How to easily tighten your parking brake Land Cruiser 100 series Lexus LX470

[@georgedunham7311]

I love when there is a channel dedicated to fixing things on the exact car you drive. Thanks a lot mate, greetings from Australia 👍🇦🇺

[@NDN_FTR]

No matter what the issue, Chowcares has a video for it. Thanks!

[@dragosb2165]

You do not need to remove the wheel. You only need to lift the car so you can rotate the tire in order to position the hole to the "South". Toyota engineering is amazing. They keep it simple. I like your videos. Goos luck

[@chowcares]

Oooo good to know, I’ll try it next time

[@JuskoLord247]

Or you can just pull the handbrake up to 3 clicks then adjust the drum brakes tight then release handbrakes. That should give you around 5 clicks total when done.

[@nonsanemusic6985]

I had to pull mine off. Lx470 2003 oem rims. Can’t access it or even see it with them on

[@jameswallace7709]

Top tip. Pull it ok 3 clicks. Adjust it up tight. Then you know 3 clicks it binds. 4 and 5 is tight. Less is disengaged.

[@chowcares]

Mine needs to be adjusted again, but I’m lazy

[@fredio54]

This isn't a bad approach, however I came down here to say you should feel NO resistance when correctly adjusted. Any small amount is going to get things hot pretty fast, and accelerate wear. Best solution is new OEM shoes but adjusting it a few times furst isn't bad especially if you can see how much meat is left.

[@bobbyannis2901]

Very clear, precise and straight to the point. Thank you. I can now go ahead and work on my Land cruiser now.

[@markferguson4697]

A tutorial on how to change out the handbrake cables would be awesome, love your explanations on things you’re easy to understand and follow.🤙🤙

[@chowcares]

Maybe sooner than later, my cables are starting to stretch!!

[@MissouriAdventures]

Thank you! I didn’t know this was such an easy job. I’ve needed to do this for the last 3 years. 😂

[@RoadDogsRehab]

Oh, thank you. Took longer to jack up, remove tire, and replace tire and lower than it did to figure the invisible turny-thingy out and adjust!

[@twilliams1755]

Thanks! Just noticed mine starting to roll onto the parking pawl. Also next time you should invite your buddy Jack. Jack Stands! Stay safe.

[@dirkvandilbeek9820]

That video helps me a lot for adjust with the little inside wheel , thanks

[@chowcares]

You’re welcome

[@cliffBMRC]

Another Excellent Video and used on my Land Cruiser 1998 and 2001. Thank you.

[@fufanumitch]

Thanks! I have a parking brake again!

[@dennisvanvreden8018]

How do you replace the cable?

[@seahawksforever9504]

What happens if it's too loose? Would that cause the wheel to shake?

[@beryS_eslO]

Have a nice day.I have 2000 VX 100. How can I renew my carpet.What is carpet prt.number? Thanks for corporatıon.

[@rahalati]

Thanks for sharing. What do you think the cause is if the handbrake clicking does only one click and only when it reaches all the way up. I am not hearing the those many clicks you mentioned. Even though I was able to adjust the brake at the tire and both are giving reasonable resistance

[@chowcares]

U might want to check the handbrake mechanism. U should hear more than one click

[@scotttate7012]

Thanks Chow! Your videos are great!

[@chowcares]

You’re welcome!

[@niculaiometita8559]

Salutare ! Cand reglezi sabotii, maneta este sus sau jos?? Multumesc !

[@wesphia]

Awesome! I need to do this on mine!

[@chowcares]

Usually they do need adjusting

[@mackdelarocha]

I can’t rotate the wheel to get the adjustment hole to the bottom

[@chowcares]

Release the hand brake to rotate

[@niculaiometita8559]

buna ! In timpul reglajului, maneta de frana este sus sau jos??

[@afei_lx4709]

Maybe I missed, but you released the e-brake handle to rotate the wheel to align the hole. However, do you need to pull the brake handle up for about 4 clicks to do the adjustment?

[@chowcares]

No, leave the e brake lever down

[@mochi12342]

Much needed video! Question on my 99 I recharged my ac but now its blowing but not cold any idea.(Maybe thinking you've ran into the issue before)

[@chowcares]

Thanks! I haven’t messed much with my ac system (it’s been working fine so far), but I’d check that the compressor in engaging when u hit the ac switch. If it is, check that the condenser and lines aren’t clogged. If you’re not too familiar with the ac system, I recommend taking it to a reputable repair shop and at least having them check it out

[@mochi12342]

@@chowcares you are the best thanks ill post your videos on the landcruiser groups to get you more views.

[@ItsNautique]

Perfect video, thank you!

[@chowcares]

You’re welcome

[@fatheadmeetoo2891]

Another great video

[@prius.killer]

Great video thank you so much

[@hafizmasoud]

Great & Useful Video

[@NoName-nk8sc]

Thanks .

[@ausboy9251]

Great vid mate

[@DanielTejnicky]

yea my handbrake is virtually nonexisting mild hill is enough for the cruiser to ignore handbrake entirely - I dont wannta just use P and rest entire weight on the transmission (I mean that's what I was doing so far, but I park on level ground) =c this could prove useful

[@chowcares]

Try to adjust, but if you max out the adjuster and it still doesn’t lock, it might be time for new brake shoes/rotors

[@KoolHandLuke22]

I can’t get even one click on mine. Just the opposite problem you had? Too tight?

[@ghulamyasin6447]

Sir make video throttle body video

[@chowcares]

When it fails I will!

[@cooperbraidwood7204]

Is you car pretty much the same as a 105 series

[@tomhouston9985]

Probs more an 80 series..??

[@tomruppenthal6760]

Prior to adjustmnent, I'd keep tighten up a couple/3 lugs to make sure the rotor/drum is riding true.

[@chowcares]

That’s a good idea

[@bencandee2487]

Thanks!

[@chowcares]

You’re welcome!

[@MisterMemo]

BoOM!!!

[@chowcares]

There we go!

[@rileyfox4799]

This isn’t handbrake adjustment, this is purely drum brake adjustment.

[@chowcares]

In this case, The hand brake is a drum brake