How to fix CVT transmission code p1778 or P1777

[@karolyhacs6923]

Used your walkthrough to replace the stepper motor on my 2012 Mitsubishi Outlander. I appreciate the details you mentioned. I freaked out a bit when you said not to move the actuator, that it needed to stay where it was for replacement. My actuator moved and I could not get it to stay in place, but saw in another video that there is a little hole going through the unit and you can use a small Allen wrench to hold it in place…that little detail saved my bacon. Thanks again for the walkthrough, gave me the confidence to give it a go and save $4,500!!

[@_lost_2758]

Do you by any chance remember that video

[@danielraphael8214]

@@_lost_2758using the pin hole does not work

[@mombux]

did it work?

[@danielraphael8214]

@@mombux Yes, Actually using the pinhole worked!

[@mombux]

@@danielraphael8214 and how about your car? did it fix the problem?

[@matthewbradly1816]

Ive got the p1778 code. I am going to try this. Thank you so much. You are doing the lords work.

[@TheTruelakersfan]

How many dirty mechanics would have told you that needed a new transmission and charged you for it and only replaced this piece. Appreciate your honest mechanics .

[@notalano]

This is only best case scenario, can have multiple valve body codes + damage to cvt. Not always a fix. If you have to do labor+parts a lot of shops actually end up saving their customer money by replacing with something they can guarantee is a fix for them. How mad would a customer be if you told them they have to pay for this valve body job and still need a new trans because they damaged it at some point before bringing it to your shop? Of course there are in depth diagnostics and tests and you can gather with a number of variables the cvt SHOULD still be good but I’ve done these with whole new valve body replacements and seem perfect for 30-40min of driving……then still had to replace CVT. Bigger picture

[@TheTruelakersfan]

@@notalano then you shouldn’t be a mechanic if you can’t figure out what the problem is. “Even bigger picture”

[@bernaroorodriguez6621]

Thanks my friend very very vidrio

[@SusieHaze]

Four!! And they wnated to charge me $10k for the part and $5k for the work. I tried selling my 2009 lancer to mechanics and they only offered me $300-800 saying it’s a very hard fix and my car isn’t not worth over $1000!

[@dennismelville7532]

Dirty?? This mofo didn't even have the proper sockets to remove the bolts. I cringed watching him pull that 14mm with the open end side of the wrench. Honestly, these trannys are a POS... and lack of filter/fluid changes is there biggest down fall. He got lucky with just the "stepper motor"... not all are saved with this try.

[@edsoncardoso4248]

Cléber fiquei surpreso com os anúncios em português enquanto assistia o vídeo rsrsrs, e esse foi o único vídeo que encotrei sobre essa problema… valeu pelo vídeo bom trabalho boa sorte aí.

[@cleberonegociantedaamerica]

Muito obrigado Que Deus te abençoe

[@reliquary1267]

Thanks. Wanted your opinion on this. Replaced a Nissan CVT with a used 50k mile one. Ran great for 7 months. Just had a valve cover and PCV valve replaced. Got the car back and P1778 is throwing intermittently. Had to floor the throttle from a dead stop on one occassion. Could something electrical have been disturbed during the valve cover removal process?

[@mobileoncue1370]

Very doubtful. How often do you change the CVT fluid, check the filters, clean the magnets?

[@nigellbk]

Great video man i have to do that on a 2010 Murano have you done that before and did you make a video when you did i would like to see that video

[@GDMCBJAMMIN]

Do you need a torq for anything on this process?

[@joaovictorpereirafernandes1078]

Tu mora em qual estado aqui em usa ? Acho que meu Nissan versa hatchback 1.8 cvt tá com o msm problema

[@ocruz380]

The audio cuts out when you're explaining how you know the step motor is good. I actually wanted to hear the what you said.

[@helderyoung848]

Code brot

[@rigopaz9494]

kzbin.info/www/bejne/hKPWiXuKpNaVe68 Altima but still the same process

[@brighambaker3381]

Same

[@pacojoven7854]

I knew when the audio cut whatever he was saying was some cold Bullsh*t There is no way to tell if the motor is 100% good. you can apply battery power to the step motor through power probe or jumping wires but even then you still wouldn’t know 100%

[@FloridaMan7337]

@@pacojoven7854 Yes motors can have voltage applied and run but fail under a load.

