How to install a door closer, top jamb installation video by Tell Manufacturing
Пікірлер: 74
@irfanahmed67443 жыл бұрын
I don’t like because you didn’t mention this measurement....🤔🤔
@ivaerak2 жыл бұрын
2:10 I love how the main arm hits the door frame both times when passing it. Happened to me as well. Displacing the entire unit for a few mm lower was out of the question, so my only option was to loosen the bolt with the washer on the main arm and lower the main arm/shaft a bit by hand, so it doesn't hit the door frame every time.
@Speeddemon36 жыл бұрын
That bang bang you hear when he opens the door is the elbow knuckle striking the top of the door frame. Probably better to adjust to your door frame with more room at the bottom.
@afaqdurrez55522 жыл бұрын
Awesome. Well explained for those who want to install main pump on outer frame of door.
@silencedconversations9 жыл бұрын
Good man. I wish i saw this video 3 hours before
4 жыл бұрын
Estou no Brasil, trabalho com esquadrias de alumínio a muito tempo, mas nunca instalei uma mola aérea do lado de dentro de uma porta que abre para fora. E preciso instalar uma amanhã, não tinha a mínima idéia de como iria fazer, obrigado pelo vídeo. Like certo
@saifahamad47992 жыл бұрын
ap
@waynesmith-hw5sh9 жыл бұрын
Thanks mate, I really did need to see your video before I made a mistake, i didn't see your video and did make a mistake,, thanks wayne,, Wales UK
@roge7158 жыл бұрын
Can you please add the measurement where the holes need to be?
@erroln7359 Жыл бұрын
Was also looking for that measurement.
@maximumwoof866210 жыл бұрын
you didn't say that the jamb/header was wood or metal... also, you said drill and tap for 1/4x20 machine screw threads... this assumes that the header is, 1) not thin aluminum or hollow sheetmetal stock. these should only be drilled and tapped for such if there are backing plates behind the sheetmetal such as 3/16 inch thick. for thinner metal mounting surfaces, one should use the large sheetmetal thread screws to avoid pull out. again, you 'didn't say' !
@paulrobertsonssimon79057 жыл бұрын
the best of me t
@j8ke9376 жыл бұрын
maximum woof you didn't say you are a complete tool but we gathered that anyways. Again you didn't say.
@maximumwoof866210 жыл бұрын
also, the crescent wrench was flipped the wrong way. the turning pressure should not be on the 'movable' jaw side..
@OttoByOgraffey5 жыл бұрын
Running on empty. Anybody catch that?
@WeeJamonP27 жыл бұрын
When people always open your door but never close it on their way out. That's right, im looking at you, parents! I wanted to see how this was done before i get one. Nice video
@edsonfarine8101 Жыл бұрын
Excelente!!!! Apesar de não entender o idioma, Entendi a instalação!!! Pois não achei abrindo pra fora!!!(nativo)
@samirchavi51216 жыл бұрын
I just instaled one today but I don't understand is why I can't control the speed ......the manusl says that depends on what side are u want to instal it and you need to adjust the part where the arm goes mounted acording to the marks ......but I don't know if thats the problem
@allycarter41515 жыл бұрын
What are the measurements from the door jam and door?
@allycarter41515 жыл бұрын
The measurements that came with the instructions are 220 and 95 etc...What measurements are these and do I convert into inches?
@allycarter41515 жыл бұрын
* how do I convert in to inches?
@abobas67732 жыл бұрын
You should be a little be more detail and don't move too fast!. Show
@dadduorp Жыл бұрын
Very well done-this helped a lot! However, I want to install one of these on a door that leads to basement stairs but there is about 2” of decorative moulding trim around the doorframe. Can one of the components be lowered/raised to compensate for the height/clearance needed?
@ginesramosvalenciano96993 ай бұрын
En Español
@ramhunter45647 жыл бұрын
McLovin
@FooJaymee Жыл бұрын
Hi, does anyone knows the measurements?
@joshuamcdonald62847 жыл бұрын
Are these measurements appropriate for different brands and models of door closers, or are they specific for this model?
@benorton13337 жыл бұрын
We want to put the Ryobi on the top jam of the door. Will it push the door shut??As opposed to pull the door shut?
