How to fix carburetor overflow problem in any motorcycle | Petrol overflow (pulsar 150)

In this video you will learn how to fix carburetor overflow problem in any motorcycle. Overflow problem can cause low millage and you have to look for it by inspecting the drain pipe under the carburetor . If the petrol is leaking after sometimes then that means you have a overflow problem and for repairing it or to know the reason behind it you have to open the carburetor.
To open the carburetor you have to first OFF the petrol supply from the petcock and then drain the float chamber. Then remove all the cables and senors or pipes and loose the claps from the air filter side and best to open the other side from the head. Once everything is removed and the carburetor is free then push the it from one side and pull from other end and it will come out easily.
Before open the float chamber do clean the outer surface if its to dirty , then open it and access the float needle and float. inspect the float for puncher and float needle rubber tip for wear (replace if its completely wear of) , if have dirt deposit on it then clean it with a clean cloth and also check and clean the inlet hole with air or throttle cleaner.
Once everything is cleaned reinstall the carburetor then fit it to the motorcycle and check it by ON the petrol supply for the petcock.
TOOLS AND OTHER THINGS USED
- SPANNER 10 MM, 12 MM, 8 MM ( BUY LINK - amzn.to/2Vy2Lvy )
- SCREWDRIVER ( BUY LINK - amzn.to/3mADQ6F )
- THROTTLE CLEANER ( BUY LINK - amzn.to/31F1ING )
- PIECE OF CLOTH
MY GADGET AND KZbin EQUIPMENT'S
- MOBILE - GLAXY GRAND 2
- TRIPOD ( BUY LINK - amzn.to/32hlMWx )
- LOW BUDGET TRIPOD ( BUY LINK - amzn.to/3uSm7vg )
- MOBILE HOLDER ( BUY LINK - amzn.to/2QwfsYQ )
- BEST MICROPHONE ( BUY LINK - amzn.to/3smWLnk )
- ANOTHER GOOD MIC ( BUY LINK - amzn.to/2Q4wgpO )
- LOW BUDGET MIC ( BUY LINK - amzn.to/2OWLb4Y )
- TRIPOD WITH MOBILE HOLDER AND MIC COMBO ( BUY LINK - amzn.to/3sjao71 )
HOPE THIS VIDEO IS HELPFUL FOR YOU
THANK YOU FOR WATCHING
MORE VIDEOS
How to clean petcock valve of any motorcycle - • How to clean petcock v...
How to check and change a carburetor diaphragm - • How to check and chang...
How to clean or service a carburetor of any motorcycle - • How to clean or servic...
How to remove a stuck caliper slide pin - • How to remove a stuck ...
How to find and repair the coolant leakage in a car - • How to find and repair...
How to fix gear lever slipping problem in any motorcycle - • How to fix gear lever ...
How to clean air filter of any motorcycle - • How to clean air filte...

[@ueminem]

Float needle and float changed and my problem solved. Also I cleaned the carbeurator. Bike is going rocking. 2007 model pulsar. Total cost. Around 500 rupees

[@SAIREPAIR]

nice

[@dj_trevor456]

Very smooth video

[@paullekman7690]

Even if it was without subtitle I understand it. Very good video to see everything up close what you do. New to try to repair myself.

[@supermilitia5138]

Very informative video 👍

[@emonbiker]

thanks for the video ❤️

[@nijilek9886]

Helpful thanks broo

[@sarfrajahmed5151]

Badi jabardst video bro

[@amitpotdar9976]

Thank you 😊

[@vijaypatil5222]

thank u for vdo. my avengervhad same prob

[@mrnarendramenariya2901]

Thanks ji Sir

[@itivlogs1649]

good work

[@kriskolassery4396]

Very informative video and excellent explanation

[@aneeshbhargavan465]

Very good presentation

[@SAIREPAIR]

thank you

[@suhailkhan8963]

Very good

[@amangulia4441]

Thanks bro

[@crezy..sachon]

Super sir

[@balsonnaoshekpam6240]

Mera yahi problem hai.... Thanks for the video Plz show a video about Engine idling problem

[@SAIREPAIR]

ok sir

[@imtiyazsiddique8456]

Good

[@abigrwl]

Your video is good. 👍🏻 Last week I went for the same sort of fix. Mechanic asked me to arrange needle and float. But problem wahin ki wahin change karne ke baad bhi.