[@sandycastles7105]

12:13 no audio Q. How you know replacement part is good??

[@nubiasilveira353]

Vc está na área de Boston ou Worcester? Obrigado 🙏🏻

[@kurtgood2914]

I had to replace the valve body and its at transmission shop, but sdme problem and thanks for sharing this video

[@tajhealthnature8570]

Thanks i have a 2010 Nissan sentra. Code 1777 came 🆙.. steppa motor. You think i should just change the fluid r just change the motor.. An also. Did you use back the same fluid.. That you

[@jonathanrobles4338]

great video bro , thanks man

[@johnnyfowler2995]

Replaced my valve body in my 09 murano sl. Now I have no throttle response. Any help or tips ?

[@ernestomoreno2596]

I have a 2008 Nissan Sentra and through code p1777 and p0845?? Do you think is the same issues?

[@kanibis420]

do you know if this is the same Transmission and procedure for 2011 Nissan Rogue .

[@DarkNeosX]

Hey, dude where are you locate and how much would you charge?

[@jonidimeri1578]

P1778 and p0868 Nissan Versa 09 1.8 SL, just bought this car and give me 2 codes, trouble accelerating and slipping. Checked the fluid and looks clean and i'm affraid that this is done before because i see fresh silicone underneath this pan but i didnt touch that yet. Any advice? For replace transmission is gonna cost me $4500-5000 and its a lot! 😢😢

[@mobileoncue1370]

Hi Jon, dealing with similar issues on 2010 Cube (same CVT). Have done lots of research and changed trans pan, fluid, filters, tested solenoids, cleaned valvebody, etc. No resolution yet but I'm checking the readings on the temp/pres sensors now. Codes are: P1778 (step motor), P0746 (sol.A), P0868 (low pressure). This car has 160k km and looked like the fluid was original (never changed, black). :/

[@jonidimeri1578]

@@mobileoncue1370 Dropped on the shop yesterday, hope tomorrow i'll get a response from mechanic! The problem is these cvt no one repair or rebulit, replace only and this is so expensive and im down already $6k and is high possibilty to junk the car , it not worth to spend 5k more on the tranny on this car. The lowest estimate i've got was $4200. Unfortunately what i asked, these are death codes and need a trans replaced and i don't have any hopes honeslty.

[@Sunxmoom_]

hey man is this car the one you are fixing use same Trany then Nissan cube 2009, i have codes P1778 and P1421 thanks i hope you see my question...

[@NoName-oy2km]

Thankyou for making this. I will give it a shot.

[@mthokozisimnguni3745]

Hy please help I bought Nissan Maxima it's have a problem to change gear no 4 is Delayed to pick And some times it forst you to pull over and which of some second then started again then change gear smooth what a cause

[@josefranciscoesquertalaman3827]

Presente cordial saludo desde Navoyork Sonora México Like

[@steve-ip1cd]

Do you have to have the transmission reprogrammed after replacement of the stepper motor?

[@alhavana9426]

Yess your supposed to, but I guess these idiots don't know that

[@hilarymullings6280]

Thanks for this video did you experience any slipping both in drive and reverse before the step motor was replaced

[@ehiztechgadgets9ja]

Please help, my Nissan altima 2008 2.5s stocked up in first gear, won't go beyond that, after diagnosed with computer, P1777 code was detected, today I took it to my mechanic, he service the gear, and test drive, it worked, after few seconds, when the car warmed up, it got stocked in first gear again. Now I noticed That ATF fluid was used to top up the gear oil instead of CVT fluid.. Please I need your help, what should I do?

[@algburi4403]

where are you located man? hopefully around phoenix az. i need this service for my 2012 kia optima hybrid w/ code P1777. thank you

[@aqn1976]

I have a 2015 Sentra and I'm not sure these are the codes because my mechanic just said I probably need a new transmission but the issue with my car is that it jerks from 2nd->3rd gear and also jerks a bit when putting it into reverse. So are these the signs for the codes you mentioned in this video???

[@cleberonegociantedaamerica]

On my car don’t shift the gears

[@cleberonegociantedaamerica]

Try to do the transmission service on your car maybe help you Change the oil and filter

[@aqn1976]

@@cleberonegociantedaamerica My mechanic says will need a new tranny but new trannys are hit or miss regardless if they're from the deale..sadly it turns out that this is a common problem with 2015 Sentras that there is close to being a class action lawsuit bc of so many cases :-///

[@marcovivanco586]

I have that code in my Nissan Quest 2013 , can I do that in my car and is the same locación .. what is the name of the small part that you have removed.. thank you for you video..

