This video walks you through the steps of performing a fresh installation of a deadolt. www.norcallocksmith.com
Пікірлер: 38
@norcallocksmith12 жыл бұрын
The other method for marking the hole in the jamb is as follows. First install the bolt into the door. Next put some lipstick or grease on the end of the deadbolt, where it comes out the edge of the door. Then fully close the door and extend the deadbolt so that it makes contact with the jamb. Drill a 1" hole directly in the center of where the mark was made. That's it.
@Angelus21728 жыл бұрын
It is a great educational video for those who need a bit of remembering of how to do this. Thanks!
@Jontiac12 жыл бұрын
wow, thanks so much for making this video. I could have never figured this out on my time. Time to head to the hardware store to pick up some new drill accessories for this type of job!
@skiplathrop24237 жыл бұрын
There were some great tips in this video! Thank you very much!
@Mezgur9 жыл бұрын
was this recorded in a tunnel?
@superspecialty51692 жыл бұрын
Out of the several vids re: doors & windows I’ve been researching, you’re the first to be prolific with saying “ahs”!. With that said, it’s time to say good bye
@executiverailz3 ай бұрын
You are right, I never noticed that before but I did say “ah” a lot. Time to brush up on the acting classes.
@Ahennem13 жыл бұрын
Nice step by step video. Keep up the good work.
@mprrx7 жыл бұрын
Thank you. Very detail. You just forgot the alternative way in order to install the strike plate....found down below about the lipstick!
@bobbymuertero9 жыл бұрын
Great video, thanks !!
@vskkgaming11 жыл бұрын
good video, very informational and helpful....
@dahur8 жыл бұрын
Very informative....thanks.
@bluedb1010 жыл бұрын
very nice video. thanks
@raymondhoguelll20447 жыл бұрын
What size drill bit do I use I guess a little smaller then screw would be ok
@DesoINC2 жыл бұрын
Good video
@wbocxe10 жыл бұрын
Great!
@tha_mogul_music Жыл бұрын
Thanks ‼️
@85kingz8 жыл бұрын
thanks for the help thumps up
@itsmenotyou57997 жыл бұрын
good job
@vavavee7 жыл бұрын
Hello, I just installed a Gatehouse deadbolt lock. Everything looks good and seems ok, but the key will only release if it is in 'locked' position. Also, once the key is out I cannot turn the thumbturn. Can you advise me? Thank you.
@joshreeves94986 жыл бұрын
vavavee most likely have your screws to right in your knob.
@shonuffisthemaster7 жыл бұрын
decent video but theres a few problems i can see. usually the allignment on those latch plates is pretty precise or they wont latch right, the sort of general hold the mechanism in the hole and outline it i dont think is really precise enough. also angling the screws like that, even though its nice to get a stud, will mean they wont be flush with the plate
@executiverailz3 ай бұрын
If you put the deadbolt in the door you can put lipstick on the end of the bolt and close the door and throw the bolt. This will show you exactly where to drill your hole in the jamb.Screws won’t be flush but small price to pay for a secured door. Its necessary for security to hit a stud. Otherwise one would want to use a heavy duty strike that allows the 3” screws to line up with stud straight on.
@RobinHood-ih6se4 жыл бұрын
I like this video. What is the name of the tool you're using at 6:51?
@executiverailz3 ай бұрын
Latch guide punch. It’s not necessary if you close the door you can use a sharpie and draw a circle on the jamb through the 1” hole. You’ll want to do it from both sides in order to get a good idea where the center is.
@judyhite50363 жыл бұрын
I plan to replace an old snap lock on an old wooden entry door with a deadbolt lock. My problem is the current opening for the lock is only 1". Could I make this opening the required 2 and 1\8" with a hole saw????
@executiverailz3 ай бұрын
It would be hard to do without a jig. Your hole saw will want to move around a bunch.
@navy147811 жыл бұрын
Nice
@raindogred11 жыл бұрын
ever heard of a door wedge?
@garlicdawg10 жыл бұрын
how do U know if its 2 3/8 or 2 3/4...if it has no template.....?
@garlicdawg10 жыл бұрын
Stuart Krantz thnx for info....so if I throw the lock across the room....i will then know what size it is......? not following...mine does not show any size and not quite sure what template to use....I think the 2 3/8 is the more std size so will go with that....thnx....
@norcallocksmith9 жыл бұрын
garlicdawg the standard backset for residential is 2 3/8" the standard backset for commercial is 2 3/4 most locks are able to accommodate either.
@ms97714 жыл бұрын
at all was not helpfol for the problem had, why ca not keep the lock bothside match to stand and keep nail in ?