How To Install Chamberlain B503 Garage Door Opener - Detailed instructions

Check out how easy it is to install a Chamberlain B503 garage door opener! In this video I show you step-by-step how to install the garage door opener by yourself using basic tools. This video features the Chamberlain B503 Belt Drive 1/2 horsepower opener, but the steps and instructions apply to a wide variety of other openers from Liftmaster, Decko, Sommer, Genie, Skylink, Ryobi, Direct Drive, GarageMage, Allister, Linear, Sears, Craftsman, Wayne Dalton, etc. Mash that subscribe button to follow along!
Tools required:
Drill
Measuring tape
Pencil
Level
Ladder
Bungie cords or rope
Hack saw
Socket wrench
#Chamberlain503 #GarageDoorOpener #ChamberlainInstall
You can help me with future projects!
www.buymeacoffee.com/amplifydiy
AmplifyDIY is a channel dedicated to do-it-yourself projects with in-depth tutorials on a wide range of subjects.
New videos are published frequently. Want to make sure you don't miss any? Subscribe now!
kzbin.info?su...
Check out the full channel here:
/ amplifydiy
Follow builds in real-time on Instagram!
/ amplifydiy
Feel Good Rock by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/

[@Nicesky2007]

Thank you for your helpful video! I installed this opener yesterday. Went perfectly, thanks to you. I watched your video prior to starting the project, and as I went through the instruction manual that came with the opener, I found myself going back to your video and being able to understand exactly what I needed to do. The instruction manual was not always precise when describing a procedure so I would watch your video and say to myself, "Oh, that's what they mean...." Great job!

[@jiajieyu7654]

Hi Sir, the installation was great! It was very detailed. But there is one thing I want to correct you based on my installation experience. The problem you had in the video was not due to your belt installation, actually you did right at the first time. The only thing you did wrong was you should pull down the emergency handle string, and manually lift up your garage door, and pull it back close to the motor, you will hear a sound like 'click'. Then that is in the right position. Put the emergency handle back to the lock position. Then you can do programming right away. It is much easier than reinstall the belt.

[@millikenway]

The video is super nice but your music is killing. If I like to have music I won't be watching you for it. I find it very distracting and it is like listening to a lecture but with loud noises interfering. Music is very personal, and I found it as noise. Just my two cents if the prime objective is to let viewers watch closely on what you are saying. Thank you for spending the time to make the job easy for us.

[@DanielGoodwin-bh6ex]

Thank you for being the ONLY instructional video on this subject that actually showed how to connect the trolley back up to the chain drive.

[@bbaaspencer1]

If you use a LED bulb, make sure they the ones made for garage door openers. Regular LED bulbs can cause interference and may reduce range or make your remotes inoperative. I install garage doors and openers and I know about the problems it creates by using common LED bulbs! All the garage door opener companies have them available at home improvement stores.

[@herbfreuen9794]

Finally found someone who knew what he was doing. Spent numerous hours searching for adjustment directions on a belt drive.

[@sunyoungg5634]

Never needed to remove the belt - just needed to set the travel limits. Also, the excessive torque seen when it hit the bottom would not occur if the manufacturers instructions were follow - immediately after the full Open and Closed limits are set, the Opener will travel closed and open to record the normal load and with that it will set the Over-Torque just a little above that.

[@jackejr74]

Good Video although the music distracts from the ability to hear you and the music is quite annoying....

[@nicolasfreudemann6304]

Another helpful tip. I install garage doors and openers and if you don't have bungee cords you can open the door manually to hold the opener until you can get up and use the hangings to hang the open safely and then once it's hanged you can close the door.

[@zacksgaragedoorserviceandr1208]

This is the first video that I watched that everything was done correctly some people do some stupid stuff to install the garage door opener and it will not last so you did a very good job on your garage door opener

[@W4lt007]

Finally a video where the wires as my house are the same colors lol

[@johnlorens8275]

Well done. Clear & concise. Very handy tip about using the Bungee Cord.

[@blueriomedina1209]

This was excellent I am going to try to install one of this openers in my garage actually two since I have two separate garage doors. You are a natural at showing/teaching, very smooth easy to follow thanks.

[@cmercado317]

thank you for your time and help me install my garage opener till next time . hope to see more video from this channel

[@philiphernandez3172]

Ridiculously easy with your guidance. Thank you!

[@phillips278]

Good job, awesome instructions and very helpful, Thank you.

[@nodd85]

Nice install!

[@arnoldmilledge2779]

Excellent, great job, simple explanation very easy to understand. Excellent video quality.. Many thanks.

[@joesturnick]

Super helpful video! Thank you!!!

[@petec1173]

Thank you so much, dude. You made my day. This is a helpful and instructive installation video. Couldn't ask for more. Top notch