Car Failed smog do to purge valve/flow engine code P0441. Diagnose and replace purge valve.
Пікірлер: 78
@joehyundaitech79615 жыл бұрын
hi Larry im a hyundai tech they have a lot of issues in general there all junk the most recalls of any car on the road today
@Found46554 жыл бұрын
I have a 2008 Hyundai Santa Fe. Purchased it 4 months ago with approximately 127k miles. Had same code P0441. Replaced it 2 1/2 months ago. Used a part from Autozone Now the code is back. .. should I have used only a dealer part? Any advice would help.
@-CCdude6 жыл бұрын
dude it would have been nice to see what tools you needed to remove it instead of fast motion video
@robbbarnett49786 ай бұрын
Have 2014 hyundai accent that had same issue and replaced as soon as i bought it and fixed, but had to replace it the other week after only year and a half?? It worked again, but after market one didnt last long and replaced with another after market one so we will see how long it lasts this time. Still got 40 plus mpg with issue so it doesnt effect mileage.
@loaked30002 жыл бұрын
Thank you!!! This was my exact issue, you saved me $$ MUCH appreciated!
@JayCeeMax4 жыл бұрын
I just replaced the Purge Valve for a 2010 Elantra. The location of components are a tad bit different. I vlogged about the simplicity of the removal and installation as well. It was difficult to start the car after filling the tank. Replacing the purge valve fixed it. Thanks Man Meets Garage!
@dt528bmw3 жыл бұрын
My Santa Fe had the same problem. The new valve fixed the problem and the check engine light also went off. (disconnect the battery and reconnect to reset the the check light.)
@JayCeeMax3 жыл бұрын
@@dt528bmw I'm happy you were able to fix it.
@jacarts27934 жыл бұрын
FYI, on my 2008 Hyundai Santa Fe, the purge valve is mounted on the passenger side of the intake manifold, easy to reach. Square unit with both vacuum tubes on top. Doesn't seem to be an after market replacement though.
@Mrimpact20114 жыл бұрын
I just replaced the same Purge Valve for 2008 Hyundai Santa FE: Additional tips: Pinch with your thumb the electric connector to remove Purge Valve. Use long nose plier to pinch clamps and slide to right. Slide old Purge Valve to left from metal bracket. The left tubing is difficult to remove. I had to cut. Buy new Purge Valve with left rubber attached outlet. Use proper light. Installing is the easy part. Total Time: 1 hour . DIY saves you $100-200 from mechanic. $9-15 Part on Ebay. Tools used: 10mm socket, Phillips screwdriver, Long nose plier (small).
@dt528bmw3 жыл бұрын
You were not kidding when you said it an an absolute pain in the butt to replace. Also, I ordered a replacement online and it was the wrong one...the contact pins did not match. I went to AutoZone and found the exact match. $58 vs. $18 for the eBay part. Hyundai parts dept. wants $180 for the same part. Car dealer parts are such a rip-off. Thanks for the post.
@berzerker11007 жыл бұрын
awesome vid. great Thanks for posting !
@ManMeetsGarage7 жыл бұрын
Thank you
@PartySearch2475 жыл бұрын
I have a 2007 Santa fe that makes a clicking noise (but not all the time, on and off) from the same area of the engine. Could that value be the click maker?
@coinrush49843 жыл бұрын
#bitcoin #crypto #DIY what engine is this 1.6 , 2.0 ?
@Them35310 ай бұрын
Would these instructions work for a 2008 Accent?
@johnnyz12 жыл бұрын
replaced purge valve didnt solve problem.mind turn out to be a vacum leak from the brake booster hose,
@eloymartiz83495 жыл бұрын
PLEASE MAKE A VIDEO HOW TO POGRAM A REMOT KEY ON A 2006 HYUNDAI STA FE2.7L SPECIALLY? THANK YOU.!!
@johng.49595 жыл бұрын
Great video!. Thanks for explaining it the way you did and showing us the location!
@MrPeterHaller2 жыл бұрын
How do you determine if the canister purge valve, or the valve in y engine is bad?
