Me with 20yrs + experience,2 broken fingers and 5 new swear words later mad cause you made it look sooooo easy… and I’m off to the auto parts store smh. Thanks bro
@Everything-hilarious4 жыл бұрын
When working on injectors and fuel rails pull the fuel pump fuse or re route feed back line and let run until it stalls and will relieve all pressure in the system before disconnecting. Great work tho 👍🏻
@davidblake21012 жыл бұрын
Thank you very much! I had a bad injector and replacing it was easy thanks to this video!
@SchClean2 жыл бұрын
Doing these now. We just did the plugs and coil packs. Thank you brother
@jonathandelarosa75682 жыл бұрын
Why don't yall ever show the whole driver side take apart
@NanoDiaz7772 ай бұрын
Hello, excellent video !! congratulations. Only a doubt that did you put the oring of the injectors to lubricate them before installing them?
@theswinecrew2 жыл бұрын
I am getting ready to swap out my spark plugs and coil packs, my fuel injectors, and the leak detection pump. I've personally put on 92,500 miles on my 16 Ram 1500 so, I want to give it an overhaul rather than picking away at each item. I noticed my fuel economy took a serious dive so, I am hoping my fuel system will start performing a lot better than it has been. I've been burning close to 6 Gallons of gas every 30 miles on a 24 Gal tank. I watched your videos on everything I've mentioned and have been researching coil packs, even sought out the socket you were using with a swivel. Would ENA be considered a good way to go. The money I am spending is starting to add up, but the fuel loss far out weighs this set up on money spent. I just don't want to get into the $30 coil packs O'Really wants to sell. ENA Set of 8 Heavy Duty Ignition Coil Pack and Set of 16 Spark Plug Compatible with Ram Chrysler 1500 2500 3500 5.7L 300 5.7L Replacement For UF504 $227.99 GEARWRENCH 3/8" Drive 6 Pt. 5/8" x 6" Magnetic Swivel Spark Plug Socket - 80546 $13.98 AUTOKAY Fuel Injectors 05037479AA Fit for 11-17 RAM 1500 2500 3500/06-17 Dodge 5.7L V8 (Pack of 8) $127.89
@rickclark55473 ай бұрын
Good video thanks for the help
@nancyvilla71353 жыл бұрын
Grasias por tomarte el tiempo de mostrar este vídeo tan importante y tan claro de entenderlo Grasias dios lo bendiga
@detectivethomas840610 ай бұрын
Thanks for sharing!
@venomhemi39143 жыл бұрын
clean video, thank you!
@jlstrad193 жыл бұрын
whole ass Viper just lurking in the background lol
@BoostedMotorsports3 жыл бұрын
Haha check our new exhaust video we just posted up 💪
@jew59132 жыл бұрын
Very well down. I haven't any work since 20 yrs ago but you video and only yours was well done. However, i wish you might shown a little more on the driver side it is a little more cworded. but i am sure i will get it done. There was one that happened with me maybe not everyone but all of my clips were sprung getting off but a little squeeze with the pliers put them back in shape.
@jasonslabaugh57836 жыл бұрын
My Lord why are you not driving that Viper around? Lol I'd be lucky to just sit in one! Good luck to you in your boosting endeavors! Anxious in your build :)
@BoostedMotorsports6 жыл бұрын
I definitely drive it! I made a ton of videos on that build on this channel you can check out but everyone enjoys the RAM content more!
@loganmartin26674 жыл бұрын
hey man hope you see this I’m having a trouble with the harness to the injectors, i got the red clip up but I can’t unclip them
@loganmartin26674 жыл бұрын
actually i figured those out but now the red connector that’s on the fuel rail?
@GloryOfSatan3 жыл бұрын
whats that manual youre using?? i need one like that haha
@benw.25535 жыл бұрын
Nice ive got a d1sc ready to go in once I buy new injectors. procharger only comes with 39.5lbs injectors. My 400 ci needs 65 lbs injectors so I just ordered the tuner kit. diablo sport tuning here no HP.
@whitrob4 жыл бұрын
Whats that book your using for reference? and where can i get one?
@GloryOfSatan3 жыл бұрын
this i need to know!!!!
@boosttapperformance86735 жыл бұрын
What's the flow rate on the stock injectors you have any idea?
@cory76234 жыл бұрын
Having nothing but issues on my 13. Keeps showing a misfire on cylinder 6. Did the plugs and put a new coil pack, worked for a tank of gas with some injector cleaner in it. Now it's doing it again. Gonna try an injector next, just praying its not a stuck lifter
@joshgsxr10004 жыл бұрын
I'm in the same boat you are, please let me know what you find out.
