How to install a 2017-2018 Hyundai Elantra rear bumper cover

[@ReveMoto]

Thank you for stopping by and watching our video. We are here to help you fix your car! Where To Purchase: bit.ly/elantrabumpers If you need any other high quality painted auto parts, visit us here : www.revemoto.com

[@birdyvidsandstuff]

Thank you for your videos! Some tips from doing a swap today. The taillights will be the biggest challenge to remove. Jiggle a lot and also pinch those two white tabs inside the car the fat way as this will help release the locking mechinism that they utilize. Another warning (did this today), since you're wiggling and taillight you may break the bulb/s! So just be warned and TEST this BEFORE you reassemble the taillights (I made this mistake and had to take it out AGAIN). Make sure you are pulling the taillight in the direction of the bolts in the car as well. Otherwise the actual bumper removal and install is a cakewalk.

[@ReveMoto]

Great tips, thanks for that! The tail lights are a bit difficult to get out.

[@3rdRockFTS]

For me, the taillights went very well, no time at all, my issue was with the two push pin clips behind the facade on either side of the lower trunk area which if you look at in the video they look like hooks! They weren't addressed in the video but are quite a challenge when trying to remove and replace. If your Elantra is equipped with sensors, there's also a wire attached to the back of the facade which has to be unhooked before removing the facade.

[@MsHale-fz4sh]

Nice video. What are the part numbers to the push pins that secure the bumper and the screws? Please

[@3rdRockFTS]

So if you have the lower reflector lights and lower black trim panel, wouldn't it be best to install these items on the fecade before installing it to the bumper?

[@ReveMoto]

Yes best to install first on bumper then put on car

[@tylerbrown7713]

What are the pieces called when you screw in the bottom side at 7:28?

[@ReveMoto]

That would be the screws for the fender liner, or the screws that attach the fender liner to the rear bumper. The dealership guys should know what to look for. They are small screws.

[@issaiahspencer5594]

How do you remove/install the lower grey valance ? (On rear bumper)

[@ReveMoto]

If it is like most lower valances and the Hyundai Veloster, you just unclip the lower valance by pushing the tabs. There should also be a couple screws holding it on. I hope this helps!

[@uncrownedking5106]

I want to upgrade the look of my 2017 elantra by changing the front and rear bumper to the sport edition ones. I was wondering if they would fit or not?

[@ReveMoto]

Thank you for watching. We always recommend doing your own research. There are only one hood and fender, so the bumper will most likely fit. You will need to make sure you have the connectors for the daytime running lights on your harness. You would need those and the fog light covers. The grille looks to be the same shape, so that may also fit too. Let us know if you have any questions!

[@BleuMiru]

Yooooo I’m tryna do the same thing, I wanna change my 2018 Hyundai Elantra bumpers to the sport bumpers

[@Amrit_SZN]

Yoo broo uk whats the price for 2016 kia cerato back bumper i really need one

[@ReveMoto]

Unfortunately, we only sell within the United States. I believe the Kia Cerato is possibly the same as the Kia Forte here in the states. We can only get this bumper (OEM) from our partner Kia and it runs around $900 for it to be painted and shipped (in the USA). We wish you the best of luck!

[@Amrit_SZN]

@@ReveMoto ohh thanks, uk the price used though?

[@ReveMoto]

@@Amrit_SZN No sir, that is for a brand new part painted and shipped. We only use high quality materials to ensure a perfect match a life long paint job.

[@G35Tim]

I have a 2017 Elantra SE and I need a new paint matched rear bumper cover and all mounting hardware. Do you guys sell em?

[@ReveMoto]

Hi Timothy, Yes we can definitely source it all out for you. Go visit our team at www.ReveMoto.com. Our live agents will help you out.

[@tylerbrown7713]

Where can you get bumper push pins

[@ReveMoto]

You can buy them at O'Reilly, AutoZone, but they are usually the same price as the dealership. We recommend the dealership because they will give you exactly what you need, whereas the stores are just generic pins. Thank you for watching!

[@kpsingh345]

Are there any screws for reflectors or just the clips? Can we replace the reflectors without removing bumper.?

[@ReveMoto]

Possibly but we recommend you take the bumper off completely. This customer was going to install the lower valance and reflectors themselves. So, we didn't get a chance to do it. In my experience, the reflectors are held on by one or two small screws. It might be possible to do if you loosen the bumper at the bottom and sides. This way you can have some room to get your arm in with a short philips screw driver and remove/install the reflector. But if you do this your pretty much removing 70% of the bumper. Also you might damage the bumper up top if you push to hard with the bottom loos and the top secured. Let us know how it works out. Thanks for the question!