[@cleberonegociantedaamerica]

I never do it on Nissan Quest but you can tried the name of it is step motor

[@DavidAbella]

How did you scann the code , whit a normal obd2 or special transmission scanner? thank you.

[@nubiasilveira353]

Quanto custa um serviço desse ? E onde é sua oficina? É em Massachusetts? Valeu irmão!

[@dinomakwakwa875]

Hi cleber my 2008 outlander is not is stuck on gear 1 is not changing.is it the stepper motor?

[@nononsensegalnononsensegal4967]

I have 2007 Nissan murano with a p1777. I would like to know does the transmission valve body cvt3 does it needs to be reprogrammed before its place in my vehicle ?

[@cleberonegociantedaamerica]

Yes but some cars when you replace the transmission valve body it will need to be reprogram

[@deangelosmith231]

How you do that?

[@viviennebutmakeitanime9807]

My Nissan cube won't move, when I put it in park and floor it the car revs up and down is this what's causing it?

[@_papa._popa._71]

Thanks for the amazing video bro ,Hey man I’d love if you can get back with me ASAP I actually have a few questions i had the p1778 code which cased my car to not accelerate over like 20mph and it’ll like bump a little like I ran over something so I followed all the instructions I changed the step motor even with putting in the allen ranch in pre drilled hole but afterwards when I got done it wouldn’t shift gears it wouldn’t move at all and I removed the valve body up and respected the process and it still wouldn’t shift , do you think the step motor they sent me may just be bad? Or do I need to make sure every bolt is on before removing the Allen ranch ? And how do you find out which bolt goes where I didn’t keep up and number them but I’m shake to get all screwed in idk if the right one is going in but it’s fitting

[@rgcd5043]

I got the same problem with a Nissan

[@_papa._popa._71]

@@rgcd5043 make sure u have enough fluid in the transmission and I’d say let it sit there for abt 3 days or so before u try to move it ig so the computer can catch up with the valve body u unplugged and put back in Bc after a couple days my car finally shift gears again

[@k.j.w5205]

@@_papa._popa._71 To avoid that problem, it's probably a good idea to disconnect the batter before doing the job to avoid the computer issue

[@tueslirazan]

@@rgcd5043 I have the same problem with nissan too

[@soundarrajsanthanaraman3993]

I got the same problem with my Nissan murano, i replaced with new transmission, tried with multiple new stepper motor, oil pressure sensor , still getting the 1778 error code and at higher speeds feel it is still bumpy. replaced the entire transmission oil as well, new filter etc. any suggestions?

[@dfishnmtmartin6864]

How do you know it’s good? The sound cuts out right there for me...thank you! Got to do this on my 2013 murano...great video just need to know how to get one and know it’s good? Thanks!

[@lorenacastillo4511]

Hi saw comment and now my 2014 is doing this did it fix yours

[@zeusss6222]

Same here, I own a 2013 murano and it’s doing the same thing. Got the same code. Don’t know if I need the whole transmission or just this part.

[@cleberonegociantedaamerica]

Sorry I have to take the audio because I have music on The back sorry

[@brandongrover3974]

@@cleberonegociantedaamerica but how do you know the stepper motor is good that’s why I need to know

[@roostr5003]

Don’t buy a used one it’s better to buy a new step motor on eBay or Amazon

[@LS-ti1rz]

Tengo la misma code con mi 2014 Mitsubishi Lancer. Es el mismo para heglar?

[@cleberonegociantedaamerica]

Primo yo no yso uno Mitsubishi pero intenta lo a ver primeiro dios que te saiga biem

[@marvinj222]

Hola, tengo una Pathfinder 2014 con el código P1778, le acaba de cambiar el aceite NS3 y el filtro de elemento, pero a bajas RPM se siente como pequeños "jalones", tiene 72 Kilometros, cuando saque el aceite solo tenía como 2 cuartos, y antes del cambio los "jalones" eran mas fuertes.

[@cleberonegociantedaamerica]

Mira yo creo que los solenóides no te trabaja biem porque quedo com trabajando com poco aceite

[@marvinj222]

entonces lo ideal es cambiar el cuerpo valvular, o se consigue solo los selenóides?

