Visit us at www.apwdistributing.com/ Music: "The Wire" Kevin MacLeod (incompetech.com) Licensed under Creative Commons: By Attribution 3.0 creativecommons.org/licenses/b...
Пікірлер: 74
@MrGabrielallon11 ай бұрын
UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzbin.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.
@danschroeder967614 күн бұрын
this saved my day! thank you! I had water using the low pressure/soap nozzle position, but when I pulled it up to high-pressure, no water. I was able to take the orifice out with a 1.5 mm allen wrench and unclog it.
@gergemall4 жыл бұрын
This is the best and most comprehensive video on pressure washer diagnosis and repair .
@DNBDJ Жыл бұрын
Was just about to pull the trigger on buying a new washer.. but this video saved me.. slug in the filter :) thank you!
@jamesdavidson11852 жыл бұрын
You are amazing! Your video was spot on. I checked the carb, replaced the O-rings, bought a new hose....and damn if it wasnt the very first issue you brought up. Yes, 2 years ago I decided "this screen thing is overkill and not necessary". I stand corrected. Seriously, you saved me SO MUCH frustration and costs. THANK YOU!!!!
@MikeTreubig8 жыл бұрын
Thanks. This got my pressure washer working. That little tip about the little tip was just what I needed.
@gregmccarter217610 ай бұрын
I picked up approximately 15 pressure washers for free..two are honda driven 13hp cat pumps..both cats didn't pump..I found that the pumps were ran on bad water...I cleaned the entire manifold system..both cats now work super good..will cut asphalt
@bobkempa27544 жыл бұрын
Hey thanks a lot; I took your advice and worked through the machine methodically and it works just great now.
@richardbeall26444 жыл бұрын
Got mine going today with this 6 year old video. Thank you!
@taakappa3 жыл бұрын
I had opened the pump 5times.. couldn't figure out the problem.. this video helped me narrow down the problem.. thanks for posting
@APWRepairCenter3 жыл бұрын
You're welcome!
@mountainbiker446 жыл бұрын
Great video. It just helped me troubleshoot my Ryobi 2000. The pump was jumping and it was just a clogged tip. Thank you
@jonvan27856 жыл бұрын
Thank you for this video. It was helpful and solved my problem!
@BarnyDaddy6 жыл бұрын
Wow. Thanks a lot. Today I was driving in the neighborhood and up the street there was a VR2500....”FREE”. I brought it home, checked the oil and filled it up with gas. Hooked up the water and it started right up. Very little water pressure. I downloaded the manual and it said to remove the 2mm screw. To clean it. I thought they meant the tube. Your video cleared that up. I went out removed the screw and tried to stick a .050 allen through the hole. No go. I took the smallest drill I had and stuck it in my drill. The drill cleaned out what was in there. Put everything back together and held on with two hands and bingo....High pressure like there was never there before. My wife, 110 pounds of South Korean could barely hold on. I am in a quandary. Do I go tell the neighborhood they screwed up? Hell, the 6.5HP Briggs and Stratton engine is worth a lot of money. Thanks again.....you are the best,.
@user-zc7vz1ce2b6 жыл бұрын
Hey. Thanks for taking the time to do this video. I had about lost hope on my PW until I seen your video. The last part about the hose jumping and meaning you had pressure , well sure enough I changed hoses and the wand and BAM PW like a boss now lol. Thanks.
@yihchau4 жыл бұрын
Informative diagnostic triage of typical root causes. Thanks!
@johnr.60292 жыл бұрын
Wow - your video helped me figure out how to use the spray head on my garage sale purchased Generac 2100 psi 6 hp 2gpm . Thank you.
@thetruthmatters76 жыл бұрын
thank you, and God Bless you!
@jerrysmith63483 жыл бұрын
Thanks so much, bro! My issue turned out to be a clogged nozzle tip. Never would have figured out how to get it out to clean without this video. And I ended up having to drill the debris out with a 1/16" bit!
@APWRepairCenter3 жыл бұрын
Glad it helped!
@craigl95309 жыл бұрын
Thanx, VERY helpful!!!
@jj-rz8lc6 жыл бұрын
I left my petrol pressure washer running for about 10 mins without spraying. It's got no pressure/ water just squirts a little when trigger is pulled. Help/advice appreciated.
@jamesrobinson4950 Жыл бұрын
Bunch of junk came out of a spout I never use on my house and clogged filter, problem solved! Thnx!
