How To: Garmin G3X Shielded Wiring Harness Fabrication

  Рет қаралды 6,460

Tony & Anna's RV-7 Construction Videos

Tony & Anna's RV-7 Construction Videos

Күн бұрын

Пікірлер: 13
@garryshepherd8005
@garryshepherd8005 4 жыл бұрын
Very well narrated and very timely since I am at exactly this spot on my RV 7 A project ,I just ordered my Garmin hardware yesterday,, Love to see how are you build the shelf , and radio racks to carry all the ancillary boxes and remote radios etc.
@cramersclassics
@cramersclassics 3 жыл бұрын
What timing.... I am going to replace my old non-touch G3X small screens with a G3X large touch and G5 this Fall in my RV7A. Great quality video!
@matthewkruger8417
@matthewkruger8417 2 жыл бұрын
Thank you very much. This was very helpful
@LTVoyager
@LTVoyager 2 жыл бұрын
Even the Garmin 2.5” of strip length is about the most I would want. Every inch those wires extend outside of the shield is more “antenna” to pick up noise. Ideally, you want the shield of the cable to extend into the metal back shell on the connector.
@LifeLatitudes
@LifeLatitudes 2 жыл бұрын
I like the music 👌🏻🙂
@KitfoxPilot
@KitfoxPilot 4 жыл бұрын
I just got my g3x garmin system. I am having problems finding the wiring diagrams for what pin goes where and what wire size. Started mounting the GMU 11 Magnetometer in the wing. Any hints on were to start? Thanks great video.
@n777rv
@n777rv 4 жыл бұрын
Go to Garmin's website and download the G3X installation manual. support.garmin.com/en-US/?partNumber=010-01057-00&tab=manuals Draw a diagram of your system and all components, then start figuring out which boxes need to talk to each other. From there you can start on a detailed schematic using the installation manual (IM) as your guide. The IM tells you what wire to use.
@KitfoxPilot
@KitfoxPilot 4 жыл бұрын
@@n777rv Thanks , I have been reading the downloaded manual for a while but having trouble finding my way around it. This is my first build so all is new to me. thanks I will get started on a diagram.
@n777rv
@n777rv 4 жыл бұрын
@@KitfoxPilot You should look into the EAA SportAir Electrical Workshop. eaa.org/Shop/SAW/Workshop_Details.aspx?workshop=electrical_systems_avionics
@johncarr123
@johncarr123 4 жыл бұрын
I found this on VANS website. www.vansaircraft.com/downloads/#ElectricalSystemDiagrams I wonder if they have diagrams like this for the other VANS model of aircraft.
@johncarr123
@johncarr123 4 жыл бұрын
Where did you purchase the manifold pressure switch block on your firewall?
@n777rv
@n777rv 4 жыл бұрын
Van's Aircraft #VA-168 $19.00. shop.vansaircraft.com/cgi-bin/shop.cgi?ident=1609459758-404-210&browse=ei&product=va168-va188
@sweetpickle57
@sweetpickle57 4 жыл бұрын
Spaghetti mess 😂
S-20 / S-21 Panel Fabrication, Avionics and Electrical Wiring
16:19
Sun Flight Aviation
Рет қаралды 9 М.
RV-10 Avionics - Magnetometer Harness Part 1 - Tools
15:08
BuildFlyGo
Рет қаралды 4,3 М.
“Don’t stop the chances.”
00:44
ISSEI / いっせい
Рет қаралды 62 МЛН
Мясо вегана? 🧐 @Whatthefshow
01:01
История одного вокалиста
Рет қаралды 7 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
RV-10 Avionics - G3X Wiring Overview & Planning
11:43
BuildFlyGo
Рет қаралды 2,9 М.
Harness and Connector Wiring - RV-7A | EP4.6
28:23
Ryan Flys
Рет қаралды 1,9 М.
Garmin G3X to GTN Crossfill
6:47
Midwest Panel Builders
Рет қаралды 18 М.
Shielded Wire Termination | ECUMaster USA
14:49
ECUMaster USA
Рет қаралды 19 М.
Shield drains for the Garmin G3X CanBus and RS233 lines
4:27
Aircraft Wire Testing
6:41
Paul DeWinter
Рет қаралды 8 М.
S14 (SR20DET) - Custom Wiring Harness Part 1 - How to Route the Engine Harness
17:27
Brain Power Motorsports
Рет қаралды 3,3 М.
RV10 Update Can Bus Daisy Chain
11:56
RVJimD
Рет қаралды 886
RV-10 Avionics - Interior routing & Device locations
19:18
BuildFlyGo
Рет қаралды 8 М.
Flying with a Garmin GI 275 MFD
6:27
Dennis Cheever
Рет қаралды 32 М.
“Don’t stop the chances.”
00:44
ISSEI / いっせい
Рет қаралды 62 МЛН