[@laflamescott8688]

Hey I was wondering do you have videos on installing the reflectors?

[@ReveMoto]

We do not because this customer bought her reflectors somewhere else. However, I believe they just snap into the bumper and are held on by 1-2 small screws. I hope this helps and thanks for watching!

[@user-bm9dt9jv2e]

This video is perfect , dude . Thanks

[@ReveMoto]

Thanks for watching! We're glad we can help. Cheers!

[@rickjurado2398]

Your vid states rear bumper 2011 to 2015, but the caption for the title states "how to install a 2017 -2018 Hyundia Elantra rear bumper cover" is the 2018 the same as the 2011 - 2015?

[@randyu8688]

I know, confusing

[@derrianterrell]

How do you remove the bumper

[@ReveMoto]

Our customer had her bumper ripped off. We don't have the removal video. BUT, just play the video in reverse to see how to remove the bumper. I hope that helps, thank you for watching.

[@LIVESxFICxTION]

What about those 2 brackets sticking out the absorber? Do they just sit there? Is it even necessary to have them? Please answer my question thank you

[@ReveMoto]

Hello! Yes, those brackets sticking out of the absorber are necessary . The rear bumper slopes down under the tail light and bulges out, and those brackets support the rear bumper. The brackets are there for a reason, so we recommend replacing them. Bumper brackets can be purchased at your local dealership and they usually run from $30 and up. You can certainly try it without but Hyundai has there for a reason. I hope this helps!

[@TacoFlavorKeeezes]

Where are you located? I need help please

[@ReveMoto]

We are located in Houston, TX. Please let us know what you need help with and we'll provide the info.

[@lynetteazar4477]

I need clarification on the hardware needed. My situation is same as this video.

[@Ke_YAH_nuh]

Where was the mounting hardware purchased?

[@ReveMoto]

Hello. The little black push pins and bolts can be purchased at your local dealership or autozone/orielly stores. If you have broken bumper brackets, you can get those at the dealership as well. The bolts and push pins tend to run about a dollar a piece or less and the bumper bracket can be $30 and up. I hope this helps!

[@greatgatsby4042]

Plz. Can you repeat recording the same clip but in details

[@ReveMoto]

What issues are you having with the removal/install? I can help you.

[@shortygado9478]

Do a sonata one 2018

[@ReveMoto]

We'll do our best to get a 2018 in for a video. In the meantime, we do have the 2017 model and it may be very similar. kzbin.info/www/bejne/gHmug2OefZumia8

[@juanvenegas6238]

Is it necessary to have the fender liners where the bumper clips to? Will the bumper fall of while driving like 75 to 80 mph or will it be just fine

[@ReveMoto]

No bumper won’t fall off as long as it’s bolted on side, top and under side. I do recommend replacing the fender liner for debris issues

[@bethaniejernigan9955]

Thank you for providing the link to the bumpers. I've been looking for a bumper for my 2017 Elantra SE

[@ReveMoto]

Thank you for considering us. Please chat us up on our website, call 281.561.5300 (9am-5pm CT) or email us at [e-mail]. We're here to answer any questions you might have.

[@roku4668]

will the elantra sport bumper fit on this variant?

[@enchonggo5688]

how about front bumper

[@ReveMoto]

We are trying to get one in locally for the front bumper but It seems a bit hard to find a willing customer.

[@mctgaming9211]

I bumped into a wall the other day with my moms car only damage was to rear bumper. I get why she mad but the rear bumper isn’t that much and this is so easy to do. Idk why she had to tell her insurance

[@ReveMoto]

Hi! Even though she told her insurance about the damage, she doesn't have to fix it through them. Going through insurance may cost a bit more and raise your moms insurance premium but usually you don't have to deal with anything, except paying your deductible and picking up your car when it's completed. Let us know if we can help!