@pattencycling Жыл бұрын
Nice video bro
@stephentrujillo75552 жыл бұрын
@man meets garage. I've a 2007 Hyundai entourage and it will not fill up gas properly. It only fills little bit at a time. Like the vent valve is blocked. Could this be the issue? What you showed in the video i mean.
@ulisessantoyo2437 жыл бұрын
hey so i replaced my purge valve as well on my veloster and erased the code after that as well. but my tester reads the po441 in permanent codes. is it normal ?, no engine light tho
@ManMeetsGarage7 жыл бұрын
Drive the car about 30+ miles with starting and turning off, Sometimes it needs a reset.
@gavin91746 жыл бұрын
where is the purge valve on the veloster... i cant find it haha
@buzoff46425 жыл бұрын
So why are mechanics saying P0441 could be [list]? Is that because they don't really have an accurate ODB reader?
@leftylou60702 жыл бұрын
Maybe check for a faulty gas cap, and electrical connections first and it could save you $70 possibly. Thanks for the informative Vid!
@marccohen13353 жыл бұрын
Very good. Thanks.
@TheMyisa5 ай бұрын
What year vehicle is this?
@eloymartiz83494 жыл бұрын
CAN YOU PLEASE TELL ME WHERE IS THE LOCATION OF (THE ON AND OFF DEVICE) TO PROGRAM MY REMOTE CONTROL ON MY 2006 HYUNDAI STA FE?..ONLY THIS YEAR!! THANK YOU.!!
@rowaidd43554 жыл бұрын
I have Hyundai Sonata 2011 it has small lack in the evap em . So what’s the problem that is causing that . Plz help
@beatlesnmore3 жыл бұрын
due to, not do to
@arashebadtabrizi13013 жыл бұрын
Does this problem make your gas go out faster ?
@hugolob981111 ай бұрын
Thanks for the video I changed my 15 min save money
@link5606332 жыл бұрын
Does this purge value also cause the car to have trouble turning on after I pump gas?
@supernatural53546 жыл бұрын
Just replaced my Purge Valve but check engine light is still on and the code P2189 pops up, along with p0441, p2187, p0456. What should I do?
@yamin.chhipa2 жыл бұрын
You're the perfect representation of how everyone of us has a role on this earth, thanks a ton
@rodrigovavalis97083 жыл бұрын
Man , can the purge valve cause any intermitent noise like a knocking or tiking valve or something?
@eduardchavez5 жыл бұрын
Excellent video, I have a question... does that valve helps (Break Power Booster) in hyundai santa fe? I have change the master cylinder and the power booster. When I press pedal very hard, that gets discharged.
@whistlesullivan4927 жыл бұрын
great vid I have the same code but it does not say valve it says large evap leak what can it be the gas cap is new from hyundai my car is a 04 santa fe 2.7
@ManMeetsGarage7 жыл бұрын
Start your engine and open your hood. Look and listen for a steady hissing sound. Let me know if you hear anything.
@leedress21876 жыл бұрын
what was the part number? I can't find that exact item when i look for the purge valve on Hyundai parts sites.
@ManMeetsGarage6 жыл бұрын
Sorry don't remember. Give them your make model year and they should find it.
@leedress21876 жыл бұрын
I found it. thanks.
@tersawhite90786 жыл бұрын
2006hyundi elantra auto zone say O2senor it runs good then start it wants to lose power mash gas it go but when I'm at a relight it barely go then it pick up it start to sputter like it can't get any gas
@charlesanderson61154 жыл бұрын
What is the name of the hand tool used in this video to test vacuumat about 6min?
@Mr71chevyvan3 жыл бұрын
your excellent video was a "what to do" w/o a clear "how to do"
@IshMotorparts5 жыл бұрын
Good job pro
@inmyopinion6516 жыл бұрын
Have same problem with wifes Santa Fe.. everytime put fuel in car you have to sit and wait for it to start. Thanks for this awesome vid.
@marknir5 жыл бұрын
Did you get it fixed?
