Great video! You're making this so much easier for people just starting out with FPV quads.
@mlit838 жыл бұрын
Thank you so much man! I've just ordered and going to build my first 250 FPV quad, .. a ZMR250. And this is good info! Thanks again!
@andreiandrosoff13279 жыл бұрын
Great video, thanks! To me, the best solution to removing the + wire would be to use a servo extension that has the red wire removed. That way you don't have to risk damaging the pin/housing on the ESC connector itself or mutilate your USB programmer by bending the middle pin.
@Broxerlol9 жыл бұрын
Thanks for making these videos. I know when I setup my quad I spent a lot of time finding information like this. Just a side note to clarify the comparison at the end, damped light is causing the motors to brake when the throttle is cut. Oneshot isn't required for that. For instance, my Rotorgeeks 12a ESC's support oneshot but not damped light, so they spin freely when the throttle is cut.
@FlightClubFPV9 жыл бұрын
Brox3r thanks for pointing that out. i learned something new :)
@billyclark55739 жыл бұрын
I like your slower and "just to review" style of instructional videos. They are easier to follow and more thorough than others. The BLHeli dampen part of you video would have been more revealing if you would have not chopped the throttle all the way off but maybe from 3/4 to 1/4 to show if there is dampening. From my understanding any throttle decrease should have dampening but I have never seen that bench tested. Chopping all the way is just showing drag brake similar to folding prop glider settings.
@KWO819 жыл бұрын
Really great Videos!!! They are a big help to me! Soon I`m getting all my ordered stuff for builing my own copter! With your videos i`m sure i`m gonna work it out! Thanks dude & fly on!!!!!
@CarlLundin9 жыл бұрын
Great video as usual! Keep em coming!
@gusf84519 жыл бұрын
when you changed the parameters in BLhelisuite shouldn't you have pressed {write setup " before you press disconnect? another question would this turngy USB linker work with Emax 12A esc? thanks
@andrewauguscik90628 жыл бұрын
will this work with the little bee 20a escs for Blheli? Thanks in advance, many of your videos are very helpful and have helped me with my build!
@davidlyw898 жыл бұрын
hi, I saw your blheli with oneshot run smoothly on start spinning the motor. I have issue here. I did everything the same but, when i arm it, few of the motors cogging before actually spin up. When I disable oneshot feature, the issue gone. Any advice? Thanks
@adolphjanssen65808 жыл бұрын
hi there, just a quick question, Is there any advantage flashing BLheli and not using oneshot. Or if you don't use oneshot you might as well not flash BLheli.
@chmnyswft40238 жыл бұрын
Great as always. Thanks man.
@selespeed39 жыл бұрын
what quad is that you are working on? seems nice
@ronnwilson23509 жыл бұрын
Nice informative video. I got a question, I was recently flashing a new Naze 32 acro board and the flashing went fine but when I tried to connect it says I need a newer version of Cleanflight configurator. I've downloaded the newer version of configurator but it acts like I haven't, still can't connect to the Naze board and still says I need a newer version of configurator. Any chance of doing a short video for doing this, it's probably something stupid I'm not doing but I would really appreciate the help. Thanks
@ronnwilson23509 жыл бұрын
I actually just figured I could erase my old Cleanflight program and then just redownload the updated version, much easier. Thanks anyway lol
@domasback9 жыл бұрын
hi, what kind of watch do you own? very nice
@thekidphi9 жыл бұрын
Thanks ! Does it work on Turnigy plush 12A ?
@michielvanwelsenaere99599 жыл бұрын
So this will also work using an arduino instead of a turnigy linker?
@michaellee50849 жыл бұрын
can i flash the esc's with them on the quads pdb ? thx
@MikeRub50018 жыл бұрын
How do you choose the amps on ESCs
@4mulas9 жыл бұрын
is solidworks needed to do this?
@chunkynugget9 жыл бұрын
What is oneshot and what makes it so great? What is clean flight and why is blheli better than simonk??
@FPVRCFlight9 жыл бұрын
Increases the rate of which that motor can spin so it makes it react faster
@andyg62799 жыл бұрын
just to save you some time when you pulled out the red wire don't do that just bend the middle pin on usb programer
@johar3579 жыл бұрын
Dont need CF. For oneshot. Im running cc3d on OP 15.02 supports oneshot just fine.
@FlightClubFPV9 жыл бұрын
johar357 Glad CC3D finally caught up!
@rtcfpv10128 жыл бұрын
+FlightClub Hi, what type of receiver works for oneshot? Thanks for sharing the video.
@tatwaili14039 жыл бұрын
Where are the links?
@FlightClubFPV9 жыл бұрын
Tat Wai Li everything is on the website. fpv-flightclub.com/cleanflight-blheli-oneshot/