[@marvinj222]

sabe el numero de parte del step motor de la pathfinder 2014?

[@roostr5003]

@@marvinj222 compra los solenoides sueltos en mercado libre o Amazon y se los cambias es el mismo proceso que cambiar el step motor

[@marvinj222]

@@roostr5003 cuantos selenoides son?

[@mercurialmystic]

once you put it back together, how do you refill it with transmission fluid?

[@cleberonegociantedaamerica]

I don’t remember because it’s long time ago so just go on Google and ask for transmission drain so they will let you know what is the amount

[@seangyimah]

Car still fine ?

[@ramongarcia6939]

I replaced the step motor and a week later it gave me the same code do I need to replace the hole part now? What do you think? The step motor was new when I bought it

[@cleberonegociantedaamerica]

Did you feel that the cars is driving better than before you change the step motor?

[@antonioalvarez7326]

I have same code on Nissan Quest 2014 would that be the same problem?

[@geemoney6014]

Trabajara esto en in 2012 Nissan Altima 2.5 ? Tengo El mismo codigo p1778 de El step motor

[@cleberonegociantedaamerica]

Se trae el mismo code sim tenes que trabajar

[@JorgeHernandez-xj9sc]

hermano yo tengo una Nissan Rugue 2011 y tiene el mismo problema estoy viendo el video y cree que sea la misma pieza que le falla a mi troca de antemano muchas gracias si me responde buen día

[@cleberonegociantedaamerica]

A lá orde primo

[@yordanardon4374]

Hola jorge tengo un rogue con ese codigo me puede desir como le fue con su carro que iso que le cambio o se arruino

[@reinnycapellan7795]

Hi where you r I have 2012 Nissan Sentra o have p 1778

[@DJXTACY2012]

How did you diagnose the code if it was not showing a check engine light ?

[@cleberonegociantedaamerica]

It don’t have no code and check engine light it’s your transmission clutch going bad

[@chrismensinger9261]

What does it mean when you have both a p0868 and p1778 on a 2011 nissan murano?

[@jonidimeri1578]

Did you figure out? Same codes here nissan versa sl 1.9 2009

[@endrewssilva2644]

fala brother, eu tenho um Nissan 2009 rogue q ta com o mesmo codigo, seria a mesma peca? abraco de Nova iorque.

[@cleberonegociantedaamerica]

Na verdade eu não fiz na Nissan Rogue até hoje

[@beyenetekle8429]

Do you know a mechanic in Georgia who can solve P1777 infiniti jx 35

[@cleberonegociantedaamerica]

I don’t sorry Please subscribe Thanks

[@Cruz0604]

Hey so my Nissan Murano was working excellent but then the battery died when I left the switch on. I jumps start it and now the car is running but the the RPMs stay high and to reach 60mph it’s up to like 5,000 RPMs there are 3 codes P01778, P0840 and P0845. Any experience on this ?

[@mcafeemarcellus1415]

Mines is doing the same I just bought it . have you got yours looked it to see what the problem is yet?

[@jasonjason622]

@@mcafeemarcellus1415 mine started it too. what was the fix?

[@Subdevil1129]

Any updates?

[@NickStokes69]

How did you know it was good? Mine is out and needs to be changed, but all the stepper motors I have seen online are used and idk how much mileage is on them and if they are any good either, so how can I find out if it’s good.

[@cleberonegociantedaamerica]

on ebay you can get one

[@brendasalvador2189]

hi, i have a question. i have a 2010 nissan altima and i have the code p1778. will this procedure fix the problem in a 2010 nissan altima?

[@cleberonegociantedaamerica]

If your transmission clutch still good yes it will works

[@LS-ti1rz]

Mi hermano espero que el solenoid o el step motor de el Mitsubishe Lancer 2014 cera mas facil para sacar? Ojala?

[@cleberonegociantedaamerica]

Ojala

[@leonytigre]

What is the part number I need it for my 2011 versa thanks

[@yaitehernandez7677]

Where do you live??? I have this problem

[@kingmike1580]

Would this work on a 2013 nissan rogue

[@kingdon9690]

My transmission pan has metal shavings all over the magnets is that a bad sign that the transmission is shot? I have this code, and same symptoms.

