It's awesome and really helpful. Your videos boost up encourage in many students. I watched your most of the videos. It is very informative and well explained. Very few people do such novel task i.e knowledge sharing on this interested topic. Thanks you so much for thinking about the students and making such knowledgeable videos.
@DrJALAGHARI3 жыл бұрын
Thank you so much for the compliments. I have done my work to help the students. Now it is your part to share these videos and channel with as many students as you can so that all may take benefit from these videos.
@pavandreamerr2 жыл бұрын
@@DrJALAGHARI Hi sir..i am trying to implement this on two area tie line biased power system.. should we have to train the both controllers seperately? because the output is not matching when we replacing normal PID with ANN trained PID..any comments plz
@DrJALAGHARI2 жыл бұрын
@@pavandreamerr yes. You have to Train both ann separately.
@pavandreamerr2 жыл бұрын
@@DrJALAGHARI sir u have modified the pid controller position from feedback to feedforward in the block diagram..if we can get that approved system pdf its very useful sir
@DrJALAGHARI2 жыл бұрын
@@pavandreamerr in two area system, the pid controller will be used in their original position. You may watch my pso video for two area system
@nargesghafeli88662 жыл бұрын
Thank you so much for your great tutorial 🙏💐🌹
@DrJALAGHARI2 жыл бұрын
Thank you so much for the compliments. Kindly do share it within your circle too.
@NaveenKumar-hy4js3 жыл бұрын
tq sir..ur very help full to us....
@DrJALAGHARI3 жыл бұрын
Thanks for the compliments.
@muddin59633 жыл бұрын
Excellent information sir.Please share load frequency control using PSO in MATLAB.
@DrJALAGHARI3 жыл бұрын
Thanks for the compliments. It will taake time for me to make video on this topic.
@muddin59633 жыл бұрын
@@DrJALAGHARIoff course, sir.
@TheFiras19742 жыл бұрын
Wondifull v good work
@DrJALAGHARI2 жыл бұрын
Thank you so much for the compliments.
@majidmohiuddin48794 ай бұрын
Sir can you please explain how to implement it for two area system separately. I tried alot but i am facing some difficulty.
@DrJALAGHARI3 ай бұрын
Thanks for the comment. You may have to apply ANN separately for each area as well as Tie line.
@concernkid9 ай бұрын
hello please what changes should I make to the matlab code if i want to experiment on adding integral to the input
@DrJALAGHARI8 ай бұрын
Thanks for the message. No need to change the code. It will work.
@concernkid Жыл бұрын
HI sir Please I have been trying to do this on a cascaded Fractional order PI - FOPID, the result is not very good. Any help
@DrJALAGHARI Жыл бұрын
Thanks for the comment. I haven't worked on this controller. I think you may need to rune or optimise it properly.
@AhmedMohammed-rm3yy3 жыл бұрын
Allah bless you ,thank you very much
@DrJALAGHARI3 жыл бұрын
Thank you so much for the compliments. My pleasure.
@hasanozkar7 ай бұрын
I applied what is shown in the video many times. However, the system does not reach the desired output or becomes unstable. Even if the regression ratio is found to be 0.99. Where am I making a mistake?
@DrJALAGHARI7 ай бұрын
Thanks for the comment. I couldn't understand why it is not giving the desired output. It is working fine at my laptop as shown in the video.
@merahmohamed23293 жыл бұрын
thank you very much Sir
@DrJALAGHARI3 жыл бұрын
Thanks for the compliments.
@FaraedoonWaly3 жыл бұрын
thanks a lot. barakallah
@DrJALAGHARI3 жыл бұрын
Thank you so much for the compliments.
@safiullah38342 жыл бұрын
Nice video sir...how can we tune more than one controllers at a time using ANN sir?
@DrJALAGHARI2 жыл бұрын
Thanks for the compliments. You have to train each controller separately one by one.
@jn92813 жыл бұрын
Sir,In case of PD controller,PI controller,I controller what must be the values of PID controller?
@DrJALAGHARI3 жыл бұрын
The actual values for any system need to be determined everytime bu doing simulation. Easy way is to use PID Tuner block then use only selected parameters such as PD, PI, I and find the best value. Kindly watch my video on PID tuner for better understanding.
@JamesBarsky Жыл бұрын
Trying to implement same but i get the following error "Error using network/train Output data size does not match net.outputs{3}.size. Error in lfc1 (line 8) net=train(net,I,T); % Start training the network
@DrJALAGHARI Жыл бұрын
Thanks for the comment. Which MATLAB version are you using. How many inputs you are using in your model.
@shahsadali20142 жыл бұрын
Can you please describe how ANN is used in voltage control in power system
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. You may kindly watch my video on automatic voltage regulator AVR using ANN for this purpose.
@jarafeyisa4769 Жыл бұрын
Hello doctor, under this lecture, the load is decreased, the controller is not controlling the output. What is the problem?
@DrJALAGHARI Жыл бұрын
Thanks for the comment. Basically I have just shared the idea on how to use ANN. For best results, it needs proper training.
@jarafeyisa4769 Жыл бұрын
Thank doctor
@DrJALAGHARI Жыл бұрын
@@jarafeyisa4769 most welcome
@nadiab29675 ай бұрын
Thank you
@DrJALAGHARI3 ай бұрын
Thanks.
