How To Drill Tiles Without Breaking Them! No One Knows This Secret

Everyone has tiles in their home. Sometimes you may want to drill holes or break tiles. But it is very difficult to cut tiles properly. Few people know this tiling trick. Tiles can break very quickly. In this video we show you tips for drilling and cutting tiles. If you want to drill or cut tiles like a pro, use these tile drilling tips in this video.

[@samTollefson]

When I really didn't want to take a chance breaking a tile when drilling, I would make a small donut out of modeling clay and press it onto the tile around the hole and fill it with water, then drill at a slow speed. A little extra work maybe, but it never failed me. It is the heat and impact that breaks them.

[@martamachalska1801]

Jak widać jednak ktoś zna. A jak zna jedna osoba to możliwe, że tysiące innych też. No, moja potrzeba sensowności wypowiedzi dała o sobie znać. Powodzenia😁

[@Worlok1960]

Wywierciłem dziesiątki otworów zwykłą"widią" bez udaru- zapunktować i wiercić na wolnych obrotach.

[@skovbo65]

When you drill a tile just turn off the hammer function on the drill and use a piece of masking tape on the spot and you can do the drilling with an ordinary concrete drill.

[@Retrovorious]

Mine doesn’t even have a hammer function so I’m half way there already.

[@y33t23]

It just takes ages to get through the tile for me. It must be some super hard natural stone or something, took me like 3 hours for 2 holes.

[@junangeles]

@@y33t23same. My cordless drill’s full battery ran out of juice and I’m still not drilling through.

[@y33t23]

@@junangeles what was fortunate for me was that I wasn't drilling a tile that was in some sort of wall or anything, so I just switched to a brick material one and used the fast setting on a corded drill in a drill press going very slowly from small to big drill. Otherwise the drill will go red hot and the tile might crack. I put a perfectly level wooden board to drill into underneath because otherwise it would crack as well. After like 3 or 4 broken ones I finally had it down and could do one hole in like an hour or so.

[@marcellobartoletti2325]

Forare piastrelle con il percussore è come darsi martellate sulle dita,se per capirlo ci vuole un video,allora siamo messi veramente male,basta usare la testa,se non si è seccata del tutto a forza di usare tecnologia anche per cose semplici.

[@Truepatriott]

О великий мастер умеющий пользоваться специальным алмазным сверлом! Этого же никто ни когда не делал. Кстати прекрасно сверлится и без воды, потому что на стену её не нальешь.

[@lennykelly9952]

Well I have drilled tiles a lot and what works for me is take the drill off hammer action with a bradawl tap gently and score a mark on the tile so the bit doesn’t slip.drill through the tile off hammer when you get through the tile put in on hammer action and drill into the wall.When you place the plug in the hole make sure the plug is passed the tile or you will burst the tile.

[@clairestaffieri4398]

Well done. Thank you for showing us how to do this correctly. Отличная работа. Спасибо, что показали нам, как это сделать правильно.

[@Tips24H-rj9pq]

I have learned a lot from you, thank you for sharing the video

[@trampan6377]

Ese secreto lo descubrí yo hace muchos años. Si para taladrar un azulejo usas la percusión es seguro que lo rompes. La otra forma es más lenta pero te ahorra disgustos.

[@indianb1918]

Good video but adding voice would be very helpful.

[@tn9274]

just use diamond drill bit (solid tube or hole saw). work the best.

[@carlosraide4823]

Excelente...aunque los equipos son Caros.👑👑👑

[@user-dn6je6gu3l]

Громить плитку перфоратором в режиме удара, - такого зверства точно никто не знает!

[@zbigniewsidor8659]

Motoryzacja

[@maximnaumovskiy8299]

И на ударном шуруповерте включать удар(когда сверлишь плитку)надо быть полным мудаком🤣

[@florenciomendoza4626]

Excelente idea gracias

[@DrWenChannel]

Does this trick works with larger holes like air gap hole for tiled countertop in the kitchen? Thanks!

[@victormonge8755]

Muchas gracias por la información.

[@Invention75]

Good idea 🎉🎉🥰🥰🥰

[@markrickard6728]

Whats the secret?? I've been a tiler for well over 20 years & I've been using diamond drill bits since I started tiling for making holes.

[@shikhajain8488]

Wat he pour in glass between drilling????

