How to Easily Replace Your Car Rear Wiper Arm Assembly?

Follow this step-by-step guide to replace the rear wiper arm assembly on your car. Learn how to remove the old wiper arm without damaging the wiper motor and install the new arm properly aligned. Includes tips for using penetrating oil, marking original position, socket sizes, and thread locker.
Learn More: *** car-gpsdvd.com...

[@annama1486]

Incredibly helpful. Got my replacement arm on and off in minutes. Thank you.

[@oldeenglish8058]

Great video! One little step suggested - I would double check that the resting position of the wiper tip does not land on the paint work that eventually would scratch the paint. The masking tape is a great step, but the arm might need to be positioned one spline to the left to safe guard the paint finish. (due to a little slack in the motor drive mechanism) Thanks for taking the time to make this valuable instruction video, very helpful!

[@alanengland9731]

Thanks for your helpful video. My 2016 Prius recently had its rear wiper ripped off in a commercial car wash. Using your video, I was able to make repairs myself, likely saving a lot of money over what the dealer would have charged. [Stockton, CA]

[@charlesclark2917]

Thanks - my arm was ripped off in the assembly-line car wash but they found the arm and spring. Freezing at 3:50 helped me identify how to reattach the spring to the two other parts of the arm assembly in situ.

[@Vinni-2K]

mine just fell off on its own while i was driving lol

[@Vasu_Polu]

Thank you for the thorough and detailed instructional video. Changed out the wiper arm following the exact procedure and it worked like a charm. Much Appreciated.

[@jwarvmusic]

The puller tool was the thing. Napa guy let me borrow his, and it worked! Thank you so much for the tute!

[@Car-gpsdvdcom]

Thanks for your feedback!😃

[@MrEricdennis]

Thank you for taking the time to do this. Would not have thought of the tape!

[@Rbenterprises4]

I used the penetrant and tried to use an expensive puller, but the puller just broke the plastic. I finally took a small hacksaw and sliced the plastic away from the bushing, then used the puller to get the arm off. I bought an after market arm and blade. The blade, though an inch shorter, is easily replaceable unlike the OEM. Good video, thanks!

[@johnfolmar]

Pulling tool is what I needed to pull off assembly once nut removed. Thank you!

[@NickBombay]

Worked for me I needed the puller too prolly best one is a battery terminal puller it worked for me. Quick tip don't rip off the plastic base of the bolt like I did exposing the metal. Just made it harder for the puller to have something to brace to but all in all it worked thx man

[@elizabethridinger8804]

Thank you so much for this video! I was able to replace it myself

[@MuffinmanT90]

Thanks man! I didn't think you needed a puller to get it off i was working on wrapping a transit van I used some channel locks and got it but thanks for letting me know I just needed more pressure!

[@leeaaron3078]

Thanks🍺I replaced our Ford rear wiper arm by myself successfully.

[@Car-gpsdvdcom]

Thanks for your feedback!

[@davidbarkewitz7017]

This was helpful. Thanks.

[@bevpeters6891]

Thank you to the professor at the University of KZbin.

[@MrMCMarko]

I have one question, why did you put a glue for the nut, i am confused, like why would you do that, that makes a huge problem when you want to change the wiper arm...?

[@crush42mash6]

Yes, I did it. No problem however, had one problem. I put the wiper blade on the left-hand side when I put it back on and now I have to pop it up again. My fault I was in a rush

[@A100rm]

Exactly what I was looking for thank you

[@laurabrown7322]

I got a puller tool, it doesnt seem to want to budge. Even with the pb blaster. How long did you have to use the puller thing for it to come off?

[@caseypaul9418]

Huge help thank you!

[@user-cf3iz6cl5q]

Perfect! Thank you!

[@tiffanyruiz756]

Super helpful thank you!

[@mahmudbilal1742]

What the pulling tools name you are using to get off

[@Vinni-2K]

its like a puller get one with three arms instead

[@jenniferkeith9474]

This tool does not work. Any other ideas how to get it off?

[@devinmcdonald2030]

This was helpful, thank you. It took some serious effort though because it was corroded on there.

[@빛한줌]

나사까지 풀었는데 그다음이 어렵더라고요 영상 감사합니다

[@EastLA-kv2ee]

I can’t seem to get mine off, I don’t got a pulley.

[@msparky1]

Thanks for the video, of using a pulley as mine was corroded too, ordered mine from amazon and a new arm / blade all for £20 . it would of cost me 52.00 just for the arm from Halfords.

