How to Fix Broken Sprinkler Heads

[@sunshine7764]

Thanks I’m a single woman this helped me fix my sprinkler

[@wenzwenzel2529]

Super helpful. A couple of things to keep in mind. These things come in 1/2 inch and 3/4 (and probably other sizes). You can buy converters between sizes. Also, one end is male and the sprinkler is female. And, if your sprinkler is super deep, you can buy extenders (some of which are male/female which is perfect) in many sizes. Some come in sizes, with new threads every inch or so, so you can cut them to a specific length. Go forth and fix stuff!

[@carrieohagan9131]

This video helped me fix my sprinkler heads! I’m a single homeowner so very grateful for all the detail. Thanks.

[@mikeoxmaul5062]

I found taking the head off and running the system to be helpful as well. It was insane how much mud came shooting out of that pipe.

[@awongutume]

Something not mentioned, it would be a good idea to cut a circular or square swath 3-4 inches deep around the sprinkler head to remove grass. Remove carefully as you would want to replace on top after repacking dirt in the hole dug after repairing or replacing the head. This way it will minimize any need to replant or reseed the area.

[@andresfelipemoscosohernand2371]

Thanks man. The shot at home depot was great. It clears things up a ton.

[@fastdude2002]

Always shovel your dirt out onto a piece of plywood or cardboard and not just out onto the lawn. This way you are easily able to recover all the dirt to put back instead of losing some into the lawn and end up with a low spot around the sprinkler from losing some of the dirt. also use a shovel to cut a circle or square a few inches down around the sprinkler and then pull out the lawn plug and place on your board. His way after replacing the dirt you can replace the plug on top and usually you can’t tell you just dug up the sprinkler.

[@JP___3ST.88]

Thank soo much this extra tip help a lot

[@meowmeowkitty9825]

Thank you for the instructional video! Very informative. I’m a single mom and have to be miss fix it so thank you for the help!! 💖

[@ElectricBlueJoshR]

Exactly what I needed to see. Video helped me replace a broken sprinkler head on my own. Thanks!

[@jamieford7084]

Do you have any videos on how to replace the elbow if it gets broken. No one is showing how to do that just replacing the head or taking out a riser. I can’t get the elbow out of the supply line.

[@cspill99]

I have an old copper irrigation system. what's the best and easiest way to rise the heads to the current grass level? The current heads don't even seem to be solder on the pipe.

[@JohnBrown-z2u]

That ring thing on the top...are those standard sizes? I ran over one with the mower and broke one tonight. I need to replace the ring and nozzle. I'm pretty sure it's fine underground.

[@GeeseSeason]

I was able to fix my broken sprinkler head for 10 bucks after watching your video! I had no idea how to fix it before. Many thanks for this!!!

[@M14SINAL0A]

I noticed this was in front of your home..i have same problem...do i need to shut of water from main line in front where sidewalk(city) is..or as long as my valve is off i can do this??

[@MarkFauntleroy]

As long as your sprinklers are running off of a separate supply (like a well) just turn off the pump to make these repairs. No need to shut off the main water unless your sprinklers are running off your home water supply.

[@M14SINAL0A]

@@MarkFauntleroy ty i appreciate the reply..much help thanks

[@dannyhaaz1573]

Hey Mark, thanks for sharing the knowledge. I am currently sleep deprived but I do not recall you using teflon or plumbers tape to enhance leak free connections. I use plumbers tape at each connection. May be overkill but not that expensive, but again thanks for sharing the knowledge.

[@doodlebugvideofun2001]

As Danny said, it is always a good idea to use Teflon or plummers tape to make sure that there is no leakage. It’s annoying to have to put on, but it can’t hurt anything and it can actually prevent leaks, so I highly recommend doing that in the future.

[@ElleMarieSteszewski]

How do I fix the springkler like in the beginning of the video where the water is just pouring out?

[@carlogarcia209]

For the riser sprinklers how do u know if you need replace the whole thing or just the head?

[@benjaminnguyen9997]

Is the sprinkler head too low? Would a 1" riser helps? Should the sprinkler head be level with the grass? Nice and clear video.

[@fernandoalmader9819]

Thanks for the thorough video. Working on the sprinklers here but didn't know where to start.