[@markrickard6728]

@@shikhajain8488 it's just water

[@peteiswriteingnow]

I put up blinds and poles and tracks of all sorts for over 40 years, like Lenny Kelly below says gently score a small hole with a pointed bradawl then tap gently bradawl with a hammer to make the hole slightly larger then drill on slow speed not hammer action. i think i only broke 2 tiles in that time and they were about 50 years old so really brittle.

[@user-sx8fl8ky7o]

もっと画期的な方法があるのかと思いましたが、やはりこの方法しかないのだと再確認出来ました。 ありがとうございます。

[@davefarmery8180]

Just get some bosch multi construction bits , for ceramic or marcrist diamond hole saws for porcelain

[@joaobatistadasilva7732]

Você usa a máquina na função martelete ,e com a outra beca você não usa a função mrtelet

[@pietrodurso211]

Perché e' furbo

[@EduardoMartinez-mm2rf]

Te falto decir que tipo de broca...

[@pablolopescamarano2555]

GRACIAS X COMPARTIR ESTOS CONOCIMIENTOS,AHORRAREMOS MUCHA PLATA!!!!!!

[@SC.243k]

Very good

[@brubru6819]

Great video - how do you cut a L shape tile from a new tile.

[@robh9105]

Take it off hammer setting and the masonry bit will cut through the tile.

[@mariojorgepavia]

Muy buenos consejos. Gracias

[@luulemees]

According to my experience, yes you can go with impact and do what you need to do fast and effective, if the tile guy has done quality job tile wont brake. But impact hole has guite extensive edges, sometimes you need perfect edges and cant take risk that tile guy has put one tile shitty. So there are to ways todeal with it.. for diys, few holes take universal drillbit lightly larger than a hole you are going to drill, tap it lightly with an hammer while turning it on the tile to get rid of the glaze, take ceramic, glass or a masonry drill bit and drill hole on low turns. For advanced amateurs:buy normal quality drill bits for ceramic, puncturemark hole with an old drillbit and drill on low speed, dont forget to cool bit with water and charge more for installation as you are burning trough drillbits. Remeber, you allmost never drill on the ideal circumstances on the floor between two tiles, you drill on the wall on the edge of the tile

[@pabloromano4393]

Yo ni siquiera aprendi en algun lugar...la logica me dijo que golpeara lo mas levemente algun tornillo o la mecha misma con un martillo 2 o 3 veces al punto de astillar el esmalte y listo...a darle con el taladro...no recuerdo haber roto alguna vez un ceramico de los cientos que seguramemte he agujereado.

[@demiurgkoryfeusz2508]

Do wiercenia wstępnego używam wkręty stalowe( fosfatowane 3,5 x 35 mm do metalu ) z płetwą a następnie wiertło do betonu z widią. Nigdy mi się nie zdarzyło żeby płytka pękła.

[@waldemarsubocz4857]

Sproboj uzyc wiertla do szkla ono jest w krzalcie stozka na wolnych obrotach uzywajac psikacza do wody zeby nie przegrzec widii a przewiercisz cala Plytka na wylot

[@oscarvalencia3028]

Si no es capas de esplicar no monte videos

[@Sheddweller419]

I had to drill through a 10mm thick tile , so I used silicone to create a circle , filled it with water, and then drilled . Simples.

[@user-jg6wx3it1m]

Секрет простой - купить сверло для керамики! Одним сверлом насверливаю пару тысяч отверстий без заточки

[@user-pr5ey7ng3h]

Обязательно продолжайте выдавать тайны

[@guysolis5843]

I still have a bit like that in my screw gun case. I've been carrying it around for 25 year and every time I updated my screw gun that ceramic bit made it there too..

[@DenmasTV]

but, how about mounted wall tile ?

[@user-jl3tq3ho2n]

Никто не знает, что сверлом можно просверлить отверстие 🤦‍♂️

[@qanikadriu7232]

Ju lutem shumë komentet mi dërgoni në gjuhën shqip se unë vetëm këtë gjuhë nnoh,fale Inderit.

[@jjm9741]

Porcelain Tile too works???

[@Laketexomaliving]

Thank u

[@mohammedkaleb1006]

If you're gonna drill glass or tile, use a glass and tile bit... That's the big secret?

[@alessandroandrenacci2372]

At the very beginning, he tried hammer option ( crazy !!! ). The focal point is break the outside glassed surface of the tile with a hard tip of steel, then go on drilling at low speed, the tile internally is more soft ; best using water and pay attention when the bore is almost completed, the drill bit can force too much on the remainig parts and break the whole tile ...