[@abigrwl]

Mechanic ne bola carborator hi change hoga. 😂🙏🏻

[@SAIREPAIR]

@@abigrwl needle change hoti hai agar uski rubber tip wear off ho jaye or ye kafi rare cases mai hota hai unless koi rubber tip ko clean karte time hi damage karde , float chamber bhi rarely puncher hote hai magar inki company fitted setting jarur kai bar kharab ho jati hai lekin vo bhi agar koi isse open ya install karte same appne apphi bend karde to , mostly overflow kachre ki bajha se hi hota hai jo ya to needle seat par laga hota hai ya needle rubber tip pe

[@salethaim7794]

same here

[@piyushagnihotri3344]

​@@SAIREPAIR 😊

[@Dj_R_zone]

​@@SAIREPAIR carborater change kar liya But problem fix nii hua Bajaj showroom se carborater purchase Kiya

[@hemeshnaik4842]

Yamaha FZ 2014 model petrol overflow problem is there but float pin is not available in my city I asd many showrooms and dealers can't find the float pin can you suggest me d alternate solution....to get rid out of this problem ...

[@SAIREPAIR]

if you sure that the float pin rubber tip is wear off then you have to replace it , if you are not able to find the replacement then you can try the float pin of other models similar to your motorcycle or search for a scraped or faulty carburetor to get what you desire

[@ueminem]

Aur same problem in pulsar 150 ug3 2007 model.thanks . Side stand mein overflow hora😎

[@SAIREPAIR]

koi bhi motorcycle ho uske liye aapko carburetor open karke hi float needle ya float ko check karke pata chalega ki kya problem hai

[@ueminem]

Float needle or. Float change kardiya. Problem solved. Thanks😀😀❤️🙏

[@SAIREPAIR]

@@ueminem you're welcome

[@anasofficialx]

​@@ueminemkitna rupya laga bhai

[@ueminem]

@@anasofficialx 300 rupay ki needle aati hai

[@LakshayMatharu]

Speed missing problem hai kis wjh se ho skti h?? Carburetor bhi saaf krwa liya hai (pulsar 150 dtsi old model)

[@SAIREPAIR]

spark plug, ignition coil , pickup coil , agar sab theek hai to phir CDI mai hi dikat ho sakti hai

[@newway365]

Sr Activa se bhi standing me petrol flow hua tha mera wo kya reason hoga .. mechanic ne kuch thik nhi btya...pls reply

[@SAIREPAIR]

sir chahe motorcycle ho chahe scooter ho jisme bhi carburetor laga hoga unsab mai problem ko check karne ka tarika or uska solution is video ko dekh ke kiya ja sakta hai, jada tar float needle ya uski seat pe kachra lag jata hai jiski bajha se overflow ki problem aati hai

[@vaibhavkulshrestha7253]

Bhai mere pulsar 2004 model ka CDi to carb connector kaplastic part toot gya hai Who lag nahi rha hai na naya milrha what to do

[@SAIREPAIR]

aap chahe to uspe dhaga lapetkar tika sakte hai, nahi to kisi scrap bale ke pass dhundlo ya garage bale ke pass , kissi bhi purani motorcycle se nikal ke laga do

[@karthik-qe8ml]

Corborater changed bro after that it's still leaking wt to do

[@SAIREPAIR]

if it starts leaking right after installation then fault in carb , if if start leaking after a day or two then there will we rust in your petrol tank , check and clean it then clean the carb

[@perfectlyrics7729]

I have pulsar 180 2013 model i recently changed my bike's carburettor because of overflow problem now bike is 🚀 😂

[@raghavan547]

Price of caruburetor?

[@perfectlyrics7729]

@@raghavan547 2300rs bro

[@munanbutt1726]

Bhai maine aaj he needle change ki thi but abi b petrol leak horha ha plzz bataye bhai ki kya krna chaheye

[@SAIREPAIR]

petrol inlet jaha pe needle bathti hai us jagha ko ache se saf karo, or float pe jaha needle lagti hai baha jo steel plate hai usse bhi thoda adjust kar sakte hai

[@abul3045]

Sir wo screw gam hogaya h khul nhi rha kya karen...?solution

[@SAIREPAIR]

impact driver ka use kare ya wd 40 spray karke try kare

[@amrutheshvijayan6265]

Bro Yamaha ray zr petrol inside air filter box

[@SAIREPAIR]

check for blockage in breather pipe or overflow pipe

[@amrutheshvijayan6265]

@@SAIREPAIR bro all this after a service i have done carburettor cleaning

[@amrutheshvijayan6265]

@@SAIREPAIR now the power is more and the mileage is just 26kmpl

[@SAIREPAIR]

@@amrutheshvijayan6265 set the air/petrol mixture screw properly for better mileage

[@Maestrotoy]

This video is Incomplete, how was before repair?