[@MannyLeyva]

Way easier than I thought.. thanks for sharing... I loved that you showed the price also the types at home depot.

[@deepsahoo5297]

Thank you so much for posting this. You literally saved my day with this video!!!

[@angelahogerhuis1231]

Do you need to turn the water off before replacing the in-ground pop up sprinkler? A different video I watched said it is a must.

[@alexm2866]

The control panel controls the water that goes into each zone. As long as the particular zone you are working with is off at the panel there will be no water in the lines. Hope this helps. Very detailed video Mark. Thx for sharing.

[@doodlebugvideofun2001]

They are correct. If you do not turn the water off, not only will you get totally soaked, but your hole will fill up with water which just makes everything way more difficult.

[@kevinpoweron]

Your video is excellent. Thank you very much, it saves me a lot of money for DIY

[@SirensOfWA]

I watch this video every day. I already new how to, but I like watching the vid!

[@ekasusilo]

what type/name of grass you have on your lawn?

[@jimfrider6778]

Try to install the new head flush with the grass. Add a new taller riser if you use the same size sprinkler head size to get it flush with the grass. There female to male risers that will allow you to add a few inches of height by simply screwing F-M riser to the old riser. There are also tools for removing sprinkler heads without digging a big hole. If you have a lot of heads to replace that is much easier than digging holes all over your yard.

[@doodlebugvideofun2001]

As Jim said, it is very nice to have a sprinkler that is flush with the ground. Over time, the grass can grow so thick over the sprinkler that, if unmonitored, can actually block the sprinkler from coming above the ground. This can flood the ground and it can’t be all that good for the sprinkler head.

[@CocoBark]

Yes! Thanks for showing all your steps! Very thorough and helpful video!

[@juanmartinez7452]

Thanks for the video I didn’t know how till I seen this. Sure feel good about myself that I m able to fix my stuff without paying someone else to . 👍👍👍

[@1jantheman1]

I enjoyed going on the journey with you.

[@mariobeans]

first of all dont buy sprinkler parts from home depot or lowes... Go to your local plumbing supply and stay away from ORBITS, TORO and K Rain! Go with rainbird. -an irrigation tech

[@BRISTOLFORCE2009]

no, go to Lowe’s and buy sprinklers there

[@larinoriani]

Would've been nice to see the results...

[@neilmacleod5371]

My land lady loves to jump on the mower and buzz around the lawn is if she is at the Indy 500. And she just clips the tops off any sprinkler head that has not retracted the full length. I have told her countless times to walk the lawn first and make sure the heads are all down , she is just a little bitty thing so I have being changing the broken heads for her. Now I hide the keys for the mower , takes me less time to mow the grass than to run into town and pick up new heads every week ( 35 heads in seven sets of five )

[@AngelBayyBee]

Do we turn water off when fixing these?

[@leaguecitysmokeshow8088]

Fixed! Digging a hole around the sprinkler head was backbreaking! Thanks again!

[@richardbowers3647]

Yes, yes! You, sir, were down on your knees! Typical for a lawn contractors, but not for a home owner. Just saying.

[@danwhite3227]

Well I guarantee you'd hate my job then. Underground plumbing and utilities. Digging ain't that bad once you get used to it.

[@JoseGonzales-ul9sv]

@@danwhite3227 I been digging for 4years n I don't think I will ever get used to it

[@zachtobias6583]

I just went in after watching this video in 2024 and these same heads are now $9.25. I should have checked the date on this video to manage my expectations haha

[@gonzalezajason831]

It’s really crazy lol

[@cancelcasey]

That 3 inch sprinkler is below the dirt level, is there a reason you didn't replace it with a 5 inch body?

[@cancelcasey]

NVM. That four inch was still too low though imo good video though

[@heroknaderi]

Very cool I did the same thing at my childhood house I have some 3 inch pop up sprinkler heads that I replaced with 4 inch pop ups👍

[@anon2414]

3:10 they aren't longer because you "need to go further down to your pipe" they are are longer in case you need to pop up higher over taller grass.

[@Acsirrigationinc-supply]

We added your video to our blog. Good information!

