How to Fit a SC Projects Exhaust to a MV Agusta F3 - Installation Tutorial (675 & 800)

[@drewthorne3176]

Great instructional video and paired with your sound comparison vid, I am fully informed on my SC purchase and install. Thank you. One note, and this is a personal preference perhaps. Not knowing the max temp of the SC pipe mounting lug under track riding conditions during Summer, I am a little concerned on the captive performance of the nylon lock nut when exposed to higher temperature. As such, I think I may go with a this fastener option on the back side: stainless flat washer, stainless split lock washer, stainless nut with high temp thread lock.

[@RossPerryProductions]

Hi Drew, great advice, I have done a few track days and I had a look its held up, however a good spring washer would definitely do the trick. Ross

[@Stu-SB]

I just fitted same can, piss easy, knocked up a piece of flat Stainless Bar to support the two rear most bellypan parts as removing the OE system leaves both the fastener holes redundant.

[@RossPerryProductions]

Sounds good, will give it that little bit more stability. Ross

[@Black_Gold_Saw]

holy f*kn sh!t!!! I know its an italian bike, but there's a frikin lion in there (@8:13)

[@RossPerryProductions]

Doesnt sound bad thats for sure, you should hear it on the track, I need to upload some videos

[@mattileblanc2161]

Did you also have to change the ecu or flash anything?

[@RossPerryProductions]

Hi there, No I actually spoke with the MV specialists here in Sydney and they advised me its not needed as its an adaptive ECU as I only changed tail pipe it will re adjust, if you was changing it all the way from the manifold you would need to re-map. Ross

[@mattileblanc2161]

@@RossPerryProductions I bought the new F3 800 RC which comes with the race kit. Was considering doing it myself but I also got the Race ECU and I am not sure if I would have to flash anything.

[@RossPerryProductions]

Hi Matti, sounds good, I would suggest getting the pros to do it once you start talking about remapping etc.

[@monokaya6254]

How is the inlet of the mv agusta f3? Coz i want to put a replica of sc project on my f3 but i dont know which one will fit

[@RossPerryProductions]

Hi there, the outlet side of the manifold is 42mm diameter. Ross

[@monokaya6254]

Thank you very much!!

[@edgarperez9365]

Se ve mucho mejor con el escape triple

[@RossPerryProductions]

That depends what you like, also the triple exhaust is over 9kg and the SC Projects under 1kg. Ross

[@nameless5r]

I couldn't do this to my f3, it's like telling Da Vinci, the Mona Lisa needs a different smile.

[@RossPerryProductions]

haha I track mine a lot and the standard can weighs in just under 10kg the SC 600grams, I sometimes put the stock one back on.

[@nameless5r]

@@RossPerryProductions I get it, when it comes to performance, you gotta do what you gotta do. 🤘

[@RevMonkey]

Nice! I can confirm that the SC Project exhaust looks and sounds amazing on my MV Agusta Dragster. Very well made too. Sounds mad in the tunnels in kzbin.info/www/bejne/fJ7WhoiPYsZ0oKM I had a nightmare getting access to the back of the screws but well worth it. Your video helped me decide, thanks.

[@RossPerryProductions]

No worries thinks for watching. Ross

[@jashanf3]

Considering doing this to my f3r 2022. Any cons?

[@RossPerryProductions]

not performance wise no. For me its the first bike I have had to rise with ear plugs as it is very loud haha

[@j_dlos]

where can i get that product ?????

[@RossPerryProductions]

I bought mine from MVP in Parramatta Sydney