@danielleancira67628 жыл бұрын
My gun shot off the tip and the connector just now I just have the gun and wond and quick release and it has started to build up pressure and the engine does not run with lots of power
@kalashsharma32746 жыл бұрын
hello there i have domestic pressure washer of skil brand its in working condition but once i switch it on water comes with pressire but after few seconds motor of pressure washer struggles to give out pressure only pressure washers motor runs but no out water pressure get out of it. so my question is? it can be repaired or pressure washer is gone.
@Brad.W Жыл бұрын
What I find interesting is when you buy a pressure washer for example I just bought and returned 3 separate machines because they was advertised at 4,200 PSI at 4 GPM but I could never get any of them to give me any more than 2,900 or 3,200 PSI an average of more than 1,000 PSI less than what the box says. Found out from the manufacturer that it is normal for pressure washers to be 1,000 PSI or more lower than their rated pressure and that 4,000 PSI means that's what it's Idle pressure is meaning the head pressure will be 4000 PSI when not depressing the trigger. Talk about false advertising.
@ashonpar36 жыл бұрын
I have power washer that it takes sometime to engage ,but will engage what could be the problem?
@orlandosuarez41877 жыл бұрын
I have a Ridgid pressure washer 3800 psi and has lost half of the power . Have no leaks , and the oils are ok . Any suggestion about what could be the cause to this problem ? please , can someone help me out ?
@newyay59643 жыл бұрын
Love you man
@randywaugh24386 жыл бұрын
Is water supposed to spray out of a little hole in the blue soap dispenser plug?
@williamskaliman2 жыл бұрын
Thanks man
@cherylprestero8783 Жыл бұрын
There was not a hose filter on my hose connection. How do I know if there’s debris in the pump?
@Kris94642 жыл бұрын
Im using 5/16 high pressure hose for my 4400psi 4gpm machine and im so frustrated about vibration of hoses. I replaced my cart, even replaced my old AAA pump that went broke and with the new Comet 4000psi 4gpm pump and skid mounted on truck my hoses are vibrating as hell. Do you think switching to 3/8 hose will help? Do you have any vibration problems with 3/8 and 8gpm 3600 psi? I might be switching to 8gpm near future and i dont want this vibration any more.
@nurtopaloglu57423 ай бұрын
Hello, I installed a short water spray gun on the Karcher K6 washing machine and its hose. After making the connections, the water spray became intermittent even though there was no water leakage. It worked properly when using the original Karcher gun. Which device may have the problem?
@jdomin27885 жыл бұрын
I cannot font my solution anywhere I need help!! I have a predator from harbor freight stoped having pressure
@Tyroneguy77 Жыл бұрын
I've a 2400w jet washer and it's getting water through it with no leaks problem Is the pressure isn't strong or constant. Good flow of water coming through hose from. Tap. What could be problem? When I pull trigger strong gush for a second then stall way down to very low pressure.
@mot6115 жыл бұрын
… Just a steady 10' skinny stream of water.My unit used to work great. Then it broke. I replaced all the stock plastic pump parts (which were all broken) with new brass ones. The unit ran great for a while then quit. Now it only produces a skinny stream of water which is the same with the engine running or not.I pulled the unloader and it seems OK. I mean it moves back and forth.
@SteveP-vm1uc8 жыл бұрын
I am new to pressure washing and have a question. I bought a Dewalt 4200/4GPM washer and also a gauge to keep tabs on the machine. When using a tight single tip I see that I lose a very small amount of pressure while spraying, but when using a Mi-t-m flat surface sprayer from a rental joint, my pressure dropped from approximately 4000 PSI un-triggered to 2500 PSI triggered. Is this normal?? I would think the machine would do what it has to to keep the pressure up. Or am I just completely wrong about this? I thank you for your expertise in advance.
@APWRepairCenter8 жыл бұрын
+Steve 1961P. When using a surface cleaner you are distributing the water pressure between 2-4 nozzles that spin to cover a large area. When confined to a tight single tip you will get maximum pressure from your washer but you will loose pressure when distributing it through multiple nozzles. You still have the same gallons per minute but since the water is flowing more freely through the surface cleaner's multiple tips your pump isn't able to create the same amount of back pressure as it would with a lesser flow single tip. So a drop in pressure is normal in this case.
