How to install and set up desktop content center | Autodesk Inventor

Detailed tutorial on how to get the Autodesk Inventor desktop content center libraries installed, not a lot more to it than that! #Autodesk #Inventor #Tutorial #3DCAD #Design #Engineering #CAD

[@samp681]

I dont normally comment on videos but i thought you deserved one for this video. I wanted to say thanks, I learnt what i needed to know and i was very entertained at the same time! haha, which is unusual for these tutorial videos!

[@apdevoocomany1179]

Brilliant tutorial I searched on google couldn't find a solution many followed your tutorial and it fixed the content center not found error . many thanks

[@YourMom-ls3oc]

Couldn't get 2020 to load content center for anything. Tried your 7zip workaround. Worked like a charm. Thank you, kind sir!

[@fortresssupplies]

Fantastic Video! I spent hours trying to figure it out on my own and was about to give up. Thank you for your help.

[@shubh3322]

thank you.you dont know how much it helped been at it for couple of hours

[@m0rthaus]

"Back in 'day". Cracked it. Thanks for the video

[@pedroafonso6269]

Hi Neil, hope you are doing well. Thanks again for all the videos. They are very helpful and I have used several of them. I have a suggestion for you. Actually is more a request... :) You have loads of things about the desktop side of Inventor, but it would be great if you could have more stuff about the Vault side of things. I mean... I work in an office in the design department. Not a big one as there are only 3 of us. We use Vault in our workflows and we are trying to centralize things as much as possible so we can keep consistency between us more easily. So, we are trying to install (among other things) the Content Center Libraries and our own Libraries but it's complicated to find useful/filtered information on the subject. It would be great if you could show a bit more this side of things. Like: - How to Setup Vault Content Center (Can I have the Standard Libraries working from our local workstations and Company one from Vault?) - Material Libraries - Relevant options for Vault installations - What should you install to run from Vault and what from your workstation - Paths (do all workstations need the same paths?) - etc... You know what I mean!!! Anyway... It would be really great if you could do some of that. Thanks for all the great videos and Info. Hope you keep this channel up for a long time. Best Regards.

[@scottweiter2477]

Thanks so much. At work it didn't install the content libraries and it's a pain to get admin rights to install anything. You 2nd method saved my ass!

[@HoNau77]

I like your videos. Very good to understand, although I am not an English native speaker.

[@gambarrandom]

wo wo wo nice information capt, thanks, its working!

[@nidhal7184]

Thank you very much for your efforts,, does student version supported with content center,, i have tried both options, but doesn't work,,?! appreciate your help,,,Thnxx

[@davywavy5364]

Hi Jockey thanks for your videos - I find them helpful. I would like to know how you can set up your own libraries that can be used in many projects? These are generally just a parts library and now like the contents where they need to be configurable. Thanks for your help.

[@CaptainCardboard86]

thank you very much for this, super helpful.

[@augustoquispeserrano7050]

thank you it worked

[@harmdeheer]

Thanks a lot. I just downloaded Inventor 2017 proffesional but the content center didn't work. I packed as you say the files out and give Inventor the right path. All my bolts and nuts are correctly back. Now i can use Inventor 2017 with fun as the way i did before with 2016

[@ludmilaaltman257]

Amazing, восхитительно, увлекательно, fascinatingly

[@santamariamike]

You are a legend! thanks for the video

[@mhaji-cf4hz]

thank you. solved my problem.

[@scala5579]

thanks very useful video.

[@jeffstone2601]

amigo Gracias desde Colombia.

[@jan-erikpersson6825]

Thanks! solved my problem

[@chrismerani5330]

At 3:26 you mention that install is greyed out because it is already installed. I have been spending quite a bit of time lately in that screen and I found that the actual "Install" launch button is always greyed out if you have any products maximized. If you select your settings from within that product, then minimize it, Install should be available again.

[@johandegreef3846]

you say there is no link between the library and the part.... once placed. Do you mean the parts are created inside the project folder? You can delete the content centre, and the assembly will normaklly open with all the parts present?

[@davywavy5364]

Great vid as normal Neil. A question me old cocker spaniel. I have done something that now causes a resolve link issue with nuts bolts etc? DOH Is there a way to fix said fault? Cheers from Muppet man

[@Neil3D]

No idea what you've done or where they were so not a lot I can do there! If they're content centre files you can place them again from the libraries, or hunt them down and move them into your current project, but if you've lost all the IPTs then you're goosed, you'll have to re-place them from the libraries!

[@jeffhamilton5697]

I recently upgraded to a new computer. Now every time I try to access content center the response time is unbelievably slow. Could this be related to using existing files that are looking for old search paths?

[@MohamedMahmoud-cj6vi]

Thanks bro it worked

[@aidanarmstrong2236]

I thought I had an issue with accessing the content centre. I use Inventor 2016. When I use frame generator it fails to locate the parts from contents centre library. I have found an issue with Inventor 2016 and Windows 10 version 1903. I think this is now my issue. Is there anyway of getting around this? It looks like Autodesk only fixed the issue on 2017-2019 versions.

[@markdesolate]

Hi Neil, thanx for the vid, but @9:11 there should show up an icon place from content center. My inventor doesn't have that, it says place with an down-arrow and in the menu there's no ' place from content center' icon. What do i do wrong?

[@Neil3D]

Go to the Inventor Tools ribbon bar, click add-ins, make sure the Content Centre addin is loaded (tick both boxes). Whilst you're in there load all the other addins just to be sure.

[@ehsanshahrjerdy9606]

hello.. i re install windows and after that install inventor... after that when i reinstall inventor and open assembly that i designed it past, inventor show window for find parts from content center....how i must find parts?

[@georgiantonov5557]

One question about Inventor frame Generator. Is Frame Generator reading from the same Content Center libraries from the video or there is a separate, I don't know, data base for the Frame Generator? I am asking because after Windows update I was no longer able to create new parts with the Frame Generator. Shortly, it says "The component can not be find in the Content Center"! But, I can still create all the washer and nuts and bolts and so on :)

[@Neil3D]

Yea it does use the same libraries. You can re-install the content libraries from the Inventor download, its a ticky option in the installer.

[@d3ns3n]

Kudos!

[@pasipylkkonen6199]

I dont find, PRODUCT DESINGN SUITE page? I can't find it on my PC, and I can't find it by logging in with the password to autodesk?

[@monikaszak5531]

Sick I do 3D printing at school

[@kuldeeppanchal9125]

my problem is when steup click to mouse then in dailogbox on show "can't find setupUi.dll!" ................................what solution?

[@mdli6586]

Why asked me to install autodesk data management first. Any ideas

[@cecile948]

how to use spare parts downloaded from cbliss.com. I have downloaded it but can't open it in the inventor

[@strangerh1134]

hey, very helpful your video! always thank you and thank you. but. I'm not good at english. so I understand only 10~20% what you speak. maybe more low percent. but. but It's really need for like me. and thank you.