[@Rabbit19964]

ReveMoto - Pre-Painted Auto Body Parts how much did it cost to replace this bumper? I have the same problem but I can’t find the replacement parts anywhere to do it myself

[@ReveMoto]

@@Rabbit19964 Hello Sir. I will link our brand Hyundai Elantra bumpers page below. If the damage isn't too bad, you may be able to pop the dent out. If the damage includes cracks and, or removed paint, you'll need a new bumper. We recommend to re-use any clips/screws and brackets that you may have. If you have any questions or concerns, email us at [e-mail], visit our website and chat with us, or call 281.561.5300. I hope this helps! www.revemoto.com/collections/hyundai-painted-bumpers/model_elantra

[@ramonfernandez8207]

What size are the Nut Grommet ?? I’m trying to find them

[@ReveMoto]

Hello, and could you time-stamp or tell me where they go? The nuts for the tail light were 8mm, and the bolts were 10-12mm for the bumper (top & bottom). I don't know the size of the push-pins but you can get those from the dealership for the same price as AutoZone, and they'll be the exact ones you need.

[@MacAutoDiag]

Where's s the removal process? The heck kinda video is this

[@Mahan_KC]

Yes but how did u take it off ?

[@ReveMoto]

It’s actually pretty easy. Bolts on side and top. Then push pins down below

[@jakezickuhr3948]

they didn’t take it off or do the install 😂😂 they had someone come in an explain it to them. thats why when you go to install your bumper, this video is useless!

[@coffeeis4closers]

Good information, thanks. And as you probably know you have an amazing body!

[@ReveMoto]

Glad the video was helpful!

[@andrewseto07]

This is not 2014-2016 year model elantra

[@ReveMoto]

It is. The bumper fits a 2014-2016 model Elantra's. The 2011-2015 is the fifth generation but it the 2014 model received a face lift changing the fog lights to an "L" shape and placing the reflectors on the rear bumper instead of on the lower textured valance. As well as the face lift, 2013-2014 GLS models changed to the SE model and in 2015 and 2016 saw new changes and upgrades to the SE models, respectively. In February of 2016 Hyundai released the sixth generation Hyundai which is the one we see today. That one also received a face lift for the 2019 models. I hope this clears some things up. Have a great day! en.wikipedia.org/wiki/Hyundai_Elantra#Fifth_generation_(MD/UD;_2011%E2%80%932015)

[@hemipowersrt6773]

This is a 2017-2018 year model

[@ReveMoto]

@@hemipowersrt6773 you are right. The bumpers look almost the same except for the slight indention under the tail lights and the slots for the diffuser. We will make the proper changes. Thank you!

[@xo-CLASSIC-ox]

Lol them prices hella high

[@ReveMoto]

Hi David, we use high-quality paint and put great effort into making sure these parts come out to our expectations, from using the right vendors to having the right people on our team. You'll know you can count on our parts to come out as expected.

[@rodneydavis8631]

The rear lights are hard to take off

[@ReveMoto]

They sure are. We have another video showing you how to remove them, but we did have to pause it to get someone on our team with a stronger grip to pull it out. And, we still just did it by hand! There have been some great suggestions on how to do it easier in the comments section of that video (here: kzbin.info/www/bejne/jmXJnYl4p9x8bpo) So definitely let us know if any of those suggestions work!

[@fjccommish]

Terrible. Suddenly, the lower bumper is removed. How can anyone follow when you cut to things already done?

[@ReveMoto]

Hello! Our customers bumper was ripped off. So, we didn't have one to take off. If your learn, how to install it, you can definitely take it off. Have a great day!

[@fjccommish]

@@ReveMoto I see. Thanks. Mine is cracked in places, mostly off on the left. There isn't a bottom separate piece.

[@ffqc-prado9747]

That’s 2017-2018 actually....

[@ReveMoto]

Yeah, it's in the title. We didn't realize until it was too late. 🖖

[@donaldkeyser-vg6dk]

Says 2017 to 2018 what year

[@jakezickuhr3948]

hilariously bad video! completely wrong and just a flat misrepresentation of how it’s done 😂😂 what a joke

[@ReveMoto]

Must of been a slow day in your life today. Hating was your choice of drink

[@ericsmith1782]

This video left plenty things out , lame !

[@ReveMoto]

We're sorry you feel that way. We couldn't install the lower valance or reflectors. Our customer had those to install herself. We also have a video on how to remove the tail light on our channel. Take care!

[@isabellamichalek7705]

​@@ReveMoto if I'm trying to install the rear valance, and I have the necessary clips to do so, should I just go for it? I've had no luck finding a tutorial on this... Is there another name for the valance? Your video was great!

[@MacAutoDiag]

Audio sucks

[@joejones6968]

Fail. Terrible.

[@ReveMoto]

We're sorry you feel that way 😥.