How To Golf mk4 Heated Seats Wiring Loom

Thanks for Watching! Please be sure to like and Subscribe! AND TAP THAT BELL!!
Follow Resto Designs : / resto.designs
NEW!
Resto Designs website : www.restodesig...
Welcome to a Golf mk4 heated seat 'How To keep your girlfriend happy' Video, In this video I'll show you what wires you'll need and were they need to go, great step by step video showing you start to finish.
Thanks for your supports guys!
Wiring Looms
partworks.de/e...

[@chrstphrr]

About the best video I've seen on the wiring part of the heated seat retrofit so far! Subscribed, of course once I started watching, since it details this retrofit better than any forum post or other video I've searched for. For those running the wires in: when I did my retrofit for power seats, which is similar: - find videos on disassembling the lower centre console (including the arm rest, the surrounding trim of the shifter, and the trim panel that is near the LHD accelerator pedal) - remove the front seats from the car (again, find a video, remember to have the battery disconnected or, have VCDS to clear airbag codes) - remove the lower A B, and C pillar trim, and around the door ways - remove the carpet... And, the trick that no one else seems to mention: make a single, cut on the carpet between the pair of dashboard support "legs" on the front tunnel, near the airbag module, toward the firewall, so you don't have to remove the entire dash to take the carpet out in one piece, unharmed. One little cut with a hooked carpet knife will let you remove the carpet in a spot that is simple not visible once all the trim is placed back on. Just be mindful to cut the carpet and not the wiring run in around there! Thank you for the video, this will be helpful for when I make a future retrofit to another mk4 car!

[@snowflake6916]

My girlfriend loves heated seats, so I guess she isn't the only one then lol 🤣 good to know.

[@RestoDesignsnando]

Yep trust me she isn't the only one mate, 🤣👊🏼

[@snowflake6916]

Lol ok so she's normal then 😂

[@RestoDesignsnando]

Seems like she could will be.

[@odilijussimonavicius3317]

I wired everything like in the video, however the passenger seat heats very slowly and driver seat doesn't heat at all. Any possible fix?

[@unknownaccount3111]

Could this job be done far quicker if I didn’t want the illumination for the lights is it the matter of plugging in the seats plugs and running the cable to the fuse box ?

[@TypeTalkspt]

Keep your girlfriend happy. Top! Nice content once again!

[@RestoDesignsnando]

Woman seem to love heated seats. 🤔

[@ah9869]

Hi, I have a mk4 golf comfortline. I'm currently upgrading the 2 front seats with orginal covers 1J0881405FNPDA. I see these come with heater elements attached. I can't get the back covers with heater elements. Will the loom that you brilliantly explained work with just the seat base covers or not. Or will there be too much current going to the seat elements without the back covers. Thank you

[@Gritchie.the.mk4]

Is there a video on how to actually get the wires/harness out of my donor car

[@archive.garage]

Thank you for your video and explaining the process

[@RestoDesignsnando]

Glad it was helpful!

[@ivann78]

Hi I've followed your vidéo using a kufatec loom, the red lights are coming on and i have 12v on the connector itself but nothing on the seat connector and don't know how to fix that

[@RestoDesignsnando]

ok no 12V on both seats?

[@ivann78]

@@RestoDesignsnando yes

[@ivann78]

@@RestoDesignsnando here are some measurements I've made: • left button pin 6 to 1 = 14v pin 6 to 2 = 14v pin 6 to 3 = 14v pin 6 to 4 = 14v pin 6 to 5 = 14v • right button: pin 6 to 3 = 14v pin 6 to 4 = 14v pin 6 to 5 = 14v

[@igniux]

very good video! You got a new subscriber :)

[@RestoDesignsnando]

Thanks friend 👍🏼

[@Jor02140]

Where should be connected the black/blue wire? You connect it to the obd, but i have a problem with that - when i switched the ignition on, the half fis says that i have 100km fuel, but the needle shows 1/2 fuel tank... Shouldn't it the black and blue wire goes to fuse 5?

[@raresra9614]

did you find the answer to this question?

[@robbievangeenenNL]

Great video! This will help a lot.

[@RestoDesignsnando]

Glad it was helpful mate. 👍🏼

[@babelonchabalala1690]

I've had my VW Mk4 1.9 Tdi for 3 years now .... Heated seats never worked.... Ive noticed the fuse slot is not wired so my guess is previous owner put a 1.6 petrol fuse box in it with heated seats not connected..... I will investigate further whether the 2 wires for the fuse might be hanging loose somewhere under the dash and then connect them and see what happens.... Thanks for the tip of how to access the fusebox from behind 👍

[@mrevoomk4]

Where is the main power source + , ? is that the 30 Red where the Red wire goes?, i wanted to connect my Voltmeter but i need an power source .

[@anthonykupchunos4282]

Great video 🎉

[@RestoDesignsnando]

Thanks

[@anthonykupchunos4282]

@@RestoDesignsnando is your mk4 content available? I tried looking for more. But nothing was categorized.

[@jacobhaddow9789]

How come you haven’t used relay 59 (the heated seats relay)?

[@RestoDesignsnando]

The mk4 doesn't have relay 59 like the mk3's, I think the relay/s are build into switches much like the hazard light switch which has the relay build into it.

[@jackcassidy6573]

Where did you buy the wires for the heated seats on your golf? I have the leather seats with the clip underneath the seat, but without the wiring into the fuse box Thanks for the video

[@alexandruvlas4549]

Try Kufatec. They also provide mounting instructions.

[@raresra9614]

I don't understand the role of the blue and black wire and where it should be connected more precisely. You say that it is the diagnosis wire, on other schemes on different forums it says that (it is connected to a 7.5A fuse and to 75 switched power which in turn I don't know what is it or where) I know it's been a while since you did the retrofit, but maybe you remember how it should be done more precisely, or if you had subsequent problems with your method. thank you

[@TIIRONC5H]

Pls wire lession For Acelerator pedal mk4 tdii alh i have Pedal cable and sensor idk how it called but i have no throtle body only injection pump

[@rotwiler12]

You said you would put a link in desc for Loom if not taken from donor car? Where is it

[@RestoDesignsnando]

OK OK chill out dude, 🤣 link is up. 👍🏼

[@rotwiler12]

@@RestoDesignsnando lol my bad didn’t mean to seem like I was upset

[@RestoDesignsnando]

@@rotwiler12 only pulling your leg mate, 👍🏼 My bad for forgetting not putting it up in the first place, thanks for pointing that out👊🏼

[@AndyNolan]

Shame it seems that company discontinued making looms for anything but Porsche. I'll have to do some research. I am really enjoying your channel, I would say I would have liked more footage of the actual "wrench work" sometimes, over a cut to finished job, even if it was sped up. On this one it's fantastic play by play, but cut on your suspension video. Im inputting purely as its would be cool to stick with you for knowledge rather than head elsewhere for that bit, because the content is superb, airbag was an example of a great cut away abc vid in a vid. The TT vs stock (non r32) mk4 comparison is the best out there even without a "how to" work through. Cheers fella, nice to have someone from home making great content, over the usa big personalities; something culturally direct about it, no fluff if you know what I mean.

[@RestoDesignsnando]

Thanks a lot, I really value your feedback 🙏🏼 you make valid points. I totally know what you mean, great thumbnail and title, great chat/storytelling, great editing skills, all to cover up no real info or meat in the sandwich. But that's a skill! and one I wish I had.

[@Editionone13]

👍😊

[@RestoDesignsnando]

Thanks friend 👍🏼