[@dc.pentrumesteri4893]

and cutting with a sharp knife is as old as the world and is only valid for large pieces for narrow pieces of 2,3,4,5 cm, what do you do?

[@NangaiEsther-nt4cb]

Good 👍👍😊

[@MARiordan]

I knew this secret! So it is not "no one"... If you try making the hole with a hammer, it will break the tile too!

[@m3photo726]

A small screwdriver to get through the enamel by spinning it with hands clasped together, similar to rubbing a stick when lighting a camp fire. Then a few drops of water and you drill through no problem.

[@user-ri7lc5sr3d]

Есть простой,дедовский способ,просто взять керно и сбить аккуратно глазурь ,с места отверстия и всё,бери обычное сверло и хоть сито из плитки делай, всё элементарное просто

[@willbee6785]

Einstein at the ready. 😊

[@heukelummer]

you forgot to show the secret,you only showed a tile drill that you can buy everywhere

[@BlueBird18923]

if you water the portion you are drilling on tile it will not break

[@heukelummer]

@@BlueBird18923 that's not a secret..

[@user-eq5eh8gw8h]

Есть плиточное сверло называется перо всех диаметров купи и не парьте людям мозги

[@serggorovets9019]

Иносранцы,что с них взять...

[@Μπολσεβικος]

Υπάρχει και τρυπάνι για δομικά υλικά

[@johncalvin9703]

Why did you drill with hammer function - 1st drill - then selected drill function - 2nd drill - with the special bit? Rhetorical question.

[@robertyoung8785]

what secret? that's what those drills are for.

[@adrianholman4842]

The secret is just to make you click

[@markusjordantesoro2992]

this video don't have enought knowledge in how to make a hole in tiles easily.

[@rafayepez6385]

más de una vez he hecho agujeros en ese material con taladro sin usar el modo martillo

[@mikesteffes9999]

Here’s another method: diamond-edged hole saws in various diameters.

[@sawomirkosiacki1228]

Ale magik

[@user-ef6so1dw7l]

جدی.. فک نکنم ب این راحتی باشه ها.. دستگاه برش مخاد جگر.. 😅

[@Padoinky]

Yeah, ya get a drill w/ a diamond tip and wet drill it - kinda like ya need a specific drill bit for stone, brick, concrete, etc

[@mrpelexo7551]

ostia y esto lo has descubierto tu solo?

[@marypapadogiannh2144]

Aν αντί για το τρυπάνι για πέτρα, μπετόν κλπ χρησιμοποιήσετε τρυπάνι για μέταλλα το αποτέλεσμα θα σας εντυπωσιάσει!!!!

[@Mitrysm]

Просто ГЕНИЙ 😂

[@hieronimstepien4738]

O co tu chodzi? Czy ty miałeś kiedyś coś wspólnego z kafelkami, czy udajesz głupa??? Nie pal tyle trawy a porady zostaw dla fachowców!

[@qanikadriu7232]

Ju lutem komentet mi dërgoni në gjuhën shqip se unë vetëm këtë gjuhë njoh.

[@horiaioanfilip5019]

Nimeni nu stie?Rahat cu apa rece ! Sunt foarte multi care stiu chiar mai mult decat ce prezinti tu ca mari secrete profesionale.

[@stefanominiati8585]

That is, do you use a ceramic bit to drill ceramics? Damn, what a great idea. Who would have ever thought that?😂😂

[@davidfalconer8913]

Hammer function is best reserved for bricks / blocks ( or driving decking screws ) .............. DAVE™ .......

[@user-ym8lp8to5x]

Такая плитка прекрасно сверлится новым буром без удара.

[@doktorblind3012]

For over 30 years I have been drilling holes in the tiles according to illustration no. 3, i.e. with SDS drills with impact. So far, I have broken about 2 tiles out of 1000. I am a trained gas-water-heating installer. Tile layers also drill with impact and SDS drill bits. These special drills make it easier than with SDS. But this way with the broken tiles is not right, it only happens to laymen.

[@icarossavvides2641]

I have NEVER seen anyone try and drill any kind of tile with either an SDS action nor a Percussion action engaged! Think about it, if you hit a tile with a hammer, is it going to bend or crack? Just stick a piece of masking tape on the tile where you want to drill, to stop the drill from skipping/wandering, and drill with an ordinary masonry drill with no impact shenanigans.