@cory76234 жыл бұрын
@@joshgsxr1000 it ended up being the MDS system. I bought a tuner and turned off the MDS and havent had a single issue since
@tuckerlovett27162 жыл бұрын
What kind of symptoms where you having outside of the check engine light?
@guil_juliao Жыл бұрын
@@cory7623 Hi Cory, I know this is an old thread but wanted to ask which tuner you got? I have an 11' Ram 1500 with the same issues. Thanks!
@inktheghost3 жыл бұрын
I’m sure I know answer to this. If I am doing a 5.7 swap to 6.4 manifold I should do the fuel pressure release also when I start the swap? I’m about to do one on my 2021 1500 Rebel and am just getting the last bit of info I need to do the work myself. Thanks man. Again you have help me a lot on past with your videos
@johnscars825 жыл бұрын
just curious: is it recommended to replace the sensors with a tuneup? I am due for new plugs, etcetera and overdue for injector cleaning, but I replaced the MAP, EGR, PCV valves less than 50K miles ago.
@aaronfogatu3 жыл бұрын
I'm having problems where some of my injector harness don't have the red clip but when trying to put the harness on the new injectors it doesn't clip in when pushing it together it just continues to pop back up a little .
@nickduran21895 жыл бұрын
One of my cylinders keeps misfiring, I already changed out the coil, spark plugs and fuel injector.Is there anything more I can do before I take it to a repair shop?
@JamesTaylor-du3oo5 жыл бұрын
Having the same issue. No luck for me yet, just a bunch of forums that end up getting waaaaaaay off topic, an no solution
@vanessalong75525 жыл бұрын
Just found a broken ground under my 2013 2500, we have a misfire aswell, injector is the only thing I haven't tried, but maybe check the grounds
@kevinsingh19874 жыл бұрын
Sounds like you may have the dreaded failed lifter which eats the cam lobe... Causing a misfire. One way to check is pull the valve cover and crank the engine. You should see the suspected bad valve spring moving less than the others. This issue is well documented by others and the only fix is to replace the cam and lifters.
@wadetaylor31954 жыл бұрын
It’s been a year, what did you find out?
@bigdaddysshop81802 жыл бұрын
Get ready to change the cam and lifters.. cams In those are soft..
@MrCARDENAS14 жыл бұрын
I had a question in the video at approximately 8 minutes and 45 seconds the O-ring comes out from the top of the fuel injector and the rail but you put it in the bottom of the fuel injector is that correct does it belong on the top where it came out from or on the bottom of the fuel injector
@BoostedMotorsports4 жыл бұрын
There are o rings on the top and bottom of the fuel injector to seal on both sides so you have to make sure you have them both on so you don’t get a leak from either side
@drnutell3 жыл бұрын
Why don't you tell us where to get the manual?
@BoostedRam4 жыл бұрын
Why do you have to remove the fuel pump fuse, what happens if you leave it on?
@skipwilliam56393 жыл бұрын
when the fuse is removed the pump wont work so when you start the truck It will burn the fuel in the line thats still under pressure and no more fuel will come out of the tank so there isnt anymore pressure in the line after it runs for 2 seconds.
@tonymadden22195 жыл бұрын
Love these videos man, I have a 2015 sport crewcab. Was also curious if you could tell me what manual is that you are using, because the one I have sucks.
@BoostedMotorsports5 жыл бұрын
Thanks Tony! I honestly don't use a manual and just try to come up with practical methods for getting the job done. Only time I really use the manual is for tq specs 👍
@galindoyovani11 ай бұрын
what kind of manual is that where can i get one?@@BoostedMotorsports
@danielperetto97226 жыл бұрын
Any word on the transmission tune I am looking to get a tuner and don’t want any problems because my ram is my daily driver I have only had it maybe three months and it has 11000 miles
@BoostedMotorsports6 жыл бұрын
Still dealing with it but I'll update everyone in tonight's vid 👍
@milesdomagalski64813 жыл бұрын
Minnesota?
@pasqualesibilio70044 жыл бұрын
Hello my 2011 Ram 5.7 Hemi have misfire on cylinder 2 but injector inspectioned with apposite machinery result ok and is well also spark plugs. Engine turn on 7 cylinders, there is not metallic noise for think at lifter and cam. Where is the problem? May be the ECU ?
@bigdaddysshop81802 жыл бұрын
Cam lobe is starting to wear off..
@jeffreyperry97736 жыл бұрын
Why did you reinstall your factory intake?
