How to Install Center Snorkel on Honda Rancher, Foreman, Rubicon

[@863masonn]

can you guys make a video on what to dielectric grease?

[@DrewFowler-gr8rt]

Will I need a adapter for a wild boar rad kit

[@Justin_6_]

so do I have to have a rad kit for the center snorkel kit to work?

[@Wooahchris]

I just ordered one of yalls radiator relocate kits with the center snorkel bracket. Should be in tomorrow. Ready to see how it turns out.

[@vesselpowersports]

Lets goooo! We definitely appreciate the support!

[@Wooahchris]

@@vesselpowersportsI thought about taking off work today and waiting on the mail truck 😂

[@samuelbrown8690]

@@vesselpowersports How long is the flex pipe and vent hoses yall use in the kit

[@itzcuefn]

What size pvc pipe do yall uss

[@buxndux9667]

Can you possibly do a video or a product to help snorkel a Honda recon 250?

[@vesselpowersports]

will be pretty much the same exact process

[@Stuckin330]

Yo them plates you put in that airbox it’s best to find sum neoprene washers and use locktite on that bolt becouse I’ve seen them come loose . Or put sealer on that bolt an does the same thing to hold that nut from coming loose . Had it happen few times an that’s the fix for people that don’t check on that bolt and good call on the 90 on top of the snorkel pipe to keep water out . Lol seen people run without and wonder how water or mud gets inside . Also I’ve put a vent cap with holes to prevent mud or rocks getting in there sumhow just need to make sure it’s got enough holes to breathe threw

[@tannerbrooks6844]

Seen ole Jackson on this machine this weekend at boggin lol

[@Frizossd]

What is the cuppler that goes into the air box?

[@vesselpowersports]

1.5" PVC Cuppler

[@MasonRegan10]

How long are the 2ich pipes that go into the other 45 and the cuppler

[@MasonRegan10]

Connected to the riser

[@vesselpowersports]

2-3"

[@MasonRegan10]

How long is the pipe that goes into the air box?

[@vesselpowersports]

about 2.5"

[@StevenAllen0717]

What size vent line is that? I already got the stuff for a homemade snorkel except for vent lines

[@vesselpowersports]

5/32 and 7/32

[@StevenAllen0717]

@@vesselpowersports preciate that man

[@samuelbrown8690]

@@vesselpowersportshow long are the vent lines?

[@Flythecontrollerplayer]

Do I need the center snorkel bracket

[@vesselpowersports]

Yes

[@RElliott17]

what size is the hose and pvc fitting y’all use?

[@vesselpowersports]

1.5" hose and 2" pvc

[@donivant2822]

I want everyone to notice how there is no powerstearing unit on this bike that they are demonstrating on if you get this kit be ready to relocate the unit all the way to the left hand side of the bike and even so it will still rub and smash aginst the unit also flex pipe rubs on the engine so you will need to zip tie it to make it a bit higher to get it off the block

[@davidbaxter6840]

Just added snorkel and sensor deletes on a 2024 forman 520 took it out and it wont idle under water is there something i can do to help that

[@justin-pi3dk]

turn your idle up so

[@vesselpowersports]

Idle it up and make sure your spark plug boot is greased

[@JCool101]

I’ve done the baffle delete as it was leaking some no snorkel yet. As for the airbox drain do you just the stock cap and clamp ? Or is it safe as is ?

[@JCool101]

Also unrelated question to the video about wheel setups. Would 28x10x12 zillas all the way around fit alright on a stock setup?

[@vesselpowersports]

Stock clamp and plug yes, and yes that setup would be fine