around the lettering. Would you guys also know if there's any methods to remove those black outlined around the lettering without using any tools? I removed some sticky residue from badging with goo gone and worked great, and figured maybe the more I keep wiping the outline off with goo gone every once in a while it'll eventually come off.. any other helpful methods? I don't have an outlet or any tools currently at my apt complex..thank you guys and great video, I'll be using these techniques too for any other badging I have.
@JamesHamp93 Жыл бұрын
The longer the vehicle has had the emblems on the harsher the "outline" will be visible as the paint underneath will still be pretty much untouched. I use a touch of meguiars ultimate compound and buff it and it removes like 99.9% of it but on a funny angle in a funny light you can still catch a glimpse of it. You might get some luck using a cheap car polish and working it for a while.
@user-so2ri5vu9h29 күн бұрын
you can still see the marking of where the badges were even after adhesive remover was applied, you need to buff it out.
@smoothhaha232 жыл бұрын
What’s the name of the substance he used to wipe with ?
@tofu86oc552 жыл бұрын
wait, so if you just want to replace a chrome badge with a black badge, just fish line and glue the new emblem over the old glue (without removing the residual glue?)
@presidential32282 жыл бұрын
no take off that old glue use new glue
@Nscap4 жыл бұрын
Post moreeeee
@MikeDraws4 жыл бұрын
can you do a video on re-installing badges after the car is wrapped
@idkchocolate4 жыл бұрын
Agreed
@Pnwliving3392 Жыл бұрын
Can I use paint lacquer?
@Chillphill83 Жыл бұрын
What pound fishing line do you recommend???
@Colin623 Жыл бұрын
Floss works great.
@BRock864 жыл бұрын
What size fishing line do you recommend?
@swingman1414144 жыл бұрын
30lb works fine
@D_Snutz3 жыл бұрын
...depends on the fish you're after...
@arsen62653 жыл бұрын
Floss works
@gilsgarageofficial Жыл бұрын
You can use automotive goo gone as well. Make sure it’s the car one, not the regular goo gone.
@kalani1987 Жыл бұрын
What's the difference between the two?
@gilsgarageofficial Жыл бұрын
@@kalani1987 the normal goo gone has abrasives that can eat the paint
@rgtian19872 жыл бұрын
Just want to know what liquid you use for clean the 3M tape? Thanks.
@Colin623 Жыл бұрын
Surgical spirit works great on any glue residue !
@rgtian1987 Жыл бұрын
@@Colin623 Thx!
@EdwinYRequena8 ай бұрын
So we dont have to use a heat gun at all?
@admiralgoodboy Жыл бұрын
What's that liquid your using called?
@Granolaboy1 Жыл бұрын
What about older cars? I have a 2007, the emblem came of easily, but the glue and outline is stuck. I’ve been using WD40 and tar and bug remover for about an hour and it’s not wanting to come off.
@JamesHamp93 Жыл бұрын
I've had some good results with meguiars ultimate compound, it's not the cheapest but you can use it for other things. It removes like 99.9% of it but in a funny light, on a funny angle you can still catch a slight glimpse. You might have some luck with a cheap car polish or something similar though.
@Granolaboy1 Жыл бұрын
@@JamesHamp93 I ended up using a 1600 grit sandpaper to wet sand as much until as I could before I ran into “oh, sh!t, now I need a new paint job!” That helped, then wet over Meguiar’s compound, the polish, then wax. You can’t tell I sanded some of clear coat, but the outline of “Element SC” is still there…etched in the paint. Like yours, at a certain angle, you can’t see it. Up close, you can’t miss it!
@JamesHamp93 Жыл бұрын
@@Granolaboy1 I read the first half and thought 'oh shit hes gona need a new paint job!' But then you said about the compound and polish and you literally took the words out my mouth haha! What colour is your car by the way? My A5 is like a Daytona grey and the A3 I had before was also grey, slightly lighter in colour. The A3 was a 2006 and that was much more visible in certain lights/angles but on my A5, which is nearly 10 years newer, you can barely see it unless you look for it in but the lighting and angle has to be just right.