[@cleberonegociantedaamerica]

Yes it’s a bad signal

[@ramplaartesmarciales4918]

Que tal, antes que nada gracias por tu gran video, tengo Juke 2012 y tengo el code p1778, muy seguido avanza muy lento solo se revoluciona pero acelera muy lento, en ocasiones todo perfecto, cambiando este selenoide debería trabajar, algo mas ya esta dañado?, antes de esto en la marcha se subian las revouciones solo y bajaban como si la banda se soltara. Gracias!!!!

[@cleberonegociantedaamerica]

Primo yo no hablo muy biem Spanish pero voz ya miro se tu azeite e lo filtro está em Buenas condiciones e tenes muchos carros que sale este mismo código mas lá transmission ya está mala de adentro porque adentro trae una faja e quando no lo da el mantenimiento em lá transmission está faja se astira e por esso as vez el carro ya no trae fuersa para aranca

[@elcompaalfredo3229]

Que tal si pudo arreglar su carro lo mismo pasa con mi carro que usted hiso

[@ramplaartesmarciales4918]

Hice cambio de aceite y el problema se quito en un 90%, cambie filtros tambien.

[@ceciliabrown442]

Where are you located at? Like to bring my car

[@cleberonegociantedaamerica]

I’m in Laurel Maryland

[@totalviolation]

@@cleberonegociantedaamerica how much you charge for transmission control solenoid?

[@brantnc]

@@cleberonegociantedaamerica what's address or phone. Sending everyone to you

[@guillermorodriguez4228]

@@cleberonegociantedaamerica y si te quedo bien la trasmisión por que yo le cambie el step motor ami trasmisión y siguió asiendo lo mismo

[@Likesupercars]

@@cleberonegociantedaamerica Hello what's the Location please

[@crystall3144]

Do you have to reprogram the transmission after you replace the step motor?

[@klaidenmorad103]

No.He just said that don't need reprogramming

[@lorenacastillo4511]

I saw your video where is your shop

[@joshuarbanda]

I have a 09 Nissan Altima 2.5L . How many quarts of oil did you put back into the car.

[@Matar_Al-Tabari]

Hi dear. I have 2010 Altima 2.5L and it needs 5 Liters of CVT fluid. But next generation 2013 needs 4 liters only FYI. I replaced it many times during 6 years. In the latest one I used the new version NS3 instead of NS2 and no problem with that. Also keep in mind to clean the metal filter (cleaning is enough) and replace the cooler filter. Only with cooler filter replacing you will feel a big difference and get smooth performance.

[@cleberonegociantedaamerica]

Depends what type of service you gonna do on Transmission if you do drain or if you wanna do flushing it’s a different amount of oil

[@thedude8976]

@@cleberonegociantedaamerica I think you meant flushing. Flashing will get you in trouble. Lol Great video bro 👌 thank you

[@vica3451]

Is it same for 2007 nissan Maxima?

[@cleberonegociantedaamerica]

I not sure because I did it on a Sentra I don’t want to tell you something that I don’t know

[@bootman589]

If i replace valve body does it have to be program to car

[@cleberonegociantedaamerica]

Yes

[@bootman589]

@@cleberonegociantedaamerica what wrong I nissan

[@JoseRamos-il9vm]

Thank you very much.you are the Mannnnn.👍👍👍

[@FoxNewsNewYork]

Nice work, but from 13:12 to 15:05 there was no sound.

[@cleberonegociantedaamerica]

Sorry it’s because the music I have on They cut off the sound

[@cleberonegociantedaamerica]

Please subscribe

[@DavidSanchez-365]

@@cleberonegociantedaamericahow do you know the step motor is good from the junkyard ? I have lancer im going to do this job this week if this doesn’t fix it I’m going to replace with a used transmission

[@AG357AG]

I’ve never seen transmission fluid look like that

[@bestmangeorge1820]

Hi, thank you for the information. Please can this work on mitsubishi lancer 2008 with the code P1777?

[@cleberonegociantedaamerica]

I’m not sure but just tried do the transmission service frist

[@khairulnahar9953]

Stepper motor problem

[@gregmeeks2753]

very good video ! thank you sir.

[@cleberonegociantedaamerica]

You are welcome

[@anthonyhenry7631]

Did this replacement fix the car?