@SteveP-vm1uc8 жыл бұрын
+APW Repair Center So aren't the jets/nozzles supposed to be half the size of your single nozzles if you have (2) on a spinning cleaner? The flat surface cleaner I rented was set up for a 3500 psi / 3.5 GPM machine.. They told me my 4200/4gpm would do a better job than their washer... Then they wanted to argue with me that I was crazy that it didn't clean at a creep.
@APWRepairCenter8 жыл бұрын
They should be ideally but not always. You will still lose pressure just by splitting flow between 2 nozzles regardless of proper gpm nozzles. A 4gpm nozzle will always put out more pressure than 2x 2gpm nozzles.
@OfficialGomez4 жыл бұрын
My washer is brand new and it doesn’t shoot out fast or have much pressure
@hersheylvr4evr6 жыл бұрын
How to replace water pump on Honda gcv160
@jacobmagut41017 жыл бұрын
My washer has reduced pressure by half and it is vibrating a lot especially the pipe and gun.. Please help
@APWRepairCenter7 жыл бұрын
Have you tried the steps in the video? I need more information.
@killuaHunter4 жыл бұрын
Check the check valves , one of them must be stuck
@Benicio5114 жыл бұрын
My pressure washer wand extension is leaking from the top, and the green piece wiggles back and forth , whats wrong
@ericsmallwoodd39777 жыл бұрын
I have a simpson pressure washer practically brand new and it only sprays a weak stream with motor on and off?
@APWRepairCenter7 жыл бұрын
I need more information. Did you try the steps in the video or the newer more complete video in the link kzbin.info/www/bejne/mGq7gqWHftaBpLs
@eddiemccomas5197 жыл бұрын
i have a pressure washer that you got to have the sprayer handle pressed all the time it build up so much pressure it boggs the motor down and its a 6hp.what causes that.
@APWRepairCenter7 жыл бұрын
It can be a few things. Either your unloader is adjusted to high or it is broken and won't go into by-pass mode. Also check your hoses and connections to make sure you aren't loosing back pressure through leaks. Your water flow can also be the problem if your spigot isn't providing the proper gallons per minute to supply your pressure washer.
@eddiemccomas5197 жыл бұрын
i took the unloader out and checked it its not stuck i dont think its going in by-pass mode i havent tryed to adjust the loader how do i do that turn it out if i turn it in wont that put more pressure to it.
@Joe-wy2bn Жыл бұрын
My pressure washer will go to 3000 PSI and then when I hit the Trigger it drops to 700 PSI, maybe the nozzle orifices are too big?
@marioz48126 жыл бұрын
Check the oil, might be low.
@jamir96283 жыл бұрын
Thank you! My tip was off just a little lol!
@APWRepairCenter3 жыл бұрын
Glad I could help!
@kirksdva83102 жыл бұрын
Je for Det pressure but everyone is different
@waylonmccrae35465 жыл бұрын
What is going on with the pump when it stalls the engine and acts like it is locked up ... any ideas ?? Thanks - MW
@minusx313 жыл бұрын
My pressure washer runs then the sound changes lower and pressure stops for a few seconds before it gets louder then the pressure begins again...
@ericsmallwoodd39777 жыл бұрын
No power whatsoever, just a steady ten foot skinny stream of water.
@conniemayo14323 жыл бұрын
U hug. I
@billypotter3831 Жыл бұрын
Nothing covered in the pump valves or unloader 👎
@leefranklin47706 жыл бұрын
Don't you know how to Fix A pump you just talk about the Child Proff Wand you should go get a Job you are Qualify for Filp a Bugar
@ivovicini41656 жыл бұрын
Jesus, I wouldn't trust YOU flipping burgers with a vocabulary like that. At least try and learn to talk before you try to talk shit lmao
@tedofuentes65254 жыл бұрын
Lmfao. You cant even speak
@leefranklin47704 жыл бұрын
tedo fuentes Ha. Ha
@1039597709798 жыл бұрын
Go home depot they fix it for 40 or 60 bucks.
@SteelStud24828 жыл бұрын
+Mr E (channel) Or buy a 40 cent o ring instead and fix it yourself. 40-60 is ridiculous when you can fix it cheaply yourself and have the satisfaction of doing it yourself.
@orlandosuarez41877 жыл бұрын
I have a Ridgid pressure washer 3800 psi and has lost half of the power . Have no leaks , and the oils are ok . Any suggestion about what could be the cause to this problem ? please , can someone help me out ?