Nice pool! I could really enjoy that today. Thanks for sharing Don.
@DonDoesStuff4 жыл бұрын
Thanks, CeCe!
@simondalton82953 ай бұрын
Thanks Don. Great video. My pool is almost exactly the same shape so that really helped
@DonDoesStuff3 ай бұрын
Glad it helped
@lorae75 ай бұрын
Thanks for the video was hoping you’d show how to put the straps on around the angles but thanks for the video
@fabiennehoogewoud118011 ай бұрын
Hi Don! We just got a cover and are looking for some tips. We didn’t cut it (yet) and we don’t have the roller system. What is the best way to remove it neatly without getting leaves and stuff that are on top in the pool? Unfortunately we have a lot of trees around us… thanks!
@1908Rick2 жыл бұрын
I have an odd shaped pool that has one area that's a bit wider than the cover. What kind of tape would you recommend to attach a piece of the cut off scrap in the place where it needs to be wider?
@marcodeluca40687 ай бұрын
At the end I notice you went in a few feet then attached the clips other videos attach the clips at the end of the cover is there a better reason for doing it your way?
@DonDoesStuff3 ай бұрын
Yes: My pool is an elongated octogon, with the roller suspended over the full width. So the clips need to be attached where the roller is. If your roller is secured at the end, attach the cover at the end.
@jeffloewi56327 ай бұрын
Nice pool and good video, but, you could have showed how you attach the cover to the roller and showed the roll up process. Did I imagine you have a Sharpie that writes on a WET solar cover? Mine doesn't. Also you seem to be attaching the straps somewhere other the the end of the cover but again you didn't show that process. Thanks.
@tinaward10233 жыл бұрын
The package says Not to trim it, but it doesn't seem that it would harm it... sooo why does it say not to?
@DonJoyce3 жыл бұрын
Hi Tina! That's kind of odd. Mine did not say 'do not trim' and was certainly easy and had no negative consequences...it's just like super heavy duty bubble wrap. That said, given the message on yours, you may want to consult with your retailer or supplier! Have fun!!
@Brandon-gx9nn3 жыл бұрын
This helped! Thank you!
@DonDoesStuff3 жыл бұрын
Glad it helped!
@richardlehtonen2784 Жыл бұрын
G´day Don and others. I have an above ground pool whre the walls sort give it a slight shape of several figure 8 or bulges. Wood decking made it really nice, My question is what your thoughts are regading these bulges. Should I try and follow them or jus cut straight along the most inward point? Or other thoughts! Thanx for sharing your great stuff!
@DonDoesStuff Жыл бұрын
I would try to follow the curves in order to keep as much covered as possible. Worst case if you mess it up, you can still cut it straight.
@troysansone90232 жыл бұрын
Hey Don, just curious what’s the purpose of cutting it? Wouldn’t it be easier to take the cover off if the sides were sticking out of the pool? Is it less effective if you don’t cut it? Thank you Don.
@DonDoesStuff2 жыл бұрын
It looks neater trimmed. Also really hard to roll it up when it is not laying flat.
@moreno64172 жыл бұрын
Does it need to be trimmed to the skimmer or leave space there?
@DonDoesStuff2 жыл бұрын
You really don't need to do anything special. Just cut it straight across the skimmer, with no extra space and no indent.
@dieselxdan2 жыл бұрын
Don - bubbles side up or down?
@DonDoesStuff2 жыл бұрын
Bubble side down! Thanks for watching!
@LubaLuba13 жыл бұрын
Hi i have a "L shape" pool what would be the best cover to buy the size is roughly 15' by 30 then L's out to a 8' x 8' at one corner ?
@DonDoesStuff3 жыл бұрын
Gosh, Luba! That's a tricky shape! Two pieces would require 2 rollers....1 piece would be awkward to roll. Did you try asking a local pool company?
@jamesmartin32583 жыл бұрын
Different videos say different things about how close to trim the edges. What is your advice? Should I let the cover go up the sides a bit or have it flat on the pool just touching the sides?
@DonDoesStuff3 жыл бұрын
Hi James! Ideally, the cover should just touch the sides. Two things conflict with this goal: One, the cover expands and contracts a bit with temperature, so the 'fit' will vary. Second, you need to be able to easily roll it in and out...and a perfectly smooth, even capture onto the roller can be tricky, especially if there is friction from the cover going up the sides. So....my recommendation is to trim it such that you have a small (1cm or 1/2 inch) gap between the cover and wall. That leaves room for expansion and minimizes friction. And, hey, we're not trying to get a hermetic seal...just good thermal coverage that looks nice!
@donny60162 жыл бұрын
Hello, Don thanks for the video! Did your cover some with two plastic sheets? Mine did and I am not sure what they are for.
@DonDoesStuff2 жыл бұрын
They want you to cover up your cover when it's rolled up. Protects it in intense sun..but not crucial.
@cliffmorgan31 Жыл бұрын
@@DonDoesStuff- The sun’s heat will pop the bubbles several layers in when the rolled up cover sits in direct summer sun… It traps the heat in the layers with no possible escape for that heat. We live in HOT high desert, so intense solar rays.
@Happydudegrows Жыл бұрын
Thanks bud 🍻
@garyinmarz89388 ай бұрын
You would think they're would be another way , instead of this cheap plastic that usually don't last more than 3 summers. But until then Thanks
@user-pw9gz9cg5t8 ай бұрын
I hear you! I go through these things like crazy- prob every 3 yrs like you said. I know covering it up all the time would help, but seems a bit overkill to try and have something over it when its not being used. I try and throw a tarp over it during the winter when its just sitting on the reel out in the snow!
@dvaleauto7763 жыл бұрын
Bubble side down....tk u 👍
@DonDoesStuff3 жыл бұрын
That's right...bubble side down. And if you're laying sod, it's green side up. That's it...that's all I know.
@MrThe1234guy8 ай бұрын
Wouldn't it just be easier to draw the shape on a hard surface and then make your cut