How To Install A Gas Fire Pit

[@mowman7777]

Use hardware cloth to cover the inside of the vent holes to keep critters out.

[@gregchick2492]

He is a bit "dry" but hey, he's clear and accurate and professional. One option I have seen is a black iron ring instead of a stainless steel ring. The black iron has holes on top/bottom, not the sides like the Stainless steel ring. Too often the black iron ring is installed with holes facing up. The dust.rain and debris get in holes. Instructions I have seen say holes down. This is not a kitchen stove burner, and flame / heat go up. Can someone feedback any experience on black iron rings and hole direction? Another issue is LPG, heavier than air, allowing gas to puddle below ring and leak out sides of pit at bottom... again, thoughts?

[@williamd2451]

Great tutorial!

[@ewingoutdoorsupply]

Thank you!

[@Howie875]

Great video but some clarification is needed on the cross ventilation, Natural gas is lighter than air and will not collect in the bottom of the pit if the flame goes out. You can fill thin plastic bags with natural gas and they will float away. Propane, on the other hand, is heavier than air and a leak or any other problem will fill any depressed area with propane and if you try to light it in this condition it will cause an explosion. Heard about a house with a propane heater in the basement and when the heater turned on the house was obliterated.

[@BlackZeus88]

Great breakdown!

[@tedunn07]

You are correct in your gas science. However, I think the main reason for having cross ventilation below the burner pan is to prevent any dangerous gas build up should there be a leak in the gas valve, gas line, or any of the gas connections below the pan.

[@Howie875]

@@tedunn07 Hi I agree somewhat with your opinion, but I think that natural gas, being lighter than air, will not collect in the bottom, it will float away just like helium would. Many times, there is not a breeze to cross ventilate an area like this, but natural gas will still float away and not collect in the bottom. The real reason for having ventilation on the bottom would probably to allow the flame to "draft" meaning it draws in what is called secondary air to help the flame burn more cleanly.

[@cameronjuzda7246]

Do you glue the top bricks or leave them. Thanks

[@ewingoutdoorsupply]

You can, but if you glue the top row it'll make it difficult to access the components for maintenance in the future. Thanks for the question!

[@jl456]

Also how tall is this pit and what is the recommended height? I know it's probably personal preference but what does the majority do?

[@ewingoutdoorsupply]

Each of the blocks used in the video (Rumblestone from Pavestone) is 3.5 tall so 14 inches is the pit height. 12-14 inches is common.

[@jl456]

@@ewingoutdoorsupply thanks for the help!

[@coolguy24eric]

I'm putting one of my screened in porch. I'll have about 6-7 ft above the fire pit till you get to the roof. It is screened in though. How important is that 8 ft minimum?

[@ewingoutdoorsupply]

Proper clearance and ventilation are important safety factors to consider. We suggest you check your local codes first. Thanks for watching!

[@coolguy24eric]

@@ewingoutdoorsupply plenty of ventilation. It's a screened in porch. Not sure we have any local codes for outdoor fire pits

[@ewingoutdoorsupply]

@@coolguy24eric Here's a link to the fire ring manufacturer's instructions for installation. The instructions include safety information. www.firegearoutdoors.com/instructions

[@jl456]

Do you glue all the blocks?

[@ewingoutdoorsupply]

You can but it's a good idea to not glue the top row in case you need to access the burner in the future for maintenance. Thanks for the question!

[@hammerdown3876]

nice. i like that burner set up. how do you handle water drainage? Id prefer a metal lid cover vs having to tarp and am trying to figure out how to handle drainage of rainwater that may find its way in. Thanks!

[@ewingoutdoorsupply]

+Hammerdown -Sorry for the late response. The manufacturer does not make a cover for the particular burner system we used in the video. While the disc we used has weep holes to allow water to drain through, it's a good idea to use a cover of some kind to protect the components from the elements. I agree that a tarp would not be the best solution but if you do an internet search for fire pit covers you will find a variety of options for metal covers that might suit your taste. Thanks for watching!

[@DevinSinhaMusic2]

Really nice video! Can tell you all put the work into it!