[@SAIREPAIR]

watch carefully from the start , already showed right when the petcock nob turned ON petrol started overflowing from the drain pipe at the bottom of float chamber

[@brokedvibes8012]

Bhai meri pulsar UG4 hai 2010 model, vo 5 saal se Khadi thi, fir mene uske half engine ka kaam kiya hai, lekin vo over ress hoti hai, gear shift karte time jab clutch dabata hoo to Pehle 2 second ress hoke fir kam hoti hai, kya problem ho sakta hai?? plz batao

[@SAIREPAIR]

pehle ek bar air/fuel mixture setting kar ke dekh lo agar sahi nahi hota hai to phir timing or tappet check kare

[@Shaurya_Rajput_01]

Sir ji meri scooty me chalane par carburettor se petrol leak hota hai or jab band khadi rehti hai to nhi hota mene thode din pehle hi mene naya carburettor dalwaya hai kya problem hai pls bataiye

[@SAIREPAIR]

fitting sahi se nahi hui hogi ya kissi or modle ka carb laga diya hoga , bese chalne pe siraf tabhi ye problem ayegi agar throttle bohot tight ho , ya breather pipe choke ho

[@Shaurya_Rajput_01]

@@SAIREPAIR throttle ka matalab

[@amitchaudhary8601]

Flute 1 ,2 yrs me kharab ho Jata Hai kya.

[@SAIREPAIR]

nahi

[@Rehaan_.]

Sirji maine bike 2 din pehle side stand lga kr khadi ki thi pular 150 . Kal Rath se khud se petrol leak horha h carburettor se. Kya problem ho skta h ?.

[@SAIREPAIR]

agaar side stand lagane ke bad bike normal tilt hai to video mai jese bataya hai bese follow karke float pin clean karo or agaar bike jada tilt hai to phir side stand sahi karbao

[@Rehaan_.]

@@SAIREPAIR thanks for your reply

[@rohanvpatil]

Sir meri pulsar side stand par lagane ke baad thodi der tak petrol leak hota hai aur baad mai ruk jata hai...side stand par bike jara si bhi hilayi toh petrol wapas leak hota hai...kya problem hoga??

[@Rehaan_.]

@@rohanvpatil corporator clean krvao

[@dipankarbaruah7194]

petrol AIR CLEANER me jama ho raha hai mera.. overflow nhi dikha raha hai

[@SAIREPAIR]

sabse pehl to overflow ke point ke pass ek drain screw hota hi use open karke check kare ki petrol nikal raha hai ya nahi , agar nahi nikle to drain pipe ko clean kare or agaar nikal raha hai to phir aapko carburetor pe petrol inlet se opposite side ek breather pipe dikhegi use clean karna hoga ye problem carburetor mai vacuum create hone ki bajha se hoti hai , jab carburetor mai proper atmospheric pressure na mile to petrol jada ana shuru ho jada hai or vo overflow hoke air filter bali side chala jhata hai

[@mananpatel9635]

Bhai meri bike tilt karte ho 45 degree tab carburettor overflow ho jata hai, sidhi khadi rakho tab nahi hota, it is normal??

[@SAIREPAIR]

yes jada till karne se bhi overflow problem aati hai

[@kapilchoubey3493]

Bhai agar ye pin kharab h too ye mil jayegi ya nahi?

[@SAIREPAIR]

mil jati hai

[@saurabhkesarwani9655]

bhai mere bike me bhi yahi same problem hai maine pichle saal curburetor bhi change kara ke naya lagaywaya tha to uss time sahi ho gya tha lekin abhi phir petrol leak hora wahi se toh service centre waalo ne kaha ki bike ke tank me jung lg gya hai aur wo jung gir ke curburetor me chala jata ha jiske wajah se ye overflow hota ......unhone solution bataya hai ki new tank lagwa lo nhiii to curburetor har 4 5 mahine me kharab hota rahega......... kya wo sahi keh re?????

[@SAIREPAIR]

carurator to kharab nahi hoga , lekin overflow ke sath or problems ho sakti hai , agar rust bahut jada hai to tank replace kare or agar rust jada nahi hai to rust rokne ke liye ek alag se filter petrol petcock ke pass laga de

[@aneeshmaury]

Flote niddle kitne ka hoga sir???

[@SAIREPAIR]

150 rs ke aspas

[@aneeshmaury]

@@SAIREPAIRhero honda splendor pro ka reserve kitna hota hai

[@0divyanshgour359]

Overflow ke saath gaadi start ho jayega ya nhi

[@SAIREPAIR]

agaar overflow pipe se petrol bahar nikal raha hai to bike asani se start ho jayegi , lekin agar overflow pipe jam hai to esemai overflow petrol engine mai chala jayega or bike start nahi ho payegi

[@0divyanshgour359]

@@SAIREPAIR thanks

[@harshadrathod8106]

Bro mera bike na power cutt ho jata hai chalu bike ghurr ghurr karke bndh ho jati hai fulll liver lagao to pura nahi lagta off ho jati hai aise hi whats reason

[@SAIREPAIR]

carburetor ko clean karo or specially mixture screw hole ko , pilot jet ko or pilot jet ke air inlet hole ya jet ko , video already channel pe hai dekh lo

[@laxmilepcha5664]

I tried everything sir but in my bike it didn't work

[@SAIREPAIR]

you might need to do float setting

[@amitchaudhary8601]

Bhai Mera pulsar 125 me pickup missing ho raha mechanic bol raha flute problem Hai 800 rs lagea kya karu Kara lu. Showroom me to carburetor change ko bol raha.