@Granolaboy1 Жыл бұрын
@@JamesHamp93 my 07 Honda Element is Nighthawk Black Pearl. Next spring/summer I’m going to brave it and that spot myself…sand it down completely, prime it, spray with Nighthawk Black Pearl spray and clear coat it. The videos make it seem too easy….hey, I can do that! What could go wrong? 🤣Hopefully I don’t f@ck it up! Have you tried using clay bar before compound/polish/wax? Doing all 4 steps is tedious as can be, but the paint looked so beautiful afterwards and felt oh so smooth!
@JamesHamp93 Жыл бұрын
@@Granolaboy1 Ahh nice, that's the same as the Type R black if I'm not mistaken? Oh fair enough. I wouldn't have the balls to do that myself as I have no confidence in painting my own car but if you reckon you could manage it I wish you all the luck in the world. Chris Fix has a video where he completely restores and paints part of his car, with a spray can, and it comes out amazingly well. He gets rid of the orange peel effect by using some 5000 grit sandpaper I think. It looks amazing and he makes it seems super easy but I know i would go wrong somewhere 😂 And when I compounded and polish the entire car I did clay bar it all first and the colour has held up really well tbh. I try to not do it much as it does eat away at the clear coat if you over do it but maybe a full go over every year or 2 with regular washing and waxing keeps it looking good. When I took the badges off the back I didn't clay bar it because it was such a small area in comparison to my bonet/hood for example which is like speedboat long lol!
@broughton90 Жыл бұрын
I think the safest way to do this at home is the fishing line technique I'm seriously considering debadging my audi s1
@RebenzoClark10 ай бұрын
It seems to me that you weren't that serious about debadging it, or else you would have updated us and let us know it was completed. Disappointing
@_swol_swole_bean6 ай бұрын
👍🏼
@yuliyaaleks7922 жыл бұрын
4th method... Floss, razor blades and WD40 🤣 works amazing. I debadged my Audi last weekend. I still have some cuts on my fingers but totally worth it if you're too lazy to go to the store 🙃 😅
@JD1mfC2 жыл бұрын
wd-40 to clean off the adhesive right?
@yuliyaaleks7922 жыл бұрын
@@JD1mfC yes... it takes a little longer but it works
@yousuf_tauq56282 жыл бұрын
I used bug and tar remover it worked better than wd40
@claytonphoenix74572 жыл бұрын
Would nail vanish remover work?
@Colin623 Жыл бұрын
Just use surgical spirit I always have some in the first aid kit, great for removing any type of glue residue, evaporates quickly, and leaves no smell once evaporated.
@joey956613 жыл бұрын
You can still see the where the badge was
@dabussy60013 жыл бұрын
Where
@lukablank26472 жыл бұрын
i'm taking the badges off my 1999 merc and the glue shit will not come off with adhesive remover...
@iLeaveMeanCommentsSometimes2 жыл бұрын
Yeah the older the car, the worst. You might want to try the eraser wheel method. Although you’re taking a risk by scratching the paint. Good luck.
@Colin623 Жыл бұрын
Try surgical spirit !
@ryansheard8092Ай бұрын
Goof Off won't hurt the paint!?
@jdsim91738 ай бұрын
All you need is a heatgun and floss or fishing line.
@yoshima153 жыл бұрын
I can’t lie. I ALWAYS THOUGHT you needed a heat gun!
@museman0072 жыл бұрын
Hot water does the trick also.
@kenna.93682 жыл бұрын
How about a hair dryer?
@Zmay2007 Жыл бұрын
Infiniti Q50
@kayoromani41962 ай бұрын
Just scrape off the 3m w a credit card just be careful that u don’t scratch the paint
@Michaelobama1842 жыл бұрын
I was removing the badges on my Tacoma truck and I turned away for just a second and my toddler was eating my goo gone.