[@davefarmery8180]

Your talking boll@x

[@axelkonert1953]

In Deutschland lernt man das schon im ersten Lehrjahr.

[@johnwheeler1629]

You can buy a special drill for the job, used on slow speed with hammer off. And do not press to hard.

[@miklosberenyi465]

Secreto para quien? Persona que tiene conocimiento hace años usa broca especial.

[@JuanDuranG]

Has una encuesta y habra un gran porcentaje que no lo sabia , o solo lee en los comentarios como le agradecen

[@sergioocampo8806]

Como se llama la broca

[@Sergei_Derevnya]

алмазное сверло по плитке надо взять для начала

[@sandycay4085]

Why were you using hammer modes on others two? Huh

[@user-rw4qh3pl5e]

Сверлом по бетону, перфоратором сверлить плитку

[@rafayepez6385]

lógicamente con el taladro en modo martillo se va a romper el azulejo pero si se perfora en modo no martillo esta no se va romper

[@JuanDuranG]

Pero no perfora

[@volodyakonopka9986]

Взять перо и высверлить шуруповертом

[@spyrosspyrou5809]

The only people who don't know this secret are those who have never even contemplated tiling.

[@user-is8wy2od1j]

Это кто же надоумил мастера сверлить плитку победитовым сверлом при помощи перфоратора в долбежном режиме? Неоднократно сверлил уже наклеенную на стену плитку победитовым сверлом. Малые обороты, режим сверления. Проходишь плитку, а дальше бетонная стена. Вот тут и включаешь долбежник. И плитка цела, и в стене дырка. Без воды. Наверное, существуют такие сорта плитки, что надо сверлить специальным сверлом с малым углом. Тогда перо вам в руки!

[@user-rp4xs2jy1t]

Никто не знает, что плитку надо сверлить сверлом для плитки, а не для металла? И ещё скажу автору по секрету, плитку надо сверлить острым сверлом, а не тупым. Только никому не говорите.

[@andrej8698]

Wyłączasz udar i wiercisz zwykłą widią , nie trzeba mieć specjalnego wiertełka. Uczysz a nie wiesz?.

[@user-vy9de8gj7w]

뮈한다고귀찬게 타일기리면되는데

[@mendelaskovski3996]

Use HUMMER MODE like the 1st one..

[@user-og8kn8pb4v]

Я все время сверлю просто победитом. Ничего не лопается.

[@georgikonqrski8128]

Пробива се спокойно с видия без удар

[@enriquegonzalez625]

Perfectamente explicado 🤣 no sabe que pueden incorporar voces al vídeo.

[@user-zx6xv3rc1v]

Сверлите буром по бетону без удара..Сверлится элементарно..Делал это сотни раз!

[@user-jd3sb9gn3h]

Замочи плитку в воде и сверли хоть гвоздем вот придумали проблему

[@spatzen4475]

how lucky you super brains exist.

[@taruMB]

Darbeli delmede tabiki kırılır o fayans.

[@krzysztofsulowski4011]

W gresie nie jest takie latwe

[@user-ot4ip1wl2j]

テープ貼って　ドリルや錐の刃先を殺して開けてました🙋

[@mairialisafi7009]

Θα το δοκιμασο

[@JarekC250]

Daj sobie chłopie spokój i kup wiertła do gresu firmy RUBI -10sekund i po krzyku.

[@zahubabaev190]

А в чем секрет - то, я еще оборотиков бы убавил и сверлышко новое взял.

[@dwill7405]

If no one knows this secret then why do so many companies make drill bits for tiles ??????

[@khal4913]

On one side, there is the "hammer" function and on the other, no ! LOL

[@ricardonunez1311]

Porque pueden su tiempo haciendo un video como éste, lo más fácil es comprar la broca ideal para Cerámica y porcelanato y adiós a todos tus inconvenientes perdida te tiempo

[@lorddiablo8575]

The other method is to soak the tiles in water for at least 30 mins before drilling ....

[@didiercoret561]

L ideal ? C est de poser le carreaux sur du cahoutchouc si possible , je dit çà avant d avoir vue la video !

[@patrickguyarnault1042]

Em português são ladrilhos ou azulejos ...

[@robertkat]

And now we all know.

[@carstenlarsen8144]

you caaaan use a normal masenry drill- but oc never the hammer addet