@BoostedMotorsports6 жыл бұрын
I sold my K&N since I knew I wouldn't need it with the procharger and could use the funds elsewhere. I did like the K&N intake while I had it though. Sounded awesome! 😎
@loudastous11593 жыл бұрын
Pulled into a place the other night and my Ram just died,tried cranking it, it slow cranked but wouldn't fire,waited about 30 minutes,it fired up and the lifters were clattering,drove it down the street,it quieted down so I drove it home, engine light came on so I had it diagnosed, was throwing a bad injector code,would that cause this to happen ? It seems to be running fine now
@sk8erkid14392 жыл бұрын
If you haven't done this yet, likely fuel pump relay starting to go bad - verticalvisions.com/en/content/14-tipm-fuel-pump-relay-solutions
@player51onthenet Жыл бұрын
I have installed some 50lb fuel injectors in my 2014 ram 1500 5.7 and it runs but around 80mph the rpms are staying at 4000 and won’t go any faster . I am running a 91 oct tune in it . Would I just need a new tune for the new set of injectors
@jadenbrijalba18232 ай бұрын
Yes of course 😂 get with a tuner
@kjohns686 жыл бұрын
Leave your door open when tuning. System does not do a complete shutdown ... when you turn the ignition off with your dot closed you’ll notice you dash and stereo are still on.......
@BoostedMotorsports6 жыл бұрын
I'll give it a try! 👍
@kjohns686 жыл бұрын
Let me know.. I used to have the same problem
@BoostedMotorsports6 жыл бұрын
Was this with hp tuners? Where did it fail?
@kjohns686 жыл бұрын
BoostedMotorsports yes HP TUNERS FAILED same place as you.
@wadetaylor31954 жыл бұрын
My 2013 Ram doesn’t have a schrader valve. How would you check fuel pressure??
@joshgsxr10004 жыл бұрын
I ran into the same issue, and believe you cannot check it unless you splice in and add a Schrader valve.
@wadetaylor31954 жыл бұрын
joshua stephens I found out that it has a fuel pressure sensor so the pressure is read through a scan tool.
@MarcoWashington5 жыл бұрын
What map sensor and injectors did you use
@BoostedMotorsports5 жыл бұрын
They came with the Procharger kit 👍
@jnichols3rd6 жыл бұрын
I've not had a problem with my diablo sport intune v3, transmission wise what is the exact problem you were having
@BoostedMotorsports6 жыл бұрын
Man that sucks to hear! Its pretty common with the transmission tuning to be a bit flaky!
@txgaspimp93216 жыл бұрын
Moving on up
@BoostedMotorsports6 жыл бұрын
2 steps back though! Another update hopefully tonight. Stock injectors and map sensor have to get swapped back in 🤦♂️
@tunafish32166 жыл бұрын
Why do you have to pull the fuze when you disconnect the battery ?
@hunterb80166 жыл бұрын
Tuna Fish you pull the fuse so the fuel pump doesn’t try to pump when you’re starting it. He was just trying to get the fuel out of the injectors so he didn’t have a huge mess.
@BoostedMotorsports6 жыл бұрын
Yeah the procharger instructions tell you to disconnect the battery before yanking the fuel pump fuse. I personally think it's probably unnecessary to disconnect the battery first but you never know with these computers it could freak out.
@jeremyyeppez33055 жыл бұрын
What is the manuel you are using
@KINGBAND096 жыл бұрын
Performance Fuel injectors? Why or why not?
@BoostedMotorsports6 жыл бұрын
Needed these for more fuel with boost 👍
@KINGBAND096 жыл бұрын
Oh ok! I was asking if they were performance ones. What brand are they?
@jacobkfrick109 ай бұрын
What book is that bro
@mexxibaby13333 жыл бұрын
Just changed the spark plugs & coils on my Ram sport. I keep getting a misfire on cylinder 3. Anybody else had this problem??
@Jerrden3 жыл бұрын
Try swapping the injector on cylinder 3. Injectors are really easy to swap, I didn’t even disconnect the fuel line.. there’s enough play to get by. Just make sure you have towels or something to catch the fuel that comes out.
@juniorortiz94472 жыл бұрын
Do you still have the links for the spacers and also hard ware ?
@vicer77 Жыл бұрын
did you ever find any info on these?
@TejasToolMan6 жыл бұрын
hurry up man im ready to see you burn some tires ;)
@BoostedMotorsports6 жыл бұрын
Same!!!
@dereclara64296 жыл бұрын
First!!!!!!!!!
@BoostedMotorsports6 жыл бұрын
Hell yeah!!! Notification squad 🤘🤘🤘
@felipe68184 жыл бұрын
Mopar = more parts
@terrylee7732 жыл бұрын
No this is normal nothing major I have 171,000 miles on my 5.7 without a full tune up a 30o s the v8 is a good motor