How To Ground A Car Amplifier 3 different ways

[@frotobaggins7169]

Nut serts are notorious for coming loose. Plus it holds the terminal up off the metal making the nut sert the only area of contact. I think the best connection would be a simple bolt with a nut on the back. You could always use some thread locker to keep it from coming loose or a lock washer. smear some grease on the bare metal to keep it from rusting.

[@user-cr4pz5yg7y]

Washer, lock washer, nut. Torque

[@luvdady]

If it's coming loose you're definitely not using it right.. That or your using temu garbage.

[@brookscalderone1511]

What size bolt works the best?

[@802Garage]

Excellent demo. Only point of contention for me is that if you have already cleaned down to bare metal I would not use the star washer. My understanding is that those are intended to cut through the paint to reach bare metal to create good contact for electrical connections. That's why they are used on factory ground points that go over paint. If you have already cleaned down to metal, I would just have the terminal pressed directly against it or add a flat washer underneath it if you need clearance for some reason. Drilling a hole and using a nut on the back is always my preferred method if a good factory captive or welded nut is not available. A nutsert should be a good option as well when done correctly, but definitely don't use them in areas exposed to the environment or where they will get wet because in my opinion it will invite too much corrosion.

[@IAM_HC]

I came here with plenty of knowledge on a good ground, but you just never know what you can learn and I still learned some valuable stuff. I’ve been using threaded inserts for years and love em. I’ll be combining that perfect circle wire brush with them going forward. I also didn’t realize those bolts paired with the lock washer and serrated nut were self tap. That’ll be added to the arsenal as well. Finding myself on this channel more and more

[@jptheinstallguy]

You can never stop learning and I try to gain knowledge so I can spread it. Tha ks for watching

[@Maxst33le]

Good spreading proper technique. Tbh I've had my sub and amp done by others twice and the grounds were always a little lazy, just drilled into the chassis one and done. I've since had to install the same setup 3 times and have done it way better without any effort. I sand down the surface with 60 grit to bare metal, use a big self tapper drilling it tight but not stripping the thread, can add a bit of loctite if worried about loosening but it's never happened to me. Top it off with clear coat over the finished grounding and once dried if you want to be a super pro, add peteolium jelly over the connection to completely lock it off from any outside elements

[@jptheinstallguy]

Sounds good my friend💪🏾💪🏾

[@Maxst33le]

Peteolium jelly trick is mainly to keep battery terminals corrosion and rust free by covering and keeping water out. Overkill for a ground if run in the interior but y not

[@thatmand4542]

@@Maxst33le That or some Di-Electric grease ! Its clear unlike the Petroleum jelly but either way it works great 😀

[@scottouimet2865]

I have that threated rivet tool. Man I hope it shows a good ground

[@DIYAudioGuy]

Pure fire! Great video.

[@jptheinstallguy]

Thanks brother 💪🏾💪🏾

[@darksu6947]

If your amp is grounded properly you won't have to worry about fire 😂

[@laptech3767]

The best answer is run your sub, and have a volt meter on the power input. If you have serious voltage drops it means bad ground, or bad positive side, or poor battery/ alternator. So you can pinpoint it with a volt meter easily. Troubleshooting one by one is best medicine to learning!

[@bubbawubba2307]

Looks like #4 has a lip on it . Does the connector make 100% contact with the metal or the threaded insert?

[@psycheeight082]

The thumbnail gave me PTSD.

[@JacobBitner]

Me too, in a way that I can't even describe. It almost pisses me off 😂

[@jptheinstallguy]

😂 doing the thumbnail made me cringe a little myself but it had to be done🤣

[@JonesingUSAF]

Why go the battery delete route instead of just adding the second battery for the system? Genuinely curious.

[@jptheinstallguy]

I didn't want to use a battery isolator and this lithium battery can run the whole car and the audio system. I guess it should be a battery relocate because it's in the back and not the front.