[@Andrew-fh8el]

Back of and hammer on one side and pull with your hand on the other. Took me 10 seconds and my was waaaaay more rusty looking. No need for a puller unless you really don't trust yourself. That little motor is strong than you think, it'll be fine.

[@wendyrobins5332]

The snow broke my whole arm so it's just hanging. Do you know what I need to do to fix this????

[@whatsup24_7]

A man

[@vdittycc]

The same part he has its 10 dollars on ebay.

[@MH55YT]

pretty good video, thanks.

[@Car-gpsdvdcom]

Thanks for your comments!

[@spsjason2]

I bent the arms on that tool trying to get mine off. It didn't work

[@Vinni-2K]

same for me guess after 10s of years the metals become one

[@JamalKhaffaf]

Let’s be clear. PB blaster only does its job on KZbin!

[@kerynsc2]

Obrigada pelo vídeo ❤

[@Summergold123]

Many thanks. Some some stool my rear wiper only left the nut. Peugeot quoted me £100. Always worth you tube ing before getting work done professionally. Easy when you know how.

[@Darkness-ie2yl]

so um. what model car is this?

[@Car-gpsdvdcom]

It is ford car.

[@lannybott]

⁰Thanks for the video. Subaru dealer service would not help me with this issue.

[@alexjude4076]

Thanks

[@dannykavanagh1734]

What was the clamp thing called??

[@Car-gpsdvdcom]

I will inquire with our staff, and then let you know, please wait again!

[@iamjayyxx3245]

Yess I need it too, if you can send an Amazon link I’d appreciate it a lot

[@BLASTING_CONSCIOUS_BIAS]

@@iamjayyxx3245Please go to any Advanced Auto or parts store and ask for a 3” reach X 3.1/2” spread “2 JAW GEAR PULLER.” The actual name of this tool and SKU # from Advanced Auto is W140 / GEAR PULLER. Make sure you do not get a larger one than this because the jaws won't fit behind the broken windshield wiper mechanism. Good luck. They are only $9.50.

[@BLASTING_CONSCIOUS_BIAS]

PULLER.” The actual name of this tool and SKU # from Advanced Auto is W140 / GEAR PULLER. Make sure you do not get a larger one than this because the jaws won't fit behind the broken windshield wiper mechanism. Good luck. They are only $9.50.

[@gloriagarcia-heckman7182]

Gear Puller 2 Jaw (Extractor de Engranajes) Brand: PT Performance Tool W140 2in reech + 3-1/2 spread, available at Advance Auto Parts for $9.99 + 6% sales tax [07/01/2024] ordered online and picked it up in 30 minutes.

[@wendyrobins5332]

It's a 2012 chevy equinox

[@metatronmen2431]

I lost the whole wiper arm in one of those automatic car wash.

[@pinkyanbrain9251]

Same. Never doing that again

[@allisonfernandez9628]

Same but can’t find the nut

[@acediego99]

Same it absolutely bodied my rear wiper arm and now I can’t remove the mounting bolt

[@metatronmen2431]

@@acediego99 The nut come easy, the plastic arm piece under the nut has a conic shape so with pressure of the nut gets really stuck, you need a small bearing extractor and WD40, IDK what car you have but be patient and dont hit it with nothing or you can break the glass, mine is mounted in the glass itself other cars are mounted in the tailgate body witch is easier.

[@Vinni-2K]

i own a car so bad the clamp trick did absolutely nothing safe to say its been a while since it had rear wipers

[@davidmandziuk8493]

Die grinder, cutoff wheel,..done

[@Ont785]

I just tried that, and that doesn’t work at all! Lol

[@devinmcdonald2030]

It works. I just did it.

[@Ont785]

@@devinmcdonald2030 Awesome! I bought another puller…easy peazy

[@Ont785]

@@devinmcdonald2030 I will add, that it worked for you,,, I’m assuming you mean that should work for everybody? Lol

[@olivertwist9628]

Put the nut back on the post get a hammer pull the arm away from the glass and slightly tap the post while turning the arm left and right do not smack the post hard enough to break the glass

[@Ont785]

@@olivertwist9628 Thank you for responding . I actually bought a better tool that popped it right off . The old are the pieces, the harder it is to get off . Now I have a tool that I can use in another 15 years !! Lol Thanks again

[@Trump908]

My dealer wanted 326$$

[@Darkness-ie2yl]

you could buy a car for that

[@BLASTING_CONSCIOUS_BIAS]

That's highway robbery.

[@davidgriffin4401]

Ouch

[@gpjoseph9807]

Blaster ad😂

[@shanehunt7285]

Don’t fit

[@get2it7]

Just what I was looking for 🫡