How to install a 360MM AIO Liquid cooler Ft. MSI MAG Coreliquid I360

[@Bulu2898]

Thanks 😊 followed step by step. And the outcome was awesome 👌.

[@ahmedalassaadi1847]

Thank you so much for this video

[@CrazyTechLab]

*Timestamps below* Thanks to @MSIGamingOfficial for sponsoring today's video and sending over it's fantastic MAG Coreliquid I360 that we used here in our cooler install guide. It makes a perfect starter cooler for anyone using one for the first time. Buy the cooler amzn.to/3T9qSPx Buy the case amzn.to/4cPnPD0 Buy the motherboard amzn.to/472UdAV Buy the processor amzn.to/3T8IhHX Best cheap 4TB SSD! amzn.to/3XkQfAi If you found my videos useful you can always buy me a coffee! 👉www.buymeacoffee.com/crazytechlab Check out my Amazon shop with all the best products! 👉 www.amazon.com/shop/antonyleather www.paypal.com/donate/?hosted_button_id=P8PHVM6V3UAQS Subscribe: bit.ly/2QYAZK9 Instagram: instagram.com/crazytechlab Facebook: facebook.com/CrazyTechLab Twitter: twitter.com/antonyleather Timestamps 0:00 Intro 1:12 Check case compatibility 5:04 Liquid cooler components 14:16 Step by step install on AMD and Intel motherboards 28:50 Install the radiator and pump into your PC 44:28 What it looks like when it's done

[@N77O98]

Hey so we have to connect pump power connector to pumpfan socket right ? Then 3 pumpfans to cpufan socket? And RGB to +5v socket right? Because my motherboard have 2x +5v jrgb, 2x +12v jrgb sockets .. and then what is the use of +12v jrgb sockets? And cabinet pre-installed fans mentioned 12v fans ... Please explain this

[@CrazyTechLab]

@@N77O98 Yes ideally to AIO pump header and the fans to your CPU header. Pump should run at max speed with AIOs usually and the pump header usually defaults to that. The 12V RGB headers are for one colour 4-pin LED strips. 5V/3-pin you can change the colour of individual LEDs within the device and create multicolour/rainbow effects.

[@giacomovaninetti6976]

Thank you so much!!!

[@B_r_u_c_e]

Very good. Thank you.

[@BruceArtwick]

...and I've just realized I will install the GPU after I fix the AIO when I get one.

[@_N4VE_]

yup good call to do all the fans/cooling first before the GPU and other things that will take up workspace 👍🏽

[@BruceArtwick]

Wouldn't it be easier to lay the case down? This way you wouldn't have to hold it with one hand. I understand that you had to do the filming at the same time, but when not, it wouldn't be that awkward.

[@SaschaRobitzki]

Yeah, I usually lay it down as well.

[@ivopearce]

how do i install a 360mm when the cpu pump header is in the way

[@cdavidmur]

I just got this cooler and set it up no problem but only 2 fans are spinning? I dont get why i took it back out and checked but nothing seems to be wrong i disconnected the connector and plugged it back in but no luck, any suggestions? TIA

[@altonkriel]

Intel Black Bracket on back of MOB, after installing screws there is some play in the bracket, is this normal? - or am I missing something?

[@nishaanp7882]

Are the fans that are preinstalled on the radiator setup as intake or exhaust?

[@GOLDDIGGERPRANKSTV]

Is The Wire On The Radiator Connected To The Radiator Or The Fans? THANKS

[@CrazyTechLab]

It’s connected to the fans but it’s very well tidied out of the box so it looks like it’s attached to the radiator. They’ve done a really good job!

[@GOLDDIGGERPRANKSTV]

@@CrazyTechLab Thanks Man, Just One More Question, Could I Change The Fans On This Product To My Own Eliminating That Cable For A More Clean Design?

[@CrazyTechLab]

@@GOLDDIGGERPRANKSTV Yes you can remove them. The radiator is separate to the fans and cables.

[@GoosAbsorbs]

Does thermal paste come with it

[@ahmedalassaadi1847]

Yes

[@hops6326]

How did u get the Argb to work?

[@CrazyTechLab]

Connect the coolers RGB connector to a 3-pin RGB header on your motherboard 42:27 Then use your motherboard's RGB software. Or you can buy a third party RGB controller and use that

[@hops6326]

Got it thanks.