How to Fix Non-Customer Mode Error in Xerox WorkCentre?

How to Fix Non-Customer Mode in Xerox WorkCentre. In this video, I will be demonstrating how I fixed the Non Customer Mode issue on Xerox Workcentre. Also will be showing how to replace the Fiery Board RAM Battery also known as Xerox® WorkCentre™ 7655 7665 7675 7755 7765 7775 NVM Memory Back Up Battery 960K27122 960K14440 207E22200. This was to fix the 'CCM POST failure. NVM battery may be dead' error as shown on the logs.
Relevant keywords: How to Fix Non-Customer Mode in Xerox WorkCentre, how to fix nvm battery dead issue, non customer mode error, customer mode error, unable to use xerox because of non customer mode, xerox stuck at noncustomer mode, non customer mode error block, how to remove non customer mode.
Music Credits: [FREE] TACO RAP BEAT || Hip-Hop Beat 2020 || by FING Beats.
We are doing our best to prepare the content of this site. However, we cannot warranty the expressions and suggestions of the contents, as well as its accuracy. In addition, to the extent permitted by the law, we shall not be responsible for any losses and/or damages due to the usage of the information on our website.

[@karmendimas5274]

dont need the STUPID MUSIC, talk,! use your mouth!!!!

[@TechzClubOfficial]

I wish I had a mouth 😶

[@nivekirv2039]

Is that the same procedure for the Workcentre 7775?

[@TechzClubOfficial]

Should work!

[@printyourimaginationspw8261]

Hello Sir! My wc 7535 does not go to sleep mode it stays on low power mode even after setting of sleep mode. could you please help? thanks with regards.

[@hamidbnd]

Hi. Thanks for the video. I have C8035. there is two problems. one is that when I click the sleep mode manually, it shows the following error and doesn't go to sleep mode: "a condition exists that prevents device to go to sleep" The second one is that it shows the non-customer mode error. please help to fix these problems. thanks

[@shaikhshakil91]

How to remove non battery..??? & my machine shows activation code required...wht I can do??

[@gurudevgurudev7455]

Thanks sir

[@TechzClubOfficial]

Welcome

[@MJ-rr4hd]

Hi there, I have A workcentre 7535. can I reduce toner consumption by going to the diagnostic mode and going to the adjustment section?

[@thomaswalker3157]

👍

[@shashankshekhar3453]

Copying and printing not available in Xerox 7545, what to do to resolve

[@reflexusa67]

Ok, we have a wc7855 in non-customer mode the battery has over 3 volts, what else do you think it could be???

[@reflexusa67]

i got it, this wasn't the issue, but it gave me access to what i needed to clear, reset, and reboot. Came up like a whole new machine!!

[@TechzClubOfficial]

Awesome! Cheers ✌🏼

[@nuwana2208]

My WC5875 machine is restarting when some work is doing. what may be the reason?

[@TechzClubOfficial]

I'm not sure but it could be some software issue. Maybe needs a firmware update or reset should help! Better to consult a technician.

[@nuwana2208]

@@TechzClubOfficial thanks for reply. yesterday I solved the problem by resetting the machine

[@muhammadishfaq8211]

Problem in Xerox 58xx. This machine takes around 5mints to ready for operation. Please tell me how it ready fast for operation.

[@TechzClubOfficial]

That is common... the printer had to heat up in order to melt the color powder! So it takes around 5 mins which is common!

[@JudeJakosalem]

How about SIM insertion machine not set?

[@shashankshekhar3453]

What is the life of a NVM Battery

[@mpugwa.j.mukendi4128]

what about xerox 7220 is that the same solution?

[@TechzClubOfficial]

It depends! Pls check the fault history description that could help you understand the issue better.

[@JeroenSteen]

When I unscrew the board, and pull the handle it turns on. Maybe the power needs to be completly off? Where to buy the NVM for WorkCentre 7545?

[@TechzClubOfficial]

Yes turn off the device before unscrewing! And the NVM can be bought online from Amazon.

[@JeroenSteen]

@@TechzClubOfficial How can you get the old battery out, it's pretty stuck.

[@TechzClubOfficial]

@@JeroenSteen I just used a mini screwdriver and lifted it gently from all sides.

[@JeroenSteen]

@@TechzClubOfficial I did it with my finger, and lifted it up underneath the corner with the black dot. That works as well.

[@mrsky360]

How much battery cost

[@DesignXstream]

I think it's 500/-

[@asiriindrajith7208]

I need this battery