[@brandonfoss9445]

With the nutsert, I don’t think you need to grind the paint off the surface of the vehicle because the nutsert is making contact with bare metal inside the hole that was drilled for it, and it protrudes slightly, keeping the end of the wire out of contact with the vehicle. The only electrical connection is through the nutsert itself, so grinding doesn’t do much if anything.

[@MrAndresm900]

Thanks for all the help you upload

[@jptheinstallguy]

Anytime💪🏾

[@bigernmccracken712]

You share some quality info JP, thanks!

[@jptheinstallguy]

I appreciate that!💪🏾💪🏾

[@tranquillitymedia]

Anyone know where I can get the drill bit

[@deedolan399]

Very detailed. Great video

[@jptheinstallguy]

Glad you liked it

[@Insight2.0l]

The star washer (not lock washer) should go between the lug and the metal. Also if you want it to not rust use weld through primer. It is conductive primer.

[@JonesingUSAF]

Steel-It is the shit! Conductive, protective, and even weldable!

[@Insight2.0l]

@ Learn something new everyday

[@mr.89irocz]

Is one ground from the battery to chassis all you need or depending on how much power you have? Also can you just wire the amp ground to the battery then battery to chassis or amp ground to chassis and battery to chassis? I’m new to car audio and I want to learn.

[@ssjdavid]

The battery is always the best ground or straight off the alt

[@BobBasshead]

You made some good points with your question. 👍

[@thatguykai479]

Thoughts on alternator bracket back to ground location / frame in car ? Heard this was one of the best grounds also if you could link that tool used on the 3rd bolt with the wire brush and drill in the middle can’t find it

[@Emotionalrealms]

Not question is is that I have a 5 channel amp. Do I need an RCA for each speaker I guess that's where I'm confused or do I just wire all 4 speakers to the sub.

[@Skipzz97]

Hey jp quick question video where you show how to find max from headunit with smd dd1 you mention to put subwoofer all way up befor tuning my head unit had eq setting & audio controll settings they both have subwoofer levels do they both need to be turnt up to max or just one?

[@904lava]

Can i just use an existing ground

[@flsabvb7578]

What is bit called that has the short bit that cleans the surface called. Thank you

[@michaelmincey2622]

What do you think about using the seat belt bolts in the car?

[@jptheinstallguy]

I dont use them but if you can check resistance on the point and if it's close to 0 should be ok

[@AlexanderStein-db3ro]

Where did u get the tool that makes the perfect circle for the paint removal and what is it called? Do u have a Link ?

[@jptheinstallguy]

I'm still trying to find where I got that from when I find it I'll link it with the other products in my description

[@PCheriyan007]

@@jptheinstallguy it's called a "pilot bonding brush"

[@bobbybyrkett7751]

Great video 👍

[@jptheinstallguy]

Thank you💪🏾

[@drake8805]

Drill hole, scuff both sides of frame, use bolt and locknut = more contact area and lower resistance compared to other options.

[@dhg1839]

i might be wrong but i always put the lock washer under the wire not between it and the screw, my thought is that the star washer digs into the flat metal grounding surface. please advise

[@Carlossteezyblunts]

I want to run a ground to my frame but I don’t have access to back of the frame to add a nut. I don’t think I can fit a rivet tool down there under either. Are there any tricks to get a nut and bolt on a frame when you don’t have access to the back side of the frame?

[@jptheinstallguy]

Well the good thing about those bolts in this video is that they are self threading bolts as long as the metal is thick enough the bolt will cut threads into the metal and you won't need the nut cause it will be super tight, the lock washer helps with that as well

[@Carlossteezyblunts]

@@jptheinstallguy okay great because I was really hoping if I tried using the bolt in the video I wouldn't need the nut but wasn't sure. My frame is pretty thick so it should work just fine. I'm going to order some power wire over the weekend so i can redo some of my runs, I will get the bolts then to. Thanks !

[@themeez1000]

I just want to know what that bit is called that removes the perfect circle of paint

[@chuch93]

Pilot bonding brush

[@themeez1000]

@@chuch93 Apprentice it!