@RD-ox3ce6 ай бұрын
I’ve used dental floss before
@aoclepsidra3 жыл бұрын
what is the name of the thread used to remove it? Thanks
@MonacoVirago3 жыл бұрын
Thread=fishing line
@rossn51863 жыл бұрын
@@MonacoVirago Apparently dental floss also works just as well.
@MonacoVirago3 жыл бұрын
@@rossn5186 yes it does… pretty strong hunh…
@MonacoVirago3 жыл бұрын
@@rossn5186 I used Goo Off and Goo Gone… the Goo off worked better…
@SinLaurent3 жыл бұрын
Any recommended fishing lines?
@bsaccs1963 жыл бұрын
You can use dental floss as an alternative. It's actually better since it's thinner making it easier to cut in between the adhesive and decal. Personally I would not risk damaging the paint buy debadging the car. The process is not as easy as it appears and does require some luck.
@SinLaurent3 жыл бұрын
@@bsaccs196 so dental floss over fishing line?
@bsaccs1962 жыл бұрын
@@SinLaurent Correct.
@sammyg805 Жыл бұрын
I have heat gun but nowhere to plug it into because I live in an apartment
@kalani1987 Жыл бұрын
Extension cord
@apathy113039 ай бұрын
Just used a heat gun and dental floss to debadge my x6
@raulramirez65752 жыл бұрын
5th method add Vicks on the badges Scrape super hard with flat head Your welcome.
@kareemali1742 Жыл бұрын
What is the point of debadging a car
@fnogz1337 Жыл бұрын
More clean look
@coriw85928 ай бұрын
Be different from the rest
@davidblagg257611 ай бұрын
Goo gone sucks and braided fishing line works better than fishing line and dental floss 💯
@NiCccccccccccccccccccccccc Жыл бұрын
or goo gone???
@davidwalia3451 Жыл бұрын
Just 🤣
@firasali41183 ай бұрын
But why, you want to debadge your emblem, 😮
@hswiss3646Ай бұрын
Chrome deletes, aesthetics, resale (scamming), personal preference. I could go on.
@JoeyBaby472 жыл бұрын
Is the masking tape really necessary? It doesn't seem to provide any additional benefit. Also, your outro music was way too loud.
@Tysowavy24 Жыл бұрын
any 3.7’s here?😭
@codymcnary36077 күн бұрын
Why is it that Infiniti owners seem like the only people that like “DEBADGING” their car that people worked so hard to assemble?! I never see Acura, Lexus, BMW, Mercedes, etc.., do this?! Why! You are just lucky this isn’t a “Ferrari”, hence You would be put on their Black List and can not buy another one! Anywho, to each their own! Please just don’t put any “Skyline” stuff on it!
@juz2sxc65110 ай бұрын
Nail polish remover works a treat as well... As a female i alaays have it lying around and when ive done little chio touch ups and maybe got a bit carried away with the paint, id simply use nail polish remover to take it off and start again...
@Violet_Lotus_5 ай бұрын
exactly why do people want to debadge their cars? I thought they wanted to show off the brand? I have a Pontiac Vibe, so I know why I want to do it , 😆
@Hughmun42Ай бұрын
For a clean sleek look, if you liked cars you’d understand
@spacecoop765924 күн бұрын
What the hell is googaw
@michaeljones2253 жыл бұрын
Crazy as batshit to debadge a car 🚘
@TheEckoEcho3 жыл бұрын
Personally don't like debadge car
@Brokenddos2 жыл бұрын
I like to take off the model and engine type (if it’s on there) but keep the manufacturer badge
@kittysmith8959 Жыл бұрын
Yet you take the time to view a how to debadge a car video... ???
@Colin623 Жыл бұрын
@@kittysmith8959 out of curiosity maybe ? When I watch a video of how the moon landings was achieved doesn't necessarily mean I want to do it myself, lol.
@del7i5404 ай бұрын
Why debadge? I always wonder what the punk in the ratty car is trying to hide. 😅