[@ewingoutdoorsupply]

Thanks Devin! We appreciate the comment!

[@marcygreen100]

Can this be installed over a wood deck?

[@ewingoutdoorsupply]

Hello Marcy, gas fire pits can typically be installed on combustible decks as long a they are installed properly by a professional and do not violate city codes. Thanks for watching!

[@ecl12]

You don't have to cut out a circle in the middle of your patio to pour concrete first?

[@ewingoutdoorsupply]

You may need to cut out a channel if installing a new gas line but it's not necessary to cut out a hole for the fire pit itself. Thanks for watching!

[@MrsPorter410]

Very helpful and informative. Thank you.

[@ewingoutdoorsupply]

You're very welcome! Thanks for watching and for the comment!

[@paulosalazar144]

Great video. I am looking to use a propane tank. Can I use a long propane tank hose (maybe 20 ft or so) to pull from the tank to the pit? What are your recommendations?

[@ewingoutdoorsupply]

Yes, you should be fine with a 20ft line but using a hose may not be advisable. Your best bet would be to consult with a licensed plumber before you begin to make sure your fire pit is safe and up to code. Good luck with your project!

[@leonelblandon7784]

Can you provide a list of all the components you used in detail

[@ewingoutdoorsupply]

Sorry for the late response Leonel. Below are links to the products used. Feel free to contact your nearest Ewing Branch for more information on the blocks as they can vary in color and brand by region. We used Pavestone Rumblestone mini and trapezoid blocks in the video demonstration. Firegear Burner Kit: www.ewingirrigation.com/catalogsearch/result/?q=93553162 Match-Throw Control Panel: www.ewingirrigation.com/catalogsearch/result/?q=93553860 Lava Rocks: www.ewingirrigation.com/catalogsearch/result/?q=93553681 Ewing Branch Locator: www.ewingirrigation.com/locations/

[@mr.g.4339]

Great video. Very informative. Thank you.

[@ewingoutdoorsupply]

Thanks for the comment!

[@kylerutter824]

Do you use the adhesive for the top layer of blocks as well?

[@ewingoutdoorsupply]

You can but if you need to do any maintenance down the road it'll be more difficult to gain access. Thanks for the question!

[@leonelblandon7784]

What components including size did you use for the paver panel

[@jurofly]

Is that 1/2" supply line?

[@nohaterz78]

Do those pavers come in a kit ? If so what size diameter ?

[@ewingoutdoorsupply]

Thanks for watching and for the question! We have a several kits available in a variety of sizes and shapes. These include "ready to finish" units as well as block and fire ring kit combos. Contact your local Ewing branch for more details. www.ewingirrigation.com/locations/

[@roamwarrior]

Where do you find the gas disk?

[@ewingoutdoorsupply]

If you have a Ewing branch near you, you can get it there: www.ewingirrigation.com/locations . You can also find it online here: www.ewingirrigation.com/products/hardscape-pavers/fire-features. Thanks for watching!

[@MattyJBayBay]

Did this company go under? None of their websites work.

[@jimmyzelski7742]

@@MattyJBayBay Works for me. Looks like there are a couple of hundred locations in the US.

[@MattyJBayBay]

Jimmy Zelski it works now, i guess the URL was broken for a little while.

[@RyanReddell]

I'm amazed how a gas fire pit can cost $2,000+ and that is when it is a DIY. What am I missing?

[@roberthiday3342]

nice video, very helpful. thanks.

[@rayvilasuso4717]

Good idea, over price

[@jeffreeds3371]

How to hide that propane tank? Kind of an eye sore

[@ewingoutdoorsupply]

Thanks for watching, Jeff. The tank was only used for demonstration purposes in the making of this video. That said, if you have to use a propane tank for your fuel source, rather than running a natural gas line to the site, there are some products on the market that can help you hide it. A quick google search should yield a few options for you.

[@nicholasabbott6922]

600+ bucks for the kit lmao

[@tylerhall6455]

God this video was boring. Thanks for the info anyway.

[@icallgreens89]

650 just for the burner plate? HAH!!

[@josephnguyen411]

is the narrator an AI bot?