@hoathai7657 Жыл бұрын
Hi, Dr. How to implement ANN for MIMO system? Thanks
@DrJALAGHARI Жыл бұрын
Thanks for the comment. Yes. You can use it for MIMO. Add the output variable in the data.
@pavandreamerr2 жыл бұрын
Hi sir..i am trying to implement this on two area tie line biased power system.. should we have to train the both controllers seperately? because the output is not matching when we replacing normal PID with ANN trained PID..any comments plz
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. Yes. You have to Train both separately.
@majidmohiuddin48794 ай бұрын
Sir can you explain a bit how to train them separately.
@dureshawarana3052 жыл бұрын
How do we control frequency in transmission lines???? without interupt GENCOs
@DrJALAGHARI2 жыл бұрын
Frequency can be measured by using PLL phase locked loop. But to control it, you have to make active power generation equal to load demand. Therefore, it can be controlled by load frequency control or load shedding scheme.
@ShivaniSingh-nx5lp2 жыл бұрын
Sir I was trying to run the code in the editor but it is showing error and no Ann window is coming I need your help
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. May I know what error you receive?
@ShivaniSingh-nx5lp2 жыл бұрын
@@DrJALAGHARI sir can I have your contact no so that I can share my error?
@World-tours3 жыл бұрын
Nice Sir 👍
@DrJALAGHARI3 жыл бұрын
Thanks
@miladzaed15583 жыл бұрын
hi Dr. when i do ginsim the created net without input so how i can solve this issuee?
@DrJALAGHARI3 жыл бұрын
Have you written the command correctly?
@akuakali6102 жыл бұрын
@@DrJALAGHARI I faced the same problem too, it only shows output
@nomad12863 жыл бұрын
sir, a heartfull thanks to you for uploading this video.. it was very much helpful..can you please give a suggestion in the change in procedures when it is two area.. since iam weak in coding, i cant deduce an answer
@DrJALAGHARI3 жыл бұрын
Thanks for the compliments. For two area, you have to use two ANN, one for first area and other for second area. Therefore, the code remains same. Only you have to use it two times. One for training the data of first area controller and second for training the data of second controller.
@nomad12863 жыл бұрын
@@DrJALAGHARI that means after the first area I move the same in&out workspace block to the second area and run ANN test with the same code.. right sir?
@DrJALAGHARI3 жыл бұрын
@@nomad1286 code will be same. But data will be different .
@nomad12863 жыл бұрын
@@DrJALAGHARI appreciate it for answering queries... jazakallahu khair
@DrJALAGHARI3 жыл бұрын
@@nomad1286 my pleasure.
@engg.w1983 Жыл бұрын
Thanks
@DrJALAGHARI Жыл бұрын
Most welcome
@QuangDiem_151010 ай бұрын
Thank Sir
@DrJALAGHARI8 ай бұрын
You welcome
@shrutiasthana44852 жыл бұрын
Hi Sir, I have been trying to implement NN in the similar manner to a step input to my plant represented as 1/(0.5s+1). I also, designed the PI controller for the same plant and with PI controller, the response is satisfactory which follows the step input trajectory. But when I train the NN model and replace my PI with it, the response is not following the step input trajectory. That means, the NN controller responses even when the input values is zero. I am looking forward to get some insight on my problem, as I am beginner and any help from you will encourage me to continue my work in this direction. Thankyou!
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. As ANN depends upon the input and output data. Therefore, try to check the input and output data. If there are some values greater than the required output then change these values. Then train the ANN. Hopefully it will work. Or you may watch my videos on ANN and ANFIs. I am not sure in. Which video i have discussed this strategy.
@AhmedMohammed-rm3yy3 жыл бұрын
Please doctor, do you have areasearch paper for this subject ?
@DrJALAGHARI3 жыл бұрын
I don't have. But you can write research paper on this model if you want. Just search for this topic in ieee explorer and science direct.
@AhmedMohammed-rm3yy3 жыл бұрын
@@DrJALAGHARI Ok ,thanks doctor
@LakshmiSatya-zh3dq11 ай бұрын
Sir,i have used the same code but it is showing error in first two lines .pls help me
@DrJALAGHARI11 ай бұрын
Thanks for the comment. What error you encounter
@LakshmiSatya-zh3dq11 ай бұрын
@@DrJALAGHARI it is showing error in first two lines ,i.e. input and output
@DrJALAGHARI11 ай бұрын
@@LakshmiSatya-zh3dq how many inputs and outputs you are using and which matlab version you are using
@LakshmiSatya-zh3dq11 ай бұрын
@@DrJALAGHARI I = input'; T = output'; net=newff(minmax(I),[3,5,1],{'logsig','tansig','purelin'},'trainlm'); net = init(net); net.trainParam.show =1; net.trainParam.epochs =10000; net.trainParam.goal =1e-12; net=train(net,I,T); the following code i wrote and i complied, these are the errors i got sir. Error using input Not enough input arguments. Error in file (line 1) I = input'; Thankyou so much for your replay sir.
@DrJALAGHARI11 ай бұрын
@@LakshmiSatya-zh3dq the data should be in workspace with name as Input. Kindly check it
@santhoshraikar40193 жыл бұрын
Sir any Matlab code for swing curve for facts device
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. I have already sent the material at your email.
@santhoshraikar40193 жыл бұрын
Swing curve program for facts device
@DrJALAGHARI2 жыл бұрын
Thanks for the comment. I have already sent the material at your email.