[@cleberonegociantedaamerica]

Yes it work

[@timothyhardy7450]

I have a 2009 nissian Altima and it didn’t work for me

[@Big_AlMC]

@@timothyhardy7450 sucks to suck

[@CCCCLopez]

thanks for sharing your knowledge

[@cleberonegociantedaamerica]

You welcome

[@ralphdelvalle2955]

@@cleberonegociantedaamerica a donde tienes tu garage

[@ericheaf]

Boa. To fazendo isso agora c minha Nissan Rogue. O q vc usa p limpar o filtro? Nao achei p comprar

[@cleberonegociantedaamerica]

Vc está no Brasil ou no estados unido?

[@cleberonegociantedaamerica]

No Brasil Vc pode usa olio diesel mas depois vc deixa secar bem e aconselho vc colocar um pouco de olio novo da caixa de marcha pra limpar o resto do resido do olio diesel antes de coloca o filtro na caixa de marcha ok

[@cleberonegociantedaamerica]

Se vc estiver no Estados Unidos vc pode usar Break cleaning e deixa secar bem antes de colocar de volta na caixa de marcha ok

[@twoney]

Tenho uma Nissan murano 04, fiz a troca dessa peça .. mas o erro continua p1778.. e a troca de marcha está demorada eleva o giro muito alto....será pelo fato do filtro?

[@anafreitas4700]

Você é brasileiro? Tenho um máxima Nissan 2.5 2009 tem como saber o código sem ter esse aparelho? Saber só pelo modelo? Penso q o problema é step motor

[@k.j.w5205]

Poderia o fluido tambem. Vc precisa usar fluido CVT

[@laurastafford552]

This is exactly what I need with my Rogue, where are you located?

[@chrisschlichting9145]

I do the same work im in md

[@BMW34567]

What is that called that I can get on Amazon for my Nissan Rogue Sv 2016

[@roostr5003]

Step motor

[@Elgueroinks]

Is the 2012 the same as 2017?

[@cleberonegociantedaamerica]

All the CVT transmission

[@cleberonegociantedaamerica]

Nissan

[@dealerauctionnightmare4689]

No sound after 13:12...starts again at 15:06

[@cleberonegociantedaamerica]

It is because I have music in the back so I have to mute it sorry

[@tanismedina1353]

Hi, good afternoon. I have a 2010 nissan altima with the same code. My car starts fine and drive fine for an hour, but after i feel it starts to lose power and the car start to go slower. Sometimes i have to turn off the car for a few minutes and start the car again and it drives fine again for a few more minutes. Do you think this will solve the problem?

[@cleberonegociantedaamerica]

I have on Nissan Maxima with the same problem I just do transmission service with the filters and it work perfect

[@tanismedina1353]

I replaced the step mottor and still havr the same problem. Any tip?

[@dejesusmouton9517]

@@cleberonegociantedaamerica transmission service?

[@ElPalo.]

@@tanismedina1353 did u find the issue my friend?

[@_eddie710]

@@tanismedina1353 did you find the problem? My Nissan Altima is doing the same thing. Going to change the step motor. Hopefully it fix the problem

[@JuanDiaz-pc5cr]

Thanks MAN

[@TheMahasski]

Where are you located and is that the same for a nissan versa tranny?

[@Big_AlMC]

Yo mommas hous

[@dbriggs1689]

Thank you!

[@lyneyapple]

Hello what’s the address I have the same problem and that code come up on my 2014 Nissan max

[@anastasiolanda9729]

I have 2012 nissan rogue same code, it is the same process and problem?

[@cleberonegociantedaamerica]

I have never tried in a Nissan Rogue

[@yordanardon4374]

how did you fix your car what was the problem

[@dripboss4602]

Can it work on a 2009 Nissan Maxima I have the same code please let me know thanks wonderful video

[@cleberonegociantedaamerica]

If you have CVT Transmission and the same code it will work for you to

[@brandonbaker8584]

The man. Thank you so much. Saved my family alot of money. Bless you

[@gibson7654]

Replaced the motor with new and the P1778 code came back. What could it be?

[@crand20033]

Could be time to buy another car. These tranny's are not designed to be worked on anyway.