[@wilsq30]

Who the eff puts three screws in 😂

[@noahbergeaux9709]

People who have had to track a bad ground 😭😭

[@rickross368]

Car audio shops put 3 screws in ground terminal, had a car audio shop do that to me once. Had to redo it cause didn't like how it looked😅

[@1VIPWRX]

Great video

[@jptheinstallguy]

Thank you

[@terrancemjr]

I have the 3 screws but doesn’t look neat to me. I’m gonna change to the next option

[@alexdantzler8236]

Awesomeness³

[@nyny201994]

Where are you located?

[@Packersnbassforlife]

Nice video

[@jptheinstallguy]

Thank you

[@Packersnbassforlife]

@jptheinstallguy still waiting on the grand marquis video. For running 1/ 0 gauge amp wire to back or 2 1/0gauge wires. Ha ik it's some kind of snakes thing people use

[@Packersnbassforlife]

@jptheinstallguy ha I got. A guy use a coat hanger n attach the wire to eat with tape but if u do a video tagged me in it

[@omarherrera8361]

What is the drill attachment for the 3rd option called?

[@jptheinstallguy]

That's just a 1/4 inch extension and a 13mm socket

[@omarherrera8361]

@@jptheinstallguy I meant the round sander thing for scrapping the paint

[@ICP1SBJ]

pilot bonding brush

[@omarherrera8361]

Thank you sir

[@knock904]

bro if i become a patron // will u help me //i bless u

[@cristovalmontoya5222]

Just use a pre drill than a tap threader set and the right size bokt if you metal is thick enough and you don’t need a nut cause it makes its own threads I’d still use a star lock washer or bolt that has a locking head. ? Bi like that wire sander with the point that sweet.

[@dresanti5274]

💪🏿

[@ssjdavid]

Straight off the battery always worked best for me

[@DemonOfFury]

Nut and bolt are the only option

[@jptheinstallguy]

Agreed 👍🏾

[@ZeeDuckMan]

I don't even use screws in the first place.

[@jptheinstallguy]

That's awesome

[@kitcat2559]

The best way to ground is a minimum of 1 box of screws per CM of course 0.0

[@MoToArchY]

I just posted a video about running lithium under the hood! So I wouldn’t have to go with a battery in the back

[@jptheinstallguy]

There are lithium batteries that can be mounted under the hood but this one was not one of them 😂🤣

[@melissathompson7229]

Pozitivground kit. The only way to go. If your shop owner is too cheap to buy the kit, find a new place to work

[@jptheinstallguy]

Yes i love that kit

[@chrisking-jp5kj]

No sound???

[@southern_merican]

2:00 I understand you're trying to make a point but that wasn't even tight!

[@k1ngzflayze832]

He’s saying it’s not a good ground

[@3zRattl3s]

my amp is always going into protect mode i have a fosgate p3sd2-10 2 ohm wired to a fosgate 300w amp do i just need a bigger amp?

[@takohma1056]

Nutserts are cool until they spin around 😂

[@cagentry93]

Just use the tool to re tighten. It’s good as new

[@RobbertW2]

Great instructions, but i dont think we need to let people get away with the second method anymore. It still leaves a lot of room for error, making it just slightly better then the first method. Wiggle the cable around a couple of times with the second method and it bet its able to rotate.

[@jptheinstallguy]

Yea im not exactly encouraging anyone do options 1 or 2 but we also have to be realistic that some people aren't going to invest in the tools and products to complete options 3 and 4. So if someone is going to use self tappers I rather you not do option 1 at all

[@reecebower9934]

If you need a tutorial on how to ground something you should not be working on electronics lmao

[@keepitthoro6768]

Battery delete is stupid,dont do it! It can be done with out a "delete "

[@jptheinstallguy]

I said delet but I meant relocate it's installed in the rear instead of under the hood

[@roynorw]

Beginner Intermediate Pro and you doing too much😂

[@elviscaragea4433]

no ohms testing, disappointment

[@jptheinstallguy]

You must not have watched the whole video

[@elviscaragea4433]

@@jptheinstallguyyou didn t test them separately with a multimeter

[@rickytate9515]

What size is that nutsert