[@MP-nj1qy]

What if the pipe is broken in the body that’s sticking out?

[@deborahcicconi5600]

That sprinkler looked to be sitting way too low. Am I wrong?

[@tfustudios]

Anyone ever have the new sprinkler head break, once the system runs? That 'Rain Bird' used at 10:00 was what I'd replaced.

[@bmlandmanagementco4981]

Can you imagine doing 40 of those? I got 40 of them in my backyard alone. I’m gonna change them all out this coming winter.

[@GreggBursey]

Super helpful and informative video, thanks!

[@garyw7081]

Thanks, Mark; this is a helpful video!

[@killerbuellxb12]

Exactly what I needed to see, great video and awesome job at explaining the steps as well as what to look for!

[@hankpaloci6909]

What if the threaded nipple that comes out of the pipe is busted?

[@doodlebugvideofun2001]

It depends on if you can get the threaded nipple off. If you can you can, you can just replace that part but if you can’t the may end up needing to replace the entire upward section of pipe. This is a fairly labor intensive process, and will require lots of digging.

[@hankpaloci6909]

@@doodlebugvideofun2001 thanks! I took care of it! It wasn't to tough for an amateur like me. I didn't need to call a professional.

[@JBsBBQ]

Saved me a couple hundred bucks today! 👍🏽 Thanks

[@americanconservativeuniver860]

Very helpful. Thanks.

[@LEOPOLDINAVaz-o3q]

Good explanation

[@survivor4776]

Thank u so much🙏🏾👏🏾🎉

[@ProflexFitness]

One time my lawn guy broke 6 sprinklers, with a combination of techniques: 1) with the weed eater 2) running over the whole sprinkler with his Zero Turn Law Mower 3) not looking where he's stepping and just walks right on top of the sprinkler head. W T actual F. I now charge him $5.00 per broken sprinkler. BUT He still breaks them E V E R Y T I M E - he comes to cut the lawn. My whole existence in this World is to Fix what Other people Break.

[@bigpicturethinking5620]

You should clean and spray paint the exposed white pvc. It degrades in uv light and will get brittle

[@gasparrodrigues8552]

Great job!

[@tracezachdaniels4264]

SO SHWEEEETTT...much love Tee with LIONS NAMED LEO.[the music worldwide} and soooo cool...thanx..!!

[@wilfredotorres9289]

I'm still getting a knocking noise coming from the main water line to the system...

[@MarkFauntleroy]

Probably large air bubbles trapped somewhere in the line. Have you tried unscrewing and removing the head at the last point on each line and letting the water flow for a minute while the head is off? This might help flush the air out. "Noise Is Coming From My Sprinkler Valve | Hunker" www.hunker.com/13404597/noise-is-coming-from-my-sprinkler-valve

[@ashleysmith6884]

Thanks for sharing. Very informative

[@noeeon9910]

What he removed from that riser was a shrub adapter and nozzle. That nozzle was actually a rainbird 12van nozzle which could have been adjusted to spray at any degree... might have saved him some money and trip if he knew that.

[@deltajohnny]

Awesome video, really helpful. Thanks!! 👏👏👏👏👏

[@aznsketcher]

thank you for the video! got a bad sprinkler right in the middle of my yard. I know because I have a patch of yellow grass starting to grow right in the middle of the yard! :P (hope it's an easy fix like this video)

[@mariay.279]

Very helpful. Thx.

[@anthonywilliams5624]

Really appreciate the video! Thanks so much!

[@wawiraqi5129]

That what I did to my sprinkler heads but now the got leaked from the top i have no idea what is the wrong please help me

[@doodlebugvideofun2001]

I might have been able to leave a helpful reply but I cannot understand what you are even talking about.

[@stanhafers2462]

You probably have an adjustable head they leak around the pop-up nozzle right out of the box

[@alialkhafaji8607]

very helpful, thank you for your time and effort.

[@nathanhancock5923]

Great video like how you explain and showed every step helped me out a lot

[@retrohitstributes8781]

Solid vid, sir. Thanks!

[@skenendoa]

Everything reminds me of her 😔

[@lucassanchez5560]

Sprinkling and getting the grass wet, tapping it for comfort, the sound puddles make as you step in, digging the hole, adjusting the pressure in the nozzle, turning her 180°, making sure the head has free motion, and of course fertilizing so it can grow. Lol i hadn't thought about this until i read your comment.

