How to Hardwire Install your EV Charger

In this video, I demonstrate how I DIY hardwired my EV Charger (Electric Vehicle Supply Equipment or EVSE). There is a lot of information in this video, more than just the charger installation steps. I show you my tips and tricks throughout the project, how to get through challenges when things don’t go as planned, and how to build a PVC board box to protect the charging cord if you are mounting your charger between two garage doors. I also talk about what my preferred amperage to charge at is, so make sure you catch that at the end of this video. Please read the ***electrical disclaimer below, and understand it’s very dangerous working in your attic. One wrong step, and you will fall through your ceiling.
Please LIKE and SUBSCRIBE if you enjoyed this video to help my channel grow.
CHECK OUT my “EV Charging Cord Protector for Under Garage Door Charging” video here: • How To Run Your EV Cha...
For any questions email me at: [e-mail]
***Electrical disclaimer:
It is important to note that any electrical work should be performed by a licensed professional. The information provided in this Home DIY channel is for educational purposes only, and is not intended to replace professional advice. The channel owners and contributors cannot be held responsible for any damages, injuries, or losses that may result from use or misuse of the information provided. Viewers should always use their own discretion and consult with a licensed electrician before attempting any electrical work. Also, in most cases, you will need to pull an electrical permit to install a new EV charging circuit. Rules can differ from one city or municipality to another.

[@HomeDIYwithMartin]

CHECK OUT my “EV Charging Cord Protector for Under Garage Door Charging” video here: kzbin.info/www/bejne/gpzHi2eQetCApposi=vGfFIsh5Zwv92yJ0 In this video, I demonstrate how I DIY hardwired my EV Charger (Electric Vehicle Supply Equipment or EVSE). There is a lot of information in this video, more than just the charger installation steps. I show you my tips and tricks throughout the project, how to get through challenges when things don’t go as planned, and how to build a PVC board box to protect the charging cord if you are mounting your charger between two garage doors. I also talk about what my preferred amperage to charge at is, so make sure you catch that at the end of this video.

[@loucinci3922]

I like your thinking about wire size - it’s better to have it and not need it than to need it and not have it

[@HomeDIYwithMartin]

Exactly! Just incase someone behind me changes the settings, uses it, it is ready for its max capacity. Plus, I do use it at 48amps when I need it, been a year, 2 EVs use it everyday, works perfectly.

[@loucinci3922]

Enjoyed the video. Thanks for sharing

[@HomeDIYwithMartin]

Thanks for watching and commenting! I appreciated that!

[@santoshbansode697]

Thanks for everything ❤❤❤❤❤❤❤❤

[@HomeDIYwithMartin]

Thanks for watching!!

[@williamgrissom9022]

Individual stranded THHN 6 awg wires might have been better than the 6-2 NM (Romex) cable you used. Probably less expensive. It has a higher temperature rating (90 C) and thus a higher current rating (recall 55 A in conduit, for 2 cond max). Much easier to pull thru conduit. I bought it by the foot recently at Lowes for another project (now planning for an EV charger). They had red, blk, wht, and grn stranded. Home Depot had only 2 colors by the foot in 6 awg, at higher price.

[@HomeDIYwithMartin]

That will work great for you, enjoy your install. Thanks for watching!

[@dannelson6980]

I hate to break it to you, this does not meet code for a 48 amp continuous load. From Southwire - "Southwire® Romex® Brand SIMpull® NM-B (nonmetallic-sheathed) cable may be used for both exposed and concealed work in normally dry locations at temperatures not to exceed 90°C (with ampacity limited to that for 60°C conductors) as specified in the National Electrical Code." So you should only charge at 40 amps. NM-B cable tightly bundles the conductors together and traps the heats in the cable assembly, which why you have to use 60C rating for ampacity. If it was 75C or higher copper THHN in conduit there is more space for the heat to dissipate and would meet code. All the EVSE manufacturers need to be more clear in the instructions and not depending people's (including residential electricians) knowing this often overlooked part of the NEC.

[@HomeDIYwithMartin]

On every KZbin EV Charger install video there is a comment exactly like yours. And you are right, all the EVSE manufacturers need to be more clear with their instructions. I also think the wire manufacturers should actually sell wire rated, and then branded/packaged for EV charging. Not just for DIYers, but for electricians too. Hopefully you watched the whole video through but I do recommend charging at only 40amps. Although the 1% time I do not and everyone else that uses similar rated wire…just hasn’t experienced an issue. But I would just continue recommending charging at 40amps because it simply not necessarily with home charging to charge at your EVSE max output. The time savings in the middle of the night is minimal. My EV charges nightly on average for 2hrs or less with my daily driving at 40amps. So that’s what I leave it at and because of what you explained. But thank you for sharing your info and I would also recommend for everyone to consult with their electrician for their use case before installing a home EVSE/Charger.

[@PeaceChanel]

Thank You for All that you are doing for our Planet Earth.... Peace.. Shalom.. Salam.. Namaste 🙏🏻 😊 🌈 ✌ ☮ ❤

[@HomeDIYwithMartin]

Thank you for watching!!

[@TexDeafy]

Wife: Where is my lipstick with black cap on it? He: Uh, I use it for DIY projects. Why? Wife: I need it for dinner and I've changed my mind to donate it to you for your Do It Yourself something like that. I need to use it for special occasions. He: Well honey, I'm sorry but I had to throw it away because I've use it all for several of my projects. Wife: KABOOM! (Slap in his face so hard) He: Whoa! My cheek feel stingy from your powerful hand! Why you do that to me?! Wife: I forgot how expensive this lipstick was and honestly it's no longer exist, I really need it for that special occasion... I love that color! He: Honey, I'm sorry but I thought you no longer need it and donated it to me for my project! I'm just joking around, buddy LOL

[@TexDeafy]

By the way, you did nice job on this EV charger! :)

[@HomeDIYwithMartin]

LOL :) Thanks for watching!

[@nelnotheamoeba9221]

After watching a dozen or so of these types of videos, each of which has one or more comments about the wire gauge being incorrect, as well as comments from people whose electricians did it wrong, or even comments from supposed electricians getting it wrong, I am seriously wondering if there is a high likelihood that I would get a incorrect install from an electrician at this point.

[@HomeDIYwithMartin]

Go with Qmerit. They specialize in EV Charging installs. If you watch the part of my video after the app setup, I do talk about what I chose, and why. I put that part in there knowing I was going to get comments about my install :). Just about every single EVSE install video has similar comments. They just copy and paste.

[@i6s1]

You shouldn't use the 48 amp setting. You've got Romex wire, you have to use the 60c rating, so that's 55 amps. Max continuous would be 44 amps. You should have finished the attic run and used THHN wire, then you could have used the 75c rating of 65amps. You would have been able to charge at 48 amps then.

[@HomeDIYwithMartin]

I address this in the video (if you watch the whole thing) and on previous similar comments. Works great, 2 EVs charge daily. Thanks for watching!

[@4x2-ev]

As previously mentioned, this will not pass inspection. First, you should always get a permit and inspection. Our utility offers installation cost rebate and requires a passed inspection (aside from just keeping people safe.) It is not just setting the charger to a max of 50 amps output but the 60amp breaker is too big for the wire type and needs to drop to 50. If I install an EVSE with a 60amp breaker to achieve 48 amps on the charger, I need to use either #4 romex or #6 thhn in conduit.

[@HomeDIYwithMartin]

Read my previous reply to very similar comment. Thanks for watching!

[@jasnapon]

Gas forever🤣

[@HomeDIYwithMartin]

Depending on your age, you might be able to 😉