@lordvega3287 жыл бұрын
You saved someone's life today. I lost my mind listening to this damn door slam, you been a great help the door now closes perfectly thanks a lot keep up the good work
@andrewgaurdafe67286 жыл бұрын
Good pm sir tanong lng po ano Po ba ung ping ka iba Ng hydraulic door closer sa automatic door closer salamat
@paivaaxel66866 ай бұрын
Michas gracias
@user-wl6ks5in6j7 жыл бұрын
это лучшее объяснение . хоть я английский и не понимаю , но всё понятно . а я то думал , почему у меня дверь хлопает по косяку ... вот оно в чем дело - колено должно быть перпендикулярно плоскости двери!
@karimullabaig41706 жыл бұрын
What mechanism is used in this one..any one please reply me
@mbtran3216 жыл бұрын
Thank you for the video! Had to replace and adjust! Perfect!
@roberthofberg1534 жыл бұрын
GREAT!! So helpful! Thanks guys!!
@19jaredbarsuglia8110 жыл бұрын
Almost got it right. Give a little preload to the arm, and on regular and top jamb installations you can mount the armature to the closer body before mounting the closer. This will allow for the proper preload, and elimination one step. Thanks for the video
@JLD90210 жыл бұрын
thats how I do it, assemble arm to closer before mounting it to the door, but most follow the instructions word for word, and prefer to put the arm on AFTER the body is up. -Jess the door closer doctor
@SunnyCalifornia1239 жыл бұрын
Great demo teaching man! I got a problem....i.e. to keep the door stay "still" or stationary when it is "fully wide open" (such as to move things through the door before it closes up automatically as in normal case). After moving the stuff thru the door, then the door will be manually closed after I pull it inward to activate its automatic closing action. How can I do it? Thanks for your help!
@19jaredbarsuglia819 жыл бұрын
Unfortunately to accomplish what your looking for, you would need different parts all together. One option would be a "hold open" arm, this is adjustable as long as the closer was originally installed correctly, at the proper degree of opening. Also, not all closer bodies have a compatible hold open arm assembly. If the opening is fire rated, it would be against fire code to have any hardware that impedes a positive latching motion. In some cases you can put a delayed action closer on. This has an extra adjustment that delays the closing of the door up to 30 seconds. This requires a whole new closer assembly. Hope this info helped
@uvaishabbasi7867 жыл бұрын
good
@rennbayshipping60658 жыл бұрын
you rock dude, easy as can be after watching this.
@ishtiyakaluminium2 жыл бұрын
Very good information
@pedrosergio2911 Жыл бұрын
vERY GOOD
@markdask6 жыл бұрын
Nicely demonstrated :)
@rafaelfaria56392 жыл бұрын
Congratulations
@serenerelax23344 жыл бұрын
Great!🙏
@krishnamoorthy7279 Жыл бұрын
Nice
@MarioLamagrande2 жыл бұрын
capo
@lakhabawa70423 жыл бұрын
Hello
@sultanm96626 жыл бұрын
plas araby
@heliooliveira36234 жыл бұрын
Good.
@rodolphforbes94138 жыл бұрын
This is useful tips
@azaruddin449847 жыл бұрын
Good gide
@RanjitSingh-dl1wi6 жыл бұрын
Well done good job 👏
@birdscastle8 жыл бұрын
thanks
@코남-r6k7 жыл бұрын
굿
@jantjedefretes52816 жыл бұрын
Ampli fayer kenwood
@IceAge200178 жыл бұрын
good. thanks.
@sultanm96626 жыл бұрын
Good manGood man
@jackdunne96827 жыл бұрын
My
@ebriheemalamrani90004 жыл бұрын
🌹👍👍👍
@MAGNETIC-COMPASS7 жыл бұрын
useful tips thank you very much
@vladimirturudija392411 ай бұрын
This is the best tutorial for this job i have found on internet. Good job
@eugenerudas494 жыл бұрын
М-О-Л-О-Д-Е-Ц... очень помог!)
@chanaguerrero57624 жыл бұрын
My door push outward towards the exterior, can this be mounted on the exterior side?
@ivaerak2 жыл бұрын
no, it mounts also in the interior, you just need to switch the side of the main unit upside-down. Should be in the instructions in the box.