@jaymcdonald97657 жыл бұрын
Thank you for posting this video. you saved me so much trouble
@mikerobi61007 жыл бұрын
nice helpful
@aggiemusic20156 жыл бұрын
Great video and Merry Christmas. Very easy to follow.
@g.m.c.r.w48886 жыл бұрын
plz make a video for cam shaft senser checking
@clobbersnoggin6236 жыл бұрын
How the hell do I get the electrical connector loose? Can’t figure it out about to break it. I know it’s got to be easy but I don’t know how
@Them35310 ай бұрын
Its very hard. We broke the rubber.
@Texasdope115 жыл бұрын
Do you know the location vapor vent valve on a 2002 Hyundai Santa fe?
@munazzas82835 жыл бұрын
Hello, I found a video where some was looking for purge valve. kzbin.info/www/bejne/sJ-cfGWYar-sa6c I hope this help best of luck
@Kodo9mm5 жыл бұрын
How did you take it off that bracket man? I’m having a lot of trouble
@fatalityxd865 жыл бұрын
If you kind of peel it apart, the rubber bracket will stretch and come off.
@alyssashao7 жыл бұрын
Very clear, thanks a lot.
@ManMeetsGarage7 жыл бұрын
Thank you
@alexandertarnai53896 жыл бұрын
Help! How do you get the hose from valve to intake manifold off. Neither side of it will move at all
@dt528bmw3 жыл бұрын
They dry out and get hard as a rock. I cut mine off and replaced the hose with a new one.
@roysanchez83845 жыл бұрын
Can you get a miss fire for not replacing it soon?
@munazzas82835 жыл бұрын
No if you get a misfire it has do with something else. ICauses include worn, fouled or damaged spark plugs, bad plug wires or even a cracked distributor cap. A weak coil or excessive rotor gas inside a distributor would affect all cylinders, not just a single cylinder. ... If two adjacent cylinders are misfiring, it's likely the head gasket between them has failed. You get different engine light code Diagnose and investigate: Ignition Choose your plan of attack - cheap to expensive, easy to difficult - and stick to it. It’s cheap and easy to start with ignition items, so we went to the spark plugs. Because the P0304 had repeated, the #4 plug came out first. It read lean (a gray-brown, not bad but trending hot and fuel-starved), predictive of a fuel problem rather than a spark problem. The repair and replacement (R and R) of fuel injectors is a bigger project than the plugs, so we stuck to the plan and stored the knowledge in case ignition repairs failed to fix things. The other plugs had been replaced about 20,000 miles earlier and looked almost ideal. Every one was in good shape, short of the lean read on #4. We cleaned them up and swapped the plug on Hole #4 with #2. If the problem were the spark plug, the misfire would move to #2. It didn’t. P0304 came back.
@dennismadigan20236 жыл бұрын
Thanks. Great video it helped loads.
@malignantflesh5 жыл бұрын
Thanks for the video.
@evelkenevel79485 жыл бұрын
Do you have to reset the check engine light? or will it go off on its own?
@ManMeetsGarage5 жыл бұрын
Mine went off after about 30 miles of driving
@jaydegroot28325 жыл бұрын
Well your suppose to unhook the battery while doing this and that alone will take care of the code. This is q bad example I'm only here cause I had to fix my mom's and she asked why I didn't do certain steps he did well its because this is a easy fix maybe because I do this for my job but hey he got it done so
@KevinAshcraft6 жыл бұрын
Thanks for the help!
@Kairi0915 жыл бұрын
This is a solid vid but I can't find the damn purge valve in my engine!!!
@angelmagichands21716 жыл бұрын
THANKS for info!!😉 But you talk to much in the beginning!!😵
@petar4437 жыл бұрын
Why don't you do a Corvette project?
@ajseuol18645 жыл бұрын
Dude you're giving Miss information to the world. 10 psi? That is a vacuum pump it reads in inches not pounds per square inch. Common Mistake by a rookie. If vehicles were easy to work on anybody could do it.