[@SAIREPAIR]

check kiya kya mech ne ki float puncher hai ??

[@amitchaudhary8601]

@@SAIREPAIR nhi Kiya Tha aaj fir cheque karye fluid thik Tha fluid pin kharab Hai oil continue gir raha tha pin change nhi Kiya usme packing De diya pin change nhi Kiya bola aab problem nhi hoga pin local market me nhi milta Hai koi problem to fir se nhi hoga.

[@SAIREPAIR]

@@amitchaudhary8601 pin mil jati hai

[@Aryangujar0091]

Sir bahar shop par kitna kharcha ayega

[@SAIREPAIR]

depend karta hai 50 se 100 rs ya jada bhi

[@Aryangujar0091]

@@SAIREPAIR thank you so much sir

[@anuj3859]

Kya overflow hone pr gadi band ho jati hai?

[@SAIREPAIR]

ji chalte chalte to nahi lekin starting mai dikat aati hai , bo bhi tab jab overflow petrol bahar na girke engine mai chala jaye

[@Pau7L]

Iska kitna charge krta hai mechanic

[@SAIREPAIR]

100 se 200 to aram se le lega , baki depend karta hai area or kitna kam hua hoga part pai

[@YT_sanif]

Bhai i changed my fluid pin but still same issue , mechanic kah rha carburatoretor change kro

[@SAIREPAIR]

float pin ki seat ache se clean ki thi??, petrol tank mai rust to nahi hai na ?? , agar sab theek hai to float ki setting karke dekh le ek bar

[@YT_sanif]

@@SAIREPAIR haan bhai , pr halka rust hai sayad float tank me , setting kaise kre ?

[@YT_sanif]

@@SAIREPAIR agr bhai maine naya carburetor le lia aur tank me rust hai to same issue ayega ?

[@SAIREPAIR]

@@YT_sanif ji bilkul lekin kuch time bad

[@YT_sanif]

@@SAIREPAIR bhai tank me jo rust laga hua hai use kaise sahi kre ?

[@pratikksawant8767]

Carburetor ka float movement nahi kar raha

[@SAIREPAIR]

ya to fitting sahi se nahi hui hogi, ya fir float pin float ke sath chipak gayi hogi , agar float needle jaha lagti hai vaha steel holder laga hai float needle ko hold karne ke liye to use check kare ki vo jada tedha to nahi ho gaya

[@ahmer6167]

UHU se block kerdein tu?

[@SAIREPAIR]

please write clearly , what you want to ask

[@gauravthamke5455]

Bhai maine bajaj ka new genuine carburettor lgaya hai.phir bhi overflow ho rha hai.solution btao plz

[@SAIREPAIR]

side stand jada bend to nahi hai ?? , agar normal hai phir bhi problem hai to petrol tank check karo usmai rust to nahi lagi hai

[@gauravthamke5455]

@@SAIREPAIR petrol filter lgaya ab.phir bhi thoda thoda lick ho rha hai

[@SAIREPAIR]

@@gauravthamke5455 janab to filter lagane ke bad ek bar carburetor ki float pin ki seat or passage ko bhi clean kariye

[@gauravthamke5455]

@@SAIREPAIR bhaiyaji wo sab clean krne ke baad hi filter lgaya hai

[@SAIREPAIR]

@@gauravthamke5455 hmm phir to esa nahi hona chahiye , carb ke flot ki setting karbo kisi ache mechanic se phir

[@mannannohria3079]

How much will this repair job cost ?

[@SAIREPAIR]

depend on area where you live , plus what the mechanic do , if cleaned the carb then at least 150 to 200

[@mannannohria3079]

@@SAIREPAIR thank you

[@cardcoustam6307]

24 ka mileage de raha

[@YT_sanif]

Same bro

[@Aryangujar0091]

Aur sir meri kick nikal gai hai bajaj pulsar 150

[@SAIREPAIR]

just kick hi nikali hai to bo 200 se 250 rs mai milegi or agar kick shaft mai koi problem hui to jada kharcha hoga kyuki clutch cover open hoga

[@Aryangujar0091]

@@SAIREPAIR sir ek nutt loose hai

[@SAIREPAIR]

@@Aryangujar0091 to tight kar lo

[@Aryangujar0091]

@@SAIREPAIR sir phir nikl jati hai tight krke dek lia

[@SAIREPAIR]

@@Aryangujar0091 to replace kar lo

[@shahsushameem1892]

Thanks bro