How to fix Lenco trim tab switch and retrofitting/upgrading to the led version. You can buy the complete switch assembly here. This is all you need to upgrade to led www.amazon.com...
Пікірлер: 24
@keithbunch624 Жыл бұрын
Got it! Reworked the ground and used the purple wire ( Evinrude) for the 12v source. Thanks
@mikito054 жыл бұрын
Your video was extremely helpful. I upgraded my lenco switch and everything worked fine as you show us in your video. Thank you. I just want to point out I had to wire the orange cable to switch in order for everything to work. thanks for the video.
@loumalonephd5973 жыл бұрын
You had the basic switch and upgraded to this? Everything good?
@keithbunch624 Жыл бұрын
Thank You! Installing this today!
@justintew25432 жыл бұрын
Looks like a Parker 2x20… thanks for the video. About to do the exact same job on a 2320 and found this
@ChasingPelagics2 жыл бұрын
That’s exactly what it is 👍
@flatlander69289 ай бұрын
Those led switches don’t last, going on 3rd replacement. I’m going to the 100 dollar rocker switch. No retract, less to FAIL!
@MikeSmith-nu9wt3 жыл бұрын
mine did that , we used epoxy and fixed it , but i wanted the L.E.D lights to tell me where the tabs where
@DavidWilliams-vo1wp Жыл бұрын
What if all of your lights are flashing and alternating from left to right?
@Tomikingi4 жыл бұрын
Thanks for the video. Question: Do you have to connect the little orange wire? I didn’t see where you connected it. Thnx
@ChasingPelagics4 жыл бұрын
orange wire goes to the ignition switch. When the signal is removed it generates the auto-retract feature.
@CThomas12345 Жыл бұрын
I’m having a problem with the control box clicking. If I get the new switch I can get rid of the control box all together since it’s all in one?
@ChasingPelagics Жыл бұрын
I believe so
@slawekwrobel37864 жыл бұрын
hi i have same problem i upgrade lenco port trim tab it frozen same like on u video how do u fix it , boat its in the water
@ChasingPelagics4 жыл бұрын
you cant fix it in the water
@slawekwrobel37864 жыл бұрын
@@ChasingPelagics tank You
@keithbunch624 Жыл бұрын
Hey, I have my switch installed; I am not getting any power at all. I have it connected to the fuse block properly, (pretty basic). The fuse is good, kind of at a loss why it wont work. Thanks in advance.
@keithbunch624 Жыл бұрын
wired the orange into the 12v on, Evinrude Etec ignition switch. Used the purple/red on-off wire on the switch.
@ChasingPelagics Жыл бұрын
Check ur ground
@barrytisdale71194 жыл бұрын
Thanks for the post. I had the exact same problem with the female connector pulling off the board. The pins on mine did not stay on the board or the connector, but fell to the ground. I picked up as many as I could find, but even those I can not find. So, I wanted to reuse the switch I have which looks just like the new one you installed with the LED display. The video did not show if the new switch had the same connector as the old one or not. If it did, did it come with the the female connector installed? (and hopefully secured better)? I am just hoping someone has already come up with an easy cheap fix to get me back on the water. Thx
@ChasingPelagics4 жыл бұрын
The switch comes with the wiring harness.
@barrytisdale7119 Жыл бұрын
I know this is an old post, but I do you still have the information on the new switch or is there a link to where you bought it and part number…
@alexrodriguez23433 жыл бұрын
hello to you change the switch you removed the relay box