[@officialdezyherbeauty1993]

What is the name of the big part you remove where the step motor is

[@cleberonegociantedaamerica]

Transmission valve body

[@cleberonegociantedaamerica]

Step Motor is the small part I place on the valve body

[@dayton214]

@@cleberonegociantedaamerica muy buen video y muy claro gracias. una pregunta,,,,,tengo una rogue 2013 con el codigo p1778 el problema es que no acelera,,,y como que se jalonea...y en reversa aveses jala vien y aveces no,,, solo ese codigo aparece,,,,,gracias,

[@ramplaartesmarciales4918]

@@dayton214 has logrado corregir el problema? gracias

[@XqeDiosxqe]

Cuando explicabas la mejor parte se corto el audio.......me quede sin saber.

[@cleberonegociantedaamerica]

Ess porque tenia música e tuvo que quita el áudio

[@teebaby9884]

I HAVE THE CODE P1777 ON MY 2009 NISSAN MURANO SL... I JUST RECIEVED THE STEPMOTOR FROM AMAZON. FROM LOOKIN AT THE COMMENTS. I HOPE THIS FIX THE ISSUE

[@albarivera420]

Hi. My show same code too p1777 07 nissan murano did u fix urs ? I trying order it to in amazon too

[@dagoddezzklawzz]

Hi I’m having the same issue with my rogue rn but my speed can go up to 80 mph and then it drops between 40-60 mph. I wanted to know if the part was good from Amazon?

[@teebaby9884]

@@dagoddezzklawzz girl i still havnt installed yet but go on amazon to look at the reviews

[@carolinerica3720]

will this work on 2009 nissan cube?

[@cleberonegociantedaamerica]

If your car have the same problem

[@gibson7654]

You cut the sound at the point you were explaining why you think the step motor was good, which is what I needed to know. Care to explain, please?

[@roostr5003]

Use a multimeter to test the step motor if is good or plug it with electric source to test the step motor should move back and forth if it works just fine

[@ttautogarages]

thank you

[@joshuarbanda]

I switched the stepper motor about a week and half ago and the p1778 code popped back up I followed everything in your video. I also have a P0420 can that affect the P1778 code

[@cleberonegociantedaamerica]

Hi

[@cleberonegociantedaamerica]

The code PO420 means that the vehicle control module has detected that the three-way catalytic converter is not working probably

[@rubiojunior98]

como cusnto cuestan los sensores

[@SuperJjhowell]

Your audio needs to be way better! You should instruct every step of the way. Also consider putting your step-by-step dialogue in the body content of

[@videoslucha3000]

es el velocimetro bro?

[@cleberonegociantedaamerica]

No el problema Es el step motor de la transmission

[@molaroismorais1955]

Cool

[@marcelocortes1632]

Como se llama la parte ?

[@j.d.garcia2757]

@marcelo Cortes1632 La parte se llama Stepper motor 😊

[@JPtheGamer650]

Can I get someone’s opinion? So my Nissan Sentra has the exact same issue, I went ahead and bought the step motor, even bought a new transmission oil filter and gasket, and 4 quarts of CVT fluid. I would have done the work myself, but honestly, my fat ass didn’t wanna have to squeeze under there nor did I want to deal with the mess of draining the pan. Anyway, so the shop I took it too, initially said they can do it, and it should take about an hour or so, for about $70 bucks. Ok great, no problem. 4 hours later, they finally call me to tell me that it was a bit more “involved” than anticipated. And now they want $350 CASH for labor ONLY. Seems like a pretty straight forward job that could have been done with hand tools, but this is a freakin shop with a hydraulic lift and impact drills and such. My gut is telling me that this dude is tryna pocket the money since they wouldn’t even be losing any inventory. I should probably also mention that I only went to this place because they were highly recommended by locals on the NextDoor app, but they all mention the owner being the go-to guy. Unfortunately he’s on vacation and won’t be back for another week. This other guy is tryna hustle me, ain’t he?

[@cleberonegociantedaamerica]

If he replaced the step motor and do the transmission service filter and oil the price is not bad because it’s like 3 hours work if you know what you do

[@alexislynch2816]

@@cleberonegociantedaamerica what do I fill it back up with

[@LifewitNaee-if9vi]

@@alexislynch2816cnt transmission fluid

[@brandon701252k]

Man i wish you was in new Orleans

[@Dewayne-v4r]

What happened to the audio

[@cleberonegociantedaamerica]

They cut off because the music on the back

[@seangyimah]

I think I did the bottom valve wrong

[@seangyimah]

Like the part with the 14mm screw