[@raquijada74]

You should have thousands of laughs

[@thatswhatshesaid1812]

😂

[@samoanshine]

🤣🤣🤣 I like when I find comedians in random places. Thank you for the laugh haha

[@dumbledore192]

Omg, such a hidden talent at random KZbin comments. Dude you made my day 😂

[@susanrocco3788]

Thank you It sounds doable

[@rajanmathai]

Great video. Thanks for your time

[@kimberlyd5379]

Thanks so much!!

[@saudaminishrivastava7373]

Hi Mark, thanks for this video. it was helpful. I have two questions . Firstly what is the first sprinkler that you show in the video that is supposed to spray in a 90 degree angle called ? And secondly how do you go about replacing it if the white pipe underneath it is broken? ANy help would be appreciated. Thanks

[@SteveMancia]

Man, the most critical part was missed. The video showing the sprinklers in action

[@ksimp222]

So helpful! Thanks!

[@GKD41]

You lead off with a certain problem but do not show how to fix the broken fitting, in my case cars driving over the head.

[@michelmartin2930]

on one of my station when he change to that station it say fuse and jump to the next where is that fuse ?

[@noeeon9910]

There is no fuse. The valves solenoid needs to be replaced.

[@demichahrumph7362]

This helped me a lot.

[@maxquigley9524]

You didn't show what causes the gusher.

[@GURUKHAN_OG]

Very good and useful video! And good job KZbin!😂

[@paulmarkum1531]

Great Video Mark. Thanks for making.

[@donhgr]

Should have raised the sprinkler a couple inches

[@larryfapohunda7761]

Great video. God bless you

[@leaguecitysmokeshow8088]

Thanks for this very informative video. On my way to Home Depot!!

[@rontrellboone5139]

Great video, thanks man.

[@toby.maximillian]

Just thought that they were supposed to Be flush with the ground. But this works too

[@reviewsjustcuz1437]

You know they are real af when they ain't even wearing shoes.

[@ceva321]

I watched the entire video but did not show how they worked after ????

[@myrnavillanueva7566]

Wow, that was so helpful.

[@patmclaughlin107]

You are THE man!!!

[@casperthedog4957]

It’s January 2023 and these things are now around $15. 😢

[@miamitreo]

Gloves for your hands but no shoes lol

[@MrSparkymike1]

Check out the DIFFERENCE IN PRICES NOW from April 29, 2017!!!!

[@Darwinist1]

I'm in South FL, come fix mine...LOL. I got to correct a problem I have. I don't know what happened but I think one of my sprinkler heads blew up or something because when it comes on, it's a damn fountain flooding my lawn. I will dig in tomorrow morning and get to the bottom of it. Thanks for the video.

[@nolimitsmind]

Thank you 🙏Mark

[@stephanieknights6567]

Very helpful video, thank-you

[@P4c247]

My piped is cracked above ground can I cut it and not replace the entire pipe it is glued at its base

[@barbarabolton2067]

thanks so much it was a great I learned a lot a out putting a sprinkler head in

[@saral161]

🙏🙏🙏

[@temperso9533]

Instead of wasting on digging he could've taken off the head and flush it. I always do that and they always pop up back out .. But it's better to switch the old

[@jsrt8677]

How do you flush it once you take it off?

[@ScantPear]

0:30 just re adjust that sprinkler

[@urrow]

if you have the zone off then No water will come out.

[@kevinjames9724]

That's not necessarily true, if you run a test, there is usually always residual water in the line. I had to replace about 6 sprinklers in my system, the sprinklers located lower on my property almost always had water that would rush out as soon as i removed the sprinkler. What I did when I ran into this situation was have a piece of small wood to sit under the elbow which gently lifted the fitting high enough to safely screw the new body on without dirt issues.

[@ken48827]

Did you notice the price of these heads? Try $15 at Home Depot in Florida.

[@stanhafers2462]

Not what he is using his is a fixed spray no oscillation the one you are looking at has more adjustments and features